Nokia Lumia 610 User manual

Service Manual for L1 and L2
Nokia Lumia 610
RM-835 RM-836
Key features
Most affordable Nokia Lumia yet
Updated Windows Phone operating system
8 GB internal mass memory
3.7" WVGA 800 x 480 pixels LCD TFT display
Version 1.0
Exploded view Disassembly steps Assembly steps
Solder components Service devices Product controls and interfaces
Service concept Phone reset
©2012 Nokia | Nokia Internal Use only | All Rights Reserved.
More More More
More More More
More More

Service Manual Level 1 and 2
Nokia Lumia 610
RM-835 RM-836
Version 1.0
Exploded view
A-COVER
I0002
EARPIECE
I0003
SECONDARY MIC RUBBER
I0008
LIGHT SWAP PWB
I0018
SHIELDING LID 2
I0016
TOUCH PANEL
CONNECTOR RUBBER
I0012
LED FLASH RUBBER
I0017
POWER KEY
I0006
VOLUME KEY
I0004
CAMERA
I0020
LED FLASH
I0025
LED FLASH ADHESIVE
I0026
AV JACK
I0023
AV JACK ADHESIVE
I0024
D-COVER
I0029
BT/GPS/WLAN ANTENNA
I0028
KEY LED RUBBER
I0009
TOUCH PANEL
I0001
DISPLAY
I0007
DISPLAY CONDUCTIVE TAPE
I0010
ANTENNA RUBBER
I0014
LCD CONNECTOR RUBBER
I0011
BATTERY COVER
I0031
SHIELDING LID 1
I0015
SIM TAPE
I0013
CAMERA KEY
I0005
IHF SPEAKER GASKET
I0022
IHF SPEAKER
I0021
TYPE LABEL
I0019
MAIN ANTENNA
I0027
SCREW TORX+ SIZE 4
I0030
A-COVER ASSEMBLY
(I0001 - I0003)
1
LIGHT SWAP PACKAGE
(I0008 - I0019) 2
D-COVER ASSEMBLY
(I0021 - I0029) 3
Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2012 Nokia | Nokia Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia Lumia 610
RM-835, RM-836
Version 1.0
Disassembly steps
For disassembling you need the Nokia Standard toolkit version 2. You will also need the camera removal
tool SS-287 and an AV plug.
Protect the A-COVER with protective film.

Open the BATTERY COVER by pulling it to the direction shown. Remove the BATTERY COVER.
Unscrew the eight Torx+ size 4 screws in the order shown. Do not use them again. Discard them.

Insert the SRT-6 to the shown place and release the bottom end of the D-COVER.
Release also both sides of the D-COVER with the SRT-6.

Lift up the bottom end of the D-COVER and pull it to the direction shown. The D-COVER can now be
separated.
Remove the CAMERA KEY with tweezers.

Remove the POWER KEY with tweezers.
Remove the VOLUME KEY with tweezers.

Use the SS-93 to open the TOUCH PANEL connector. Be very careful not to damage the connector or
the small components around the connector.
Open the DISPLAY connector with the SS-93. Be careful not to damage the connector or components
nearby.

Open the two shown clips holding the ENGINE BOARD with the sharp end of the SS-93.
Lift up the bottom end of the ENGINE BOARD and pull it to the direction shown. The ENGINE BOARD can
now be separated.

Lift up the DISPLAY with the SS-93 and remove it.
Protect the other side of the A-COVER with protective film.

Protect the DISPLAY with protective film.
Release the EARPIECE with the dental tool. Be careful not to injure yourself with the sharp end of the
dental tool! Remove the EARPIECE with tweezers. Do not use it again. Discard it.

Remove the EARPIECE adhesive remains from the A-COVER. Discard them.
Release the IHF SPEAKER with the SS-93 as shown.

Remove the IHF SPEAKER and discard it.
Remove the IHF SPEAKER GASKET. The IHF SPEAKER GASKET is not reusable. Disacrd it.

Lift up and remove the AV JACK with an AV plug.
Remove the AV JACK ADHESIVE from the D-COVER. Do not use it again.

Push the LED FLASH gently with the sharp end of the SS-93. Remove the LED FLASH with tweezers.
Remove the LED FLASH ADHESIVE. Discard it.

Release the LED FLASH RUBBER with the dental tool. Be careful not to damage the nearby components.
Remove the LED FLASH RUBBER with tweezers.
Remove the CAMERA with the camera removal tool SS-287. Please note that the tool used in this picture
is not SS-287.

Release the SHIELDING LID 2 with the SS-93. Remove it with tweezers and discard it.
Release also the SHIELDING LID 1 with the SS-93. Remove it with tweezers. Do not use it again. Discard
it.

Release the LCD CONNECTOR RUBBER with the dental tool. Be careful not to damage the nearby
components. Remove it with tweezers. Do not use it again. Discard it.
Release the TOUCH PANEL CONNECTOR RUBBER with the dental tool. Be careful not to damage the
nearby components. Remove it with tweezers. Do not use it again. Discard it.

Lift up the SIM TAPE with the dental tool. Be careful not to damage the nearby components. Remove it
with tweezers. Do not use it again. Discard it.
Release the ANTENNA RUBBER with the dental tool. Be careful not to damage the nearby components.
Remove it with tweezers. Discard it.

Release the SECONDARY MIC RUBBER with the dental tool. Be careful not to damage the SECONDARY MIC
or any nearby components. Remove it with tweezers. Do not use it again.
Release the KEY LED RUBBER with the dental tool. Be careful not to damage the nearby components.
Remove it with tweezers. Do not use it again. Discard it.