Nokia Lumia 510 User manual

Check the repair
policy before
performing any
mechanical repair
on Service Level
1&2!
Service Manual for L1 and L2
Nokia Lumia 510
RM-889 RM-898
Key features
zWindows Phone 7.5 / 7.8 OS
zLarge 4" display
z5 Megapixel camera
z800 MHz Snapdragon processor
z256 MB RAM, 4GB internal storage + SkyDrive
Version 1.0
Exploded view Disassembly steps Disassembly video
Assembly hints Assembly video Solder components
Service devices Product controls and interfaces Service concept
Phone reset
©2012 Nokia | Nokia Internal Use only | All Rights Reserved.
More More More
More More More
More More More
More

Service Manual Level 1 and 2
Nokia Lumia 510
RM-889 RM-898
Version 1.0
Exploded view
TP/LCM SPONGE
I0001
DISPLAY
I0003
TOUCH PANEL ADHESIVE
I0005
A-COVER
I0006
EARPIECE
I0007
VOLUME KEY
I0008
POWER KEY
I0010
LIGHT SWAP PWB
I0011
PROXIMITY SENSOR RUBBER
I0016
TP CONNECTOR RUBBER
I0018
TYPE LABEL
I0014
MYLAR RECEIVER
I0022
CAMERA
I0024
GPS ANTENNA
I0028
D-COVER
I0029
TOUCH PANEL
I0002
LIGHT GUIDE
I0004
CAMERA KEY
I0009
RF SHIELD
I0012
BASEBAND SHIELD
I0013
MIC RUBBER
I0015
LCD CONNECTOR RUBBER
I0017
BACK & HOME
KEY LED SPONGE
I0019
SEARCH KEY LED SPONGE
I0020
SPEAKER SEALING SPONGE
I0021
MYLAR USB
I0023
IHF SPEAKER
I0025
MAIN ANTENNA
I0027
SPEAKER MESH
I0026
BATTERY COVER
I0031
SCREW TORX+ SIZE 5
I0030
A-COVER ASSEMBLY
(I0005, I0006)
2
LIGHT SWAP PACKAGE
(I0011-I0023)
3
D-COVER ASSEMBLY
(I0026-I0029)
4
TOUCH PANEL ASSEMBLY
(I0001, I0002)
v1.0 Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2012 Nokia | Nokia Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia Lumia 510
RM-889 RM-898
Version 1.0
Disassembly steps
For disassembling you need the Nokia Standard toolkit version 2. You will also need the camera removal
tool SS-287.
Protect the TOUCH SCREEN with protective film.

Use the finger groove to release the BATTERY COVER.
Remove the BATTERY COVER. If there is a battery inside, remove it also.

Unscrew the eight TORX+ size 5 screws in the order shown. Do not use the screws again. Discard them.
Use the srt-6 to release these two snaps.

Release also these two snaps on the the other side of the device.
Lift up the D-COVER ASSEMBLY bottom end first.

Remove the D-COVER.
Use tweezers to remove the CAMERA KEY.

Remove the POWER KEY.
Remove also the VOLUME KEY.

Disconnect the touch connector with the SS-93. Be careful not to damage the rubber around the
connector or any components nearby.
Disconnect the DISPLAY connector with the SS-93. Be careful not to damage the rubber around the
connector or any components nearby.

Release the clip holding the ENGINE BOARD with the SS-93.
Lift up The ENGINE BOARD as shown.

Carefully release the EARPIECE with the dental tool. Be careful not to injure yourself with the sharp end
of the dental tool.
Remove the EARPIECE. Do not use it agin. Discard it.

Insert the SRT-6 into the earpiece hole. Carefully lift up the TOUCH PANEL for 10 seconds to loosen the
adhesive.
Continue detaching the TOUCH PANEL by sliding the SRT-6 to the right. Then slide the SRT-6 to the left.
Be careful not to damage the flex underneath.

Continue by releasing the TOUCH PANEL side and the bottom end with the SRT-6.
Release also the other side with the SRT-6.

Use tweezers to pull the connector flex through the A-COVER hole.
Separate the A-COVER and the TOUCH PANEL.

Protect the DISPLAY with protective film.
Remove the LIGHT GUIDE with tweezers.

Use the SRT-6 to release the DISPLAY. Be careful not to damage the flex underneath.
Use tweezers to put the connector flex through the A-COVER hole.

Separate the A-COVER and the DISPLAY. Note that the A-COVER can not be used again.
Remove the MIC RUBBER with tweezers.

Remove the SEARCH KEY and the BACK & HOME KEY LED SPONGEs with tweezers. Do not use them again.
Discard them.
Peel off the MYLAR USB with tweezers. It is not reusable. Discard it.

Remove the PROXIMITY SENSOR RUBBER with tweezers.
Release one corner of the MYLAR RECEIVER with the SS-93. Peel it off with tweezers and discard it.

Remove the LCD CONNECTOR RUBBER with tweezers. Do not use it again. Discard it.
Release the SPEAKER SEALING SPONGE with the SS-93. Remove it with tweezers. Do not use it again. Be
careful not to damage the components on the ENGINE BOARD.