Nokia TA-1298 Specification sheet

1. Insert the SIM and memory
card
1. Put your fingernail in the seam between the back
cover and the display, bend the back cover open,
and remove it.
2. Slide the nano-SIM in slot 1 with the contact area
face down. If you have a second SIM, slide it in slot
2.
3.If you have a memory card, slide it in the memory
card slot.
4.Put back the back cover.
Use only original nano-SIM cards. Use of
incompatible SIM cards may damage the card or the
device, and may corrupt data stored on the card.
Use only compatible memory cards approved for
use with this device. Incompatible cards may
damage the card and the device and corrupt data
stored on the card.
Important: Do not remove the memory card
when an app is using it. Doing so may damage the
memory card and the device and corrupt data
stored on the card.
Note: Switch the device off and disconnect the
charger and any other device before removing any
covers. Avoid touching electronic components while
changing any covers. Always store and use the
device with any covers attached.
Both SIM cards are available at the same time when
the device is not being used, but while one SIM card
is active, for example, making a call, the other may
be unavailable.
Note: On dual SIM capable devices, both SIM1
and SIM2 slots support 4G networks. However, if
your SIM1 and SIM2 are both LTE SIM cards, the
primary SIM supports 4G/3G/2G networks, while
the secondary SIM can only support 3G/2G. For
more information on your SIM cards, contact your
service provider.
2. Charge the battery and switch
the phone on
Plug a compatible charger into a wall outlet, and
connect the cable to your phone. Your phone
supports the USB micro-B cable. You can also
charge your phone from a computer with a USB
cable, but it may take a longer time.
If the battery is completely discharged, it may take
several minutes before the charging indicator is
displayed.
To switch your phone on, press and hold the power
key until the phone vibrates. The phone guides you
through the setup.
For an online user guide and troubleshooting help,
go to www.nokia.com/mobile-support.
Get Started
Nokia xx
Mobile Phone
TA-1298
EN-LATAM
Camera
Headset connector
Microphone
USB connector
Google Assistant/
Google Search key*
Earpiece
Volume keys
Power/Lock key
*Google Assistant is not available in certain languages and
countries. Where not available, Google Assistant is replaced
by Google Search. Check availability at https://
support.google.com/assistant.
Fingerprint
sensor
Flash
Front camera
Proximity
sensor

Product and safety info
Important: For important info onthe safe use of your device and
battery, read the Product and safety info booklet before you take
your device into use.
You can only use your device on the GSM 850, 900, 1800, 1900;
WCDMA 1, 2, 4, 5, 8; LTE 1, 2, 4, 5, 7, 8, 12, 17, 28, 66 networks.
You need a subscription witha service provider.
Important: 4G/LTE might not be supported by your network
service provider or bythe service provider you are using when
traveling. In these cases, youmay not be able tomake orreceive
calls, send or receive messages or use mobile dataconnections. To
make sure your device works seamlessly when full 4G/LTE service is
not available, it is recommended that you change the highest
connection speed from4G to3G. To do this, on the home screen,
tap Settings > Network & Internet > Mobile network > Advanced,
and switch Preferred network type to 3G.
For more info, contact your network service provider.
Charge your device withthe ES006C-U050100OOE (EU plug) /
DCS10-0501000F (US plug) charger. HMD Global may make
additional battery or charger models available forthis device.
Charging time can vary depending on device capability. Some ofthe
accessories mentioned in this user guide, such as charger,headset,
or data cable, may be sold separately.
Electrical Information ofthe Charger
The following electrical information corresponds tothe above-
mentioned charger models:
Input: 100-240 Vac 50/60Hz 0,3A
Output: 5,0 V 1,0 A 5,0 W
Charger safety instructions
The charger is suitable tobe usedonly with compatible devices.
The charger should not be used in extremely high or low
temperatures.
Ventilation should not be obstructed by covering the charger with
magazines, blankets, curtains etc.
Open flames, such as candles, should not be placed above the
charger.
The charger and the wall outlet shall be easily accessible at all times.
In case the cable or the plugs are damaged, stop using it.
The charger requires very lowmaintenance. Ifyou want toclean it,
use a dry cloth or a brush.
Meaning of the symbols:
For internal use only
The charger should not be disposed as unsorted municipal
waste. It should be recycled.
The surface of the device is nickel-free.
Parts of the device are magnetic. Metallic materials may be
attracted to the device. Do not place credit cards or other magnetic
stripe cards near the device for extended periods of time, since the
cards may be damaged.
Note: Pre-installed system software and apps use a significant
part of memory space.Keep a safe distance when using the flash. Do
not use the flash on people or animals at close range. Do not cover
the flash while taking a photo.
Certification information (SAR)
This mobile device meets guidelines for exposure to radio waves as
set forth by the Federal Communications Commission (FCC). Refer
to the following.
FCC RF Exposure Information
Your handset is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to
radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. The guidelines are based on
standards that were developed by independent scientific
organization through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety margin designed
to assure the safety of all persons, regardless of age and health. The
exposure standard for wireless handsets employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC is 1.6 W/kg. The tests are performed in
positions and locations (e.g. at the ear and worn on the body) as
required by the FCC for each model. The highest SAR value for this
handset model as reported to the FCC when tested for use at the ear
is X.XX W/kg, and when worn on the body in a holder or carry case, is
X.XX W/kg.
Body-worn Operation; This device was tested for typical body-worn
operations with the handset kept xx cm from the body. To maintain
compliance with FCC RF exposure requirements, use accessories
that maintain a xx cm separation distance between the user’s body
and the handset. The use of belt clips, holsters and similar
accessories should not contain metallic components in its assembly.
The use of accessories that do not satisfy these requirements may
not comply with FCC RF exposure requirements, and should be
avoided. The FCC has granted an Equipment Authorization for this
handset model with all reported SAR levels evaluated as in
compliance with the FCC RF emission guidelines. SAR information on
this handset model is on file with the FCC and can be found under
the FCC ID Search section of www.fcc.gov/oet/ea/ after searching
on FCC ID 2AJOTTA-1298.
Additional information on Specific Absorption Rates (SAR) can be
found on the FCC website at www.fcc.gov/general/radio-
frequency-safety-0.
To send data or messages, a good connection to the network is
needed. Sending may be delayed until such a connection is available.
Follow the separation distance instructions until the sending is
finished.
During general use, the SAR values are usually well below the values
stated above. This is because, for purposes of system efficiency and
to minimise interference on the network, the operating power of
your mobile is automatically decreased when full power is not
needed for the call. The lower the power output, the lower the SAR
value.
Device models may have different versions and more than one
value. Component and design changes may occur over time and
some changes could affect SAR values.
For more info, go to www.sar-tick.com. Note that mobile devices
may be transmitting even if you are not making a voice call.
Your mobile device is also designed to meet the United States
Federal Communications Commission (FCC) guidelines. FCC ratings
for your device and more information on SAR can be found at http:/
/transition.fcc.gov/oet/rfsafety/sar.html.
The World Health Organization (WHO) has stated that current
scientific information does not indicate the need for any special
precautions when using mobile devices. If you are interested in
reducing your exposure, they recommend you limit your usage or
use a hands-free kit to keep the device away from your head and
body. For more information and explanations and discussions on RF
exposure, go to the WHO website at www.who.int/peh-emf/en.
Copyrights and other notices
FCC notice:
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. For more info, go to www.fcc.gov/
engineering-technology/electromagnetic-compatibility-division/
radio-frequency-safety/faq/rf-safety. Any changes or
modifications not expressly approved by HMD Global could void the
user’s authority to operate this equipment. Note: This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device has an electronic label for certification information. To
access it, select Settings > System > Certification.
© 2020 HMD Global. HMD Global Oy is the exclusive licensee of the
Nokia brand for phones & tablets. Nokia is a registered trademark of
Nokia Corporation.
Android, Google and other related marks and logos are trademarks
of Google LLC.
SAR Information Statement
Your Mobile Phone is a radio transmitter and receiver. It is designed
and manufactured not to exceed the emission limits for exposure to
radiofrequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy for
the general population. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include a
substantial safety margin designed to assure the safety of all persons,
regardless of age and health. The exposure standard for wireless mobile
phones employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are
conducted with the phone transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the phone while operating can
be well below the maximum value. This is because the phone is designed to
operate at multiple power levels so as to use only the power required to
reach the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. Before a phone model is available for
sale to the public, it must be tested and certified to the FCC that it does not
exceed the limit established by the government adopted requirement for
safe exposure. The tests are performed in positions and locations (e.g., at
the ear and worn on the body) as required by the FCC for each model. The
highest SAR value for this model phone when tested for use at the head is
0.249W/Kg and when worn on the body, as described in this user guide, is
0.709W/Kg (Body-worn measurements differ among phone models,
depending upon available accessories and FCC requirements). The
maximum scaled SAR in hotspot mode is 0.736W/Kg. While there may be
differences between the SAR levels of various phones and at various
positions, they all meet the government requirement for safe exposure. The
FCC has granted an Equipment Authorization for this model phone with
all reported SAR levels evaluated as in compliance with the FCC RF
exposure guidelines. SAR information on this model phone is on file with
the FCC and can be found under the Display Grant section of http://
www.fcc.gov/ oet/fccid after searching on
FCC ID: 2AJOTTA-1298 Additional information on Specific
Absorption Rates (SAR) can be found on the Cellular Telecommunications
Industry Association (CTIA) web-site at http://www.wow-com.com. * In
the United States and Canada, the SAR limit for mobile phones used by the
public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The
standard incorporates a substantial margin of safety to give additional
protection for the public and to account for any variations in
measurements.
The SAR test distance is 10mm.