Nokia 7368 ISAM ONT BGW320-505 User manual

Nokia — Proprietary and confidential
Use pursuant to applicable agreements
7368 Intelligent Services Access
Manager ONT
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA
Issue: 01
7368 ISAM ONT BGW320-505 Product Guide
Release 06.02.00b | October 2019 | Edition 01

2
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
Nokia is a registered trademark of Nokia Corporation. Other products and company
names mentioned herein may be trademarks or tradenames of their respective
owners.
The information presented is subject to change without notice. No responsibility is
assumed for inaccuracies contained herein.
© 2019 Nokia.
Contains proprietary/trade secret information which is the property of Nokia and must
not be made available to, or copied or used by anyone outside Nokia without its
written authorization. Not to be used or disclosed except in accordance with
applicable agreements.
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide Preface
Issue: 01 3FE-47753-AAAA-TCZZA 3
1Preface
This preface provides general information about the documentation set for optical
network terminals (ONTs).
1.1 Scope
This documentation set provides information about safety, features and functionality,
ordering, hardware installation and maintenance, and software installation
procedures for the current release.
1.2 Audience
This documentation set is intended for planners, administrators, operators, and
maintenance personnel involved in installing, upgrading, or maintaining the ONTs.
1.3 Required knowledge
The reader must be familiar with general telecommunications principles.
1.4 Acronyms and initialisms
The expansions and optional descriptions of most acronyms and initialisms appear
in the glossary.
1.5 Assistance and ordering phone numbers
Nokia provides global technical support through regional call centers. Phone
numbers for the regional call centers are available at the following URL:
https://customer.nokia.com/support/s/
For ordering information, contact your Nokia sales representative.
Release 06.02.00b | October 2019 | Edition 01

Preface
4
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
1.6 Nokia quality processes
Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These
requirements are documented in the Fixed Networks Quality Manual
3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical
requirements and customer end-point requirements are met. The customer or its
representatives may be allowed to perform on-site quality surveillance audits, as
agreed upon during contract negotiations
1.7 Safety information
For safety information, see the appropriate safety guidelines chapter.
1.8 Documents
Documents are available using ALED or OLCS.
Procedure 1 To download a ZIP file package of the customer documentation
1Navigate to https://customer.nokia.com/support/s/ and enter your user name and password.
If you are a new user and require access to this service, please contact your Nokia sales
representative.
2From the Technical Content for drop-down menu, choose the product.
3Click on Downloads: Electronic Delivery.
4Choose Documentation from the drop-down menu and click Next.
5Select the image from the drop-down menu and click Next.
6Follow the on-screen directions to download the file.
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide Preface
Issue: 01 3FE-47753-AAAA-TCZZA 5
Procedure 2 To access individual documents
Individual PDFs of customer documents are also accessible through the Nokia Customer Support
website.
1Navigate to https://customer.nokia.com/support/s/ and enter your user name and password.
If you are a new user and require access to this service, please contact your Nokia sales
representative.
2From the Technical Content for drop-down menu, choose the product.
3Click on Manuals and Guides to display a list of customer documents by title and part
number. You can filter this list using the Release drop-down menu.
4Click on the PDF to open or save the file.
1.9 Special information
The following are examples of how special information is presented in this document.
Danger — Danger indicates that the described activity or
situation may result in serious personal injury or death; for
example, high voltage or electric shock hazards.
Warning — Warning indicates that the described activity or
situation may, or will, cause equipment damage or serious
performance problems.
Caution — Caution indicates that the described activity or
situation may, or will, cause service interruption.
Note — A note provides information that is, or may be, of
special interest.
Release 06.02.00b | October 2019 | Edition 01

Preface
6
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
1.9.1 Procedures with options or substeps
When there are options in a procedure, they are identified by letters. When there are
required substeps in a procedure, they are identified by roman numerals.
Procedure 3 Example of options in a procedure
At step 1, you can choose option a or b. At step 2, you must do what the step indicates.
1This step offers two options. You must choose one of the following:
aThis is one option.
bThis is another option.
2You must perform this step.
Procedure 4 Example of required substeps in a procedure
At step 1, you must perform a series of substeps within a step. At step 2, you must do what the
step indicates.
1This step has a series of substeps that you must perform to complete the step. You must
perform the following substeps:
iThis is the first substep.
ii This is the second substep.
iii This is the third substep.
2 You must perform this step.
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide Preface
Issue: 01 3FE-47753-AAAA-TCZZA 7
1.10 Multiple PDF document search
You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a
common term. Adobe Reader displays the results in a single display panel. The
results are grouped by PDF file, and you can expand the entry for each file.
Procedure 5 To search multiple PDF files for a common term
1Open Adobe Acrobat Reader.
2Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel appears.
3Enter the search criteria.
4Click on the All PDF Documents In radio button.
5Select the folder in which to search using the drop-down menu.
6Click on the Search button.
Acrobat Reader displays the search results. You can expand the entries for each document
by clicking on the + symbol.
Note — The PDF files in which you search must be in the same
folder.
Release 06.02.00b | October 2019 | Edition 01

Preface
8
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide
Issue: 01 3FE-47753-AAAA-TCZZA 9
Table of contents
1 Preface.............................................................................................3
1.1 Scope ..........................................................................................................3
1.2 Audience......................................................................................................3
1.3 Required knowledge....................................................................................3
1.4 Acronyms and initialisms .............................................................................3
1.5 Assistance and ordering phone numbers ....................................................3
1.6 Nokia quality processes...............................................................................4
1.7 Safety information........................................................................................4
1.8 Documents ..................................................................................................4
1.9 Special information ......................................................................................5
1.9.1 Procedures with options or substeps...........................................................6
1.10 Multiple PDF document search ...................................................................7
2 ANSI ONT safety guidelines ........................................................15
2.1 Safety instructions .....................................................................................15
2.1.1 Safety instruction boxes in customer documentation ................................15
2.1.2 Safety-related labels..................................................................................16
2.2 Safety standards compliance ....................................................................16
2.2.1 EMC, EMI, and ESD standards compliance..............................................17
2.2.2 Equipment safety standard compliance.....................................................17
2.2.3 Environmental standards compliance........................................................18
2.2.4 Resistibility requirements compliance .......................................................18
2.3 Electrical safety guidelines ........................................................................18
2.3.1 Power supplies ..........................................................................................18
2.3.2 Cabling ......................................................................................................18
2.3.3 Protective earth .........................................................................................19
2.4 ESD safety guidelines ...............................................................................19
2.5 Laser safety guidelines..............................................................................19
2.5.1 Normal laser operation ..............................................................................20
2.5.2 Location class............................................................................................20
2.6 Environmental requirements......................................................................20
3 BGW320-505 unit data sheet .......................................................21
3.1 BGW320-505 part numbers and identification...........................................21
3.2 BGW320-505 general description .............................................................22
3.2.1 TR69 authentication using TLS and CA certificates ..................................26
3.3 BGW320-505 software and installation feature support............................26
3.4 BGW320-505 interfaces and interface capacity ........................................27
3.4.1 BGW320-505 connections and components .............................................27
3.5 BGW320-505 service LEDs.......................................................................28
3.6 BGW320-505 detailed specifications.........................................................29
3.7 BGW320-505 GEM ports and T-CONTs ...................................................30
3.8 BGW320-505 standards compliance.........................................................30
3.8.1 Responsible party......................................................................................30
3.8.2 Energy-related products standby and off modes compliance....................31
3.8.3 FCC statement ..........................................................................................31
Release 06.02.00b | October 2019 | Edition 01

10
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
3.8.4 FCC Radiation Exposure Statement .........................................................32
3.9 BGW320-505 special considerations ........................................................32
3.9.1 Wi-Fi service..............................................................................................32
3.9.1.1 Wi-Fi physical features ..............................................................................32
3.9.1.2 Wi-Fi standards and certifications .............................................................33
3.9.1.3 Wi-Fi GUI features.....................................................................................33
3.9.2 BGW320-505 ONT considerations and limitations ....................................33
4 Install an BGW320-505 indoor ONT ............................................35
4.1 Purpose .....................................................................................................35
4.2 General......................................................................................................35
4.3 Prerequisites..............................................................................................35
4.4 Safety information......................................................................................36
4.5 Procedure ..................................................................................................37
5 Replace an BGW320-505 indoor ONT .........................................41
5.1 Purpose .....................................................................................................41
5.2 General......................................................................................................41
5.3 Prerequisites..............................................................................................41
5.4 Safety information......................................................................................42
5.5 Procedure ..................................................................................................43
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide
Issue: 01 3FE-47753-AAAA-TCZZA 11
List of figures
3 BGW320-505 unit data sheet .......................................................21
Figure 1 BGW320-505 ONT unit .............................................................................23
Figure 2 BGW320-505 ONT bottom view ................................................................24
Figure 3 BGW320-505 ONT front and side view .....................................................24
Figure 4 BGW320-505 ONT connections ................................................................25
4 Install an BGW320-505 indoor ONT ............................................35
Figure 5 BGW320-505 ONT connections ................................................................38
5 Replace an BGW320-505 indoor ONT .........................................41
Figure 6 BGW320-505 ONT connections ................................................................44
Release 06.02.00b | October 2019 | Edition 01

12
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide
Issue: 01 3FE-47753-AAAA-TCZZA 13
List of tables
2 ANSI ONT safety guidelines ........................................................15
Table 1 Safety labels ..............................................................................................16
3 BGW320-505 unit data sheet .......................................................21
Table 2 Identification of BGW320-505 indoor ONT ................................................21
Table 3 BGW320-505 indoor ONT interface connection capacity..........................27
Table 4 BGW320-505 indoor ONT physical connections .......................................27
Table 5 BGW320-505 service LED indications ......................................................28
Table 6 BGW320-505 indoor ONT physical specifications.....................................29
Table 7 BGW320-505 indoor ONT power consumption specifications ..................29
Table 8 BGW320-505 indoor ONT environmental specifications ...........................30
Table 9 BGW320-505 indoor ONT capacity for GEM ports and T-CONTs ............30
Table 10 Responsible party contact information ......................................................31
Table 11 BGW320-505 ONT considerations and limitations ....................................33
Release 06.02.00b | October 2019 | Edition 01

14
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide ANSI ONT safety guidelines
Issue: 01 3FE-47753-AAAA-TCZZA 15
2 ANSI ONT safety guidelines
This chapter provides information about the mandatory regulations that govern the
installation and operation of the optical network terminals or units (ONTs or ONUs)
in the North American or ANSI market.
2.1 Safety instructions
This section describes the safety instructions that are provided in the ONT customer
documentation and on the equipment.
2.1.1 Safety instruction boxes in customer
documentation
The safety instruction boxes are provided in the ONT customer documentation.
Observe the instructions to meet safety requirements.
The following is an example of the Danger box.
The Danger box indicates that the described activity or situation may pose a threat
to personal safety. It calls attention to a situation or procedure which, if not correctly
performed or adhered to, may result in death or serious physical harm.
Do not proceed beyond a Danger box until the indicated conditions are fully
understood and met.
The following is an example of the Warning box.
The Warning box indicates that the described activity or situation may, or will, cause
equipment damage, loss of data, or serious performance problems. It identifies a
possible equipment-damaging situation or provides essential information to avoid the
degradation of system operations or data.
Do not proceed beyond a warning until the indicated conditions are fully understood
and met.
Danger — Possibility of personal injury.
Warning 1 — Possibility of equipment damage.
Warning 2 — Possibility of data loss.
Release 06.02.00b | October 2019 | Edition 01

ANSI ONT safety guidelines
16
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
The following is an example of the Caution box.
The Caution box indicates that the described activity or situation may, or will, cause
service interruption.
Do not proceed beyond a caution until the indicated conditions are fully understood
and met.
The following is an example of the Note box.
The Note box provides information that assists the personnel working with ONTs. It
does not provide safety-related instructions.
2.1.2 Safety-related labels
The ONT equipment is labeled with specific safety compliance information and
instructions that are related to a variant of the ONT. Observe the instructions on the
safety labels.
Table 1 provides examples of the text in the various ONT safety labels.
Table 1 Safety labels
2.2 Safety standards compliance
This section describes the ONT compliance with North American safety standards.
Caution 1 — Possibility of service interruption.
Caution 2 — Service interruption.
Note — Information of special interest.
Description Label text
CE marking There are various CE symbols for CE compliance.
Warning — Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide ANSI ONT safety guidelines
Issue: 01 3FE-47753-AAAA-TCZZA 17
2.2.1 EMC, EMI, and ESD standards compliance
The ONT equipment complies with the following requirements:
•Federal Communications Commission (FCC) CFR 47, Part 15, Subpart B,
Subpart C, and Subpart E, Class A requirements for OLT equipment
•SPS-1019_Reliability_Env_Mech v2_5_REL_07-17-17, including sections:
•3.3 ESD Test
•3.4 Surge Test
•6.8 EMC Shielding
•8.13 FCC Certification - Intentional Radiators
•8.14 FCC Certification - Unintentional Radiators
•EN 61000-4-4 Testing and measurement techniques - Electrical fast
transient/burst immunity test
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
•Consult the dealer or an experienced radio/TV technician for help.
2.2.2 Equipment safety standard compliance
The ONT equipment complies with the requirements of UL60950-1 and Indoor ONTs
to Information Technology Equipment (ITE).
Release 06.02.00b | October 2019 | Edition 01

ANSI ONT safety guidelines
18
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
2.2.3 Environmental standards compliance
The ONT equipment complies with the following standards:
•SPS-1019_Reliability_Env_Mech v2_5_REL_07-17-17 Section 6 Environmental
Requirements
2.2.4 Resistibility requirements compliance
The ONT equipment complies with the requirements of ITU Recommendation K.21
for resistibility of telecommunication equipment installed in customer premises to
overvoltage and overcurrents.
2.3 Electrical safety guidelines
This section provides the electrical safety guidelines for the ONT equipment.
2.3.1 Power supplies
The use of any non-Nokia approved power supplies or power adapters is not
supported or endorsed by Nokia. Such use will void any warranty or support contract
with Nokia. Such use greatly increases the danger of damage to equipment or
property.
2.3.2 Cabling
The following are the guidelines regarding cables used for the ONT equipment:
•Use only cables approved by the relevant national electrical code.
•The ONTs have been evaluated for use with external POTS wiring without primary
protection that may not exceed 140 ft (43 m) in reach. However, the power cable
must not exceed 100 ft (31 m).
Note — The ONTs comply with the U.S. National Electrical
Code. However, local electrical authorities have jurisdiction
when there are differences between the local and U.S.
standards.
Release 06.02.00b | October 2019 | Edition 01

7368 ISAM ONT BGW320-505 Product Guide ANSI ONT safety guidelines
Issue: 01 3FE-47753-AAAA-TCZZA 19
2.3.3 Protective earth
Earthing and bonding of the ONTs must comply with the requirements of NEC article
250 or local electrical codes.
2.4 ESD safety guidelines
The ONT equipment is sensitive to ESD. Operations personnel must observe the
following ESD instructions when they handle the ONT equipment.
During installation and maintenance, service personnel must wear wrist straps to
prevent damage caused by ESD.
Nokia recommends that you prepare the site before you install the ONT equipment.
In addition, you must control relative humidity, use static dissipating material for
furniture or flooring, and restrict the use of air conditioning.
2.5 Laser safety guidelines
Observe the following instructions when you perform installation, operations, and
maintenance tasks on the ONT equipment.
Only qualified service personnel who are extremely familiar with laser radiation
hazards should install or remove the fiber optic cables and units in this system.
Observe the following danger for laser hazard. Eyes can be damaged when they are
exposed to a laser beam. Take necessary precautions before you plug in the optical
modules.
Caution — This equipment is ESD sensitive. Proper ESD
protections should be used when entering the TELCO Access
portion of the ONT.
Danger — There may be invisible laser radiation at the fiber
optic cable when the cable is removed from the connector.
Avoid direct exposure to the laser beam.
Danger — Possibility of equipment damage. Risk of eye
damage by laser radiation.
Release 06.02.00b | October 2019 | Edition 01

ANSI ONT safety guidelines
20
7368 ISAM ONT BGW320-505 Product Guide
3FE-47753-AAAA-TCZZA Issue: 01
2.5.1 Normal laser operation
In normal operation, fiber cable laser radiation is always off until it receives signal
from the line terminal card.
Eyes can be damaged when they exposed to a laser beam. Operating personnel
must observe the instructions on the laser explanatory label before plugging in the
optical module.
2.5.2 Location class
Use cable supports and guides to protect the receptacles from strain.
2.6 Environmental requirements
See the ONT technical specification documentation for temperature ranges for
ONTs.
Danger — Risk of eye damage by laser radiation.
Release 06.02.00b | October 2019 | Edition 01