Nokia MEDIAMASTER 9450 S User manual

Owner's Manual
MEDIAMASTER
9450 S

GB 2

GB 3
Contents
FOR YOUR SAFETY 4
Rear panel 4
Front panel 5
INSTALLATION OF THE MEDIAMASTER 5
Connecting the Mediamaster to the satellite
dish 6
Connecting the Mediamaster to a TV set 6
Connecting to a TV and a video recorder 7
If our VCR does not have a SCART-
Connector 7
Connecting to an analogue satellite-
receiver and a video recorder 7
Connecting to Hi Fi s stem 8
Preparing the remote control 8
Before ou continue 8
REMOTE CONTROL 9
ASIC SETTINGS 10
Tuning procedure when RF
Connections are used 10
The Welcome Menu 11
Language settings 11
Antenna Satellite configuration 11
Automatic channel Search 12
Manual channel Search 13
VIEWING TV 13
General information 13
TV screen format 14
Start/stop watching TV 14
Select channel 14
Program Information, the i button 14
TV Guide 15
The Radio button 15
Volume level 15
List of TV channels 15
List of Radio channels 16
Video recorder 16
Subtitling and Teletext. The TEXT Button 16
SETTING FROM THE MAIN MENU 16
TV channels and radio channels 17
TV Guide and Radio Guide 17
Edit Channels 17
Rearrange List 18
Rename List 18
Add channels 18
Lock channels 18
Rearrange channels 19
Remove channels 19
USER PREFERENCES 19
Parental control 19
Language settings 20
S stem settings 20
On/Off Timer setting 21
GAME 21
INSTALLATION SU MENUS 22
Antenna Satellite configuration 22
Automatic channel search 22
Manual channel search 22
Advanced channel search 22
Reinstall 23
S stem Information 23
GLOSSARY OF TERMS 24
PRO LEM SOLVING 25
TECHNICAL SPECIFICATION 26
MENUS SCREEN STRUCTURE 27
Nokia Multimedia Terminals operates a polic of continuous development.
Therefore we reserve the right to make changes and improvements to an
of the products described in this manual without an prior notice.
The EMC Directive 89/336/EEC is applied to this product.
DiSEqC is a trademark of EUTELSAT
Nokia is a registered trademark of Nokia Corporation.
Cop right 2000. Nokia Multimedia Terminals.
All rights reserved.
MEDIAMASTER 9450 S

GB 4
Keep a clear space around the Mediamaster to allow for sufficient ventilation.
Do not cover the Mediamaster or place it on a unit that emits heat.
 Use a soft cloth and a mild solution of dish washing liquid to clean the casing.
 Never allow liquids, spra or other materials to come into contact with the inside of the
Mediamaster.
 Service should be carried out onl at a Nokia authorized service center.
 Do not connect or modif cables when the Mediamaster is plugged in.
 Do not remove the cover.
 Do not allow the unit to be exposed to hot, cold or humid conditions.
 Please note that the onl wa to isolate the Mediamaster completel from the 230 V mains suppl
is to unplug the mains lead!
FOR YOUR SAFETY
Rear panel
RS232
For a PC.
LN input
Satellite dish
input
(F-connector).
LN output
Satellite signal (IF) output
with loop through. For
connection to the other
satellite receiver if needed.
TV SCART
For the audio
/video input of the
TV set.
TV AERIAL
For a terrestrial
(conventional)
TV aerial.
AUX SCART
For connection to a
VCR or an analogue
satellite receiver.
V
IDEO OUTPUT
Composite video
signal output for a
TV set.
AUDIO L R
Stereo outputs for
connection to a HiFi
s stem.
POWER CA LE
230 V AC
50 Hz
TV/VCR
For an RF-Cable
to the aerial
input of the TV
or VCR.

GB 5
The box for our Mediamaster should contain the following items:
Mediamaster 9450S includes
About the SCART sockets
The rear panel of the Mediamaster is equipped with 2 SCART sockets.
When you connect other products to any of these sockets, always
use fully featured SCART cables (as supplied). There are less well
specified SCART cables on the market and picture qualit could be
reduced if ou use them.
SCART cables are also necessar to get stereo sound from a stereo TV and video recorder.
Front panel
Power
To turn the receiver
on/off (standb ).
Up/Down
Select channel number,
up/down.
Display
Shows channel number, remote control signal and time in standb mode.
At start up, it displa s the model number.
INSTALLATION OF THE MEDIAMASTER
SCART-Cable Owner s
Manual
Remote Controller
and Batteries

GB 6
Installing the satellite dish
 Your satellite dish should be installed with a cable for ou
to connect to the Mediamaster. If ou do not have this cable
ou will need to bu one from a dealer (tell the dealer ou
need a coaxial cable and F-connectors).
 Connect the cable from the satellite dish to the socket
marked LNB IN on the back of the Mediamaster.
If you need to fit the F-connectors onto the cable
Prepare each end of the cable as shown in the diagram.
You will need to fold back the outer braid (as shown).
 Slide the F-connector onto the cable, and then turn it
clockwise until it grips the braid.
 Ensure that 3 mm of the core is protruding from the end of
the connector.
There are man different t pes of TV/VCR and other
equipment that ou can connect to the Mediamaster. In this
manual ou will see some of the most common wa s to
connect our equipment. If ou use RF cables ou will
have to tune our TV and VCR to the Mediamaster output
channel. If ou have problems with our connections and
need help, contact your dealer or Service Provide.
 Connect the SCART cable between the main SCART
socket on the TV and the TV SCART socket on the
Mediamaster.
 Connect an RF cable from the TV/VCR output on the
Mediamaster to the RF input socket on the TV.
 Connect the TV aerial to the TV AERIAL input socket on the Mediamaster.
15mm
8mm
F-connector
3mm
Connecting the Mediamaster to the satellite dish
Connecting the Mediamaster to a TV set

GB 7
Refer to our video recorder manual for full instructions.
 Connect one SCART cable between the main SCART
socket on the TV and the TV SCART socket on the
Mediamaster.
 Connect another SCART cable between the VCR and
the AUX SCART socket on the Mediamaster.
 Connect the RF cable from the RF output on the VCR
to the TV aerial input on the TV.
 Connect the TV aerial to the RF input socket on the VCR.
 Connect a SCART cable between the main SCART
socket on the TV and the TV SCART socket on the
Mediamaster.
 Connect an RF cable from the RF output on the VCR to
the TV aerial input on the TV.
 Connect an RF cable from the TV/VCR output on the
Mediamaster to the RF input socket on the VCR.
 Connect the TV aerial to the TV AERIAL input socket on the Mediamaster.
 Connect a SCART cable between the main
SCART socket on the TV and the TV SCART
socket on the Mediamaster.
 Connect a SCART cable between the VCR and the
AUX SCART socket on the Mediamaster.
 Connect an RF cable from the RF output on the
VCR to the TV aerial input on the TV.
 Connect an RF cable from the RF output on the
Analogue receiver to the RF input socket on the
VCR.
 Connect the TV aerial to the RF input socket on the
Analogue receiver.
In order to switch the signal from the dish between the analogue and digital receivers, ou need a
Universal Twin LNB.
 Cable A between output A on the LNB to the LNB socket on the analogue receiver.
 Cable B between output on the LNB to the ANTENNA socket on the Mediamaster.
Both the VCR and the analogue satellite receiver must be tuned to different UHF channels (than the
Mediamaster) when using RF-connectors.
Connecting to a TV and a Video recorder
If Your VCR does not have a SCART connector
Connecting to an Analogue satellite receiver and
a Video recorder
VCR

GB 8
Connect an RCA/Cinch stereo cable from the AUDIO L R
sockets on the Mediamaster to the LINE, AUX, SPARE or
EXTRA input sockets on our Hi Fi s stem.
 Remove the cover on the batter compartment at
the bottom of the remote control handset.
 Insert the 2 x AAA (1,5 V) batteries, as shown in
the diagram, taking care to observe the + and -
markings indicated inside.
 Replace the cover.
Please read this information concerning menus.
A menu is a field of text shown on the TV screen. These menus contain different kinds of information
and give the possibilit to select between alternatives. At the bottom of the screen ou will normall
also see a short explanation of our options. A menu ma contain several lines. Selectable lines are
highlighted. Non-highlighted lines are not selectable.
Connecting to Hi Fi system
Preparing the remote control
efore you continue

GB 9
This section describes how to operate the Mediamaster using the buttons on the remote control.
Some of the functions can also be carried out using the buttons on the front panel.
Switch the Mediamaster in and out of standb mode.
EXIT TV Return to the viewing mode from a menu without storing settings
(in menu mode).
Switch between TV or Radio (in viewing mode).
Turn the sound off/on (mute).
Adjust the volume of digital programmes.
The Mediamaster s maximum level is controlled b the TV s present volume setting.
0 — 9 Change channel and to select individual menu options.
Note:If 0 is entered as the first digit, the TV Release functionalit is activated (see below)
0 TV Release. To switch between digital TV/Radio, analogue TV and analogue satellite TV
and VCR, when our s stems are connected b SCART cables.
Info. To displa short and extended information (if transmitted)
about current and next programmes.
ACK Go back one level in the menus without storing settings.
TEXT Select teletext information. Press to enter Teletext
(if available).
MENU Show the Main Menu screen.
GUIDE Obtain a list of present and following programmes for the
available channels. This information is onl shown if our
Service Provider transmits programme information
(EPG information).
P+ P- Change channels up and down b one unit.
Change page in a menu/list/text if more than one page
is available. To browse through teletext histor .
Move up/down in the menus and to change channels.
Change settings in menus
OK Confirm choices and selection of a highlighted item.
To displa the TV/Radio channel list.
(Red) Reserved for future application.
OPTION (Green) To select service options in viewing mode.
FREEZE (Yellow) To select the freeze function.
Press once to freeze the screen picture.
Press an other ke to go to normal mode again.
(Blue) To toggle between present and previous TV/Radio channels.
REMOTE CONTROL

GB 10
Once ou have correctl connected the Mediamaster, ou also have to perform some asic
Settings . During this procedure, helpful information is displa ed at the bottom of the menus.
Please note!
The OK button alwa s confirms a selection within these menus, and pressing it will take ou to the
next step in the installation process. However, and this is important, often more than one value has to
be entered in a menu. First, perform all necessar settings on the different lines. Then, confirm them
all simultaneousl b pressing OK.
You can alwa s go back to the previous menu b pressing the ACK button.
Use the buttons to move upwards and downwards from one line to another. Use to change settings.
You can also use the numeric buttons on the remote control to select a line in a menu and to enter
numeric values.
This procedure is necessary only if your Mediamaster is connected to the TV with an RF
cable.
To tune our TV to the RF signal ou might also need our TV manual in addition to this manual. The
steps below explain what to do if ou have been unable to use SCART cables in our connection.
 Plug in our Mediamaster.
Tuning your TV to the Mediamaster.
 Select a channel number on the TV that is not currentl used for other TV channels.
 Follow the instructions in our TV manual to tune the TV channel selector to UHF channel 43 (this
is the Mediamaster s factor preset UHF channel). If ou are alread using this channel, select
another non occupied UHF channel between 21to 69 on the TV.
 When ou have correctl changed the UHF channel number ou will see the Welcome menu on
the TV screen. If there is interference from other channels ou will have to change the chosen
UHF channel.
 Follow the instructions in our TV manual to store this UHF channel as the channel used b our
Mediamaster. You will have to select this channel when ou want to watch digital TV/Radio
channels.
 Once the welcome message is visible, press the OK button on the Mediamaster s remote control
to start the installation procedure.
If for some reason ou have to change the RF channel later, ou can do this b using System
Settings menu further on in this manual. If ou have a VCR connected it must be tuned to a
different UHF channel (between 21 to 69) than the Mediamaster.
You ma now proceed to The Welcome Menu.
ASIC SETTINGS
Tuning procedure when RF connections are used

GB 11
To install the Mediamaster properl ou have to adjust a few
settings. You will alwa s be guided b the information at the
bottom of the menus. When ou have finished the final part of
the setup procedure ou can start watching TV channels and
listening to radio channels. Now ou should have the
Welcome Menu on the TV screen. Press the OK button to
proceed.
Select the menu language that ou desire. This will define the
language shown in the menus. This will also be the main
language for all the other parts such as audio and subtitling
languages. Press the OK button to proceed.
Installation
In order to configure our equipment (satellite dish and LNB)
ou will need to use the following menus.
The LNB is the receiving unit, which is mounted on the satellite
dish. For the following setup procedure ou have to know the
Local Oscillator (LO) frequenc valid for our LNB(s).
Highlight Antenna Satellite Configuration and press the OK
button. You can configure the antenna for each satellite from
this menu.
Antenna Alternative:
Select an Antenna alternative from 1 to 16 . Please note, that
the parameters in the menu are pre-programmed, but ou can
change an of them to suit our combination.
The Welcome Menu
Language Settings
Antenna Satellite Configuration

GB 12
Satellite name: From here ou can select a name for the configuration.
Switch Type:
There are in principle two kinds of external DiSEqC switches on the market at present. One for
connection of two LNBs. The other one for connection of up to 4 LNBs.
If ou have the other switch, defined as DiSEqC, Level 1 or 2 on the market, select DiSEqC 1, 2,
(3 or 4) , for each LNB connected to respective inputs on this switch.
LN Type:
Selection is possible for different kinds of LNBs. Select the frequenc for the LNB, which is valid for
our combination. You ma also enter a value with the numbered buttons on the remote control. The
LNB alternatives are: Universal (which is the most common), 5.150 , 9.750 , 10.000 , 10. 050 ,
10.600 , 10.750 , 11. 200 , 11. 475 .
If ou have special LNB t pe, ou should select User Define on this menu. And ou can enter a new
LNB frequenc in the following LNB Frequenc menu.
LN Frequency:
You can enter a special LNB frequenc , which is not presented in the LNB T pe list as above.
22 KHz Tone Switch:
If ou have connected to a Dual LNB or two antennas connected to a 22 KHz tone switch box, set it
to Enable the 22 KHz tone switch.
When ou have finished the settings in this menu, press the OK button to save the parameter.
Press ACK to continue with the channel search set-up
(You can also recall this menu later. From the Main Menu; select Installation and then Antenna
Satellite Configuration ).
Highlight Automatic Channel Search using the down arrow
button on the remote control. Mediamaster has pre-
programmed Antenna/Satellite parameters for Astra, Hot ird,
Arabsat, NileSat, PanAmsat 4, AsiaSat 2, AsiaSat 3,
TurkSat 1 , TurkSat 1C and Other 1 to Other 7.
Antenna Alternative: Select the option, 1 to 16 , that
corresponds to our antenna s stem.
Predefined Channel: Each antenna alternative has one or two pre-programmed channel
parameters. Choose a channel from which ou want to start the channel search. Normall , each of
the pre-programmed channels gives the same result.
Search Type: Select Free Channels in order to search for free channels onl .
Select All Channels in order to search all channels on the satellite.
Automatic Channel Search

GB 13
You can use manual channel search if ou want to add new
channels later. For example If ou have a special antenna
configuration which is not assigned in the Antenna
alternative menu, ou can add new channels using the
manual channel search function. When ou perform a
Manual Search ou first need to enter some parameters for the
channel search to work. The information ou need to enter in
this menu is available in magazines covering satellite TV
reception, on the Internet or from our Service Provider.
Antenna Alternative: Select Antenna Alternative 1 to 16 that corresponds to the antenna which
ou wants to use for the search.
Transponder Freq (MHz): Specif the frequenc in GHz. using the numbered buttons on our
remote control. If ou enter the wrong number, erase it with the left arrow button.
Polarization: Select polarization; Horizontal or Vertical .
Symbol Rate (Msym/S): Enter the rate with the numbered buttons.
FEC: Enter the appropriate Forward Error Correction (FEC) value or select Auto .
Network Search: Select: Yes to search from all
transponders used b a specific Service Provider.
(Yes is the default setting). Select No to search onl from
the transponder that ou have entered on the line
Transponder Frequency . (Useful if ou do not want to
search through all transponders for a specific program
distributor).
B pressing the OK button ou can now enter the channel
search menu where the Mediamaster starts to search for
channels from the satellite.
The following will describe the basic functions of our Mediamaster while watching TV or listening to
radio channels.
Sometimes the information may not be displayed as illustrated. Many of the functions
described here are dependent on the Service Provider and/or can only be used if they are
included in the transmitted programme information.
Please note that during the Channel Search procedure, the Mediamaster has downloaded ALL
available channels. This ma include channels from various Service Providers, also those to which
ou normall do not have access. If ou select a programme to which ou do not have access, ou
will get the message Service is scrambled or not running on the screen.
Manual Channel Search
VIEWING TV
General Information

GB 14
If ou have a TV set with a 4:3 picture format, and the transmission is in 16:9, ou can select 4:3
(Pan & Scan) or 4:3 (Letterbox) to change displa format. 4:3 (Pan & Scan) will fill up the
screen verticall , but cut off some information from the left and right sides of the picture. 4:3
(Letterbox) will give a complete picture, but leave black areas at the top and bottom.
You can select the TV screen format in the System setting menu which is a subsidiar of the User
preference menu.
To start the Mediamaster from stand-b mode, press the button or one of the numbered buttons
on the remote control. It is also possible to start b pressing the button on the front of the
Mediamaster. Put the Mediamaster into stand-b b pressing again the button again.
In stand-b mode the displa will show the correct time. During viewing the channel number will also
be displa ed.
Change channel with the numbered buttons or with the up/down buttons on the remote control.
You can also use the buttons up/down on the front panel of the Mediamaster.
You can also select TV (Radio) channel in the TV (Radio) channel list. See the List of TV Channel
and List of Radio Channel of page 15 and 16.
Ever time ou change channel ou will receive information for
4-5 seconds about the current programme. This information
includes: Channel number, name, programme title, and time for
present and following programmes. Press i while watching a
channel. If our Service Provider transmits programme
information ou will see: Correct time, a small amount of
information for the current and next programme, the name and
number of the channel, and finall the start and finish time for the programme.
If ou want to get more detailed information, press i once more while the information box (banner)
is shown. You will get extended information (if transmitted) about the current or next programme.
TV Screen Format
Start/Stop Watching TV
Select Channel
Program Information. The i utton

GB 15
By pressing the GUIDE button you obtain access to the
TV Guide which gives the titles of the current programmes on
the different channels. By pressing the LEFT or RIGHT button
you also can also obtain information about the next
programme. The minimized viewing window also helps you to
select channels and information. Use the Up/Down buttons to
move the cursor to different programme areas. ou can obtain
extended information for a programme by pressing the i button.
The display on your Mediamaster and on the TV screen will
show the name of the audio channel you are listening to. While
in audio mode, you can press the i button to get extended
information (if transmitted) about the audio programme.
Return to TV mode by pressing the TV button again.
Increase or decrease the sound level by pressing the + and
- buttons. A control bar will be displayed at the top of the
screen during level adjustment. (The max. level for volume is
the current volume setting on the TV set). Please note, that the
volume adjustments also change the volume level of to your
VCR during recording. It is possible to turn the sound on and
off with the button. Sound off is indicated with the same
symbol on the screen. If you turn the volume off with this
button, it does not affect the volume of the VCR during recording.
The current volume level will be remembered when you go
to standby mode.
While viewing the TV you can see a programme
list on the screen by pressing the OK button. ou can change
to another channel by pressing the UP/DOWN buttons and
then pressing the OK button. To move faster (8 channels at a
time) between channels you can also use the
DOUBLE ARROW buttons.
TV Guide
The R dio Button
Volume Level
List of TV Ch nnels

GB 16
While listening to radio Programmes ou can see a programme
list on the screen b pressing the OK button. You can change
to another channel b pressing the UP/DOWN buttons and
then pressing the OK button. To move faster (8 at the time)
between the channels ou can also use the DOU LE ARROW
buttons.
With a Video Cassette Recorder (VCR) connected ou can watch/record video tapes.
If our VCR is connected with a SCART cable and ou press the start button on the VCR, the
pla back will start and interrupt the TV programme from the Mediamaster.
To watch TV programmes again, press the TV button or stop the VCR.
Please note, that during the recording of a programme, everything shown on the screen will be
registered! For example: If ou call up a Menu from the Mediamaster on the screen, the menu will be
recorded!
Pressing the TEXT button once while watching TV enables the teletext output to the TV.
To enable the teletext displa on the TV, press the Teletext button on the TV s remote control.
This is onl possible if more than one subtitling language is being transmitted. Please refer to the
instruction manual of our TV for the teletext function. Exit the menu b pressing the TV button.
Press the MENU button and ou will get the Main Menu on the
TV screen. Press the EXIT button to leave the menu.
If ou select one of the highlighted titles and press the OK
button, a submenu will be shown on the TV screen. From a
submenu ou can adjust settings to our own requirements.
List of Radio Channels
Video Recorder
Subtitling and Teletext. The TEXT utton
SETTING FROM THE MAIN MENU

GB 17
TV/Radio Channels will show a list with the names of the
different channels. To move faster within the list, use the
DOU LE ARROW buttons. Press OK to enter a marked
channel.
These guides will give ou an overview of programme
information from the TV/Radio channels. Step to different
channel numbers with the UP/DOWN buttons. If ou stop on a
highlighted line and press OK, ou will exit the menu and enter
the highlighted channel. Select information about the next
programme with the RIGHT button. Use the i button to get
extended information about a marked programme.
Please note, that information will onl be shown if it is included in the transmission.
From this menu, ou can rename favorite lists, add channels,
remove channels and arrange the channels in a preferred
order.
The All TV list displa s all channels, which ou captured from
the channel search operation in the installation menu
The All TV list can contain hundreds of channels. B creating
our own favorite lists ou can make channel handling a bit
more convenient.
TV Channels and Radio Channels
TV Guide and Radio Guide
Edit Channels

GB 18
If ou have created several Favorite lists ou can
determine the sequence in which the lists will appear. To
rearrange channels, select the list which ou want to
move using the OK button. Move the channels to the desired
position using the UP/DOWN button and press OK.
You can change the list name with the virtual ke board
on the screen. T pe in the text ou want using the remote
control arrow ke s. Please note that the All TV , All Radio ,
Free TV and Free Radio can not be changed.
Delete the existing characters b pressing OK on the left arrow
ke of the ke board. Select the characters using the LEFT and
RIGHT buttons. Press the OK button to enter the text selected.
To save the renamed list, press the ACK button.
To select various characters, press OK on the page UP/DOWN box of the ke board.
From here ou can create our own favorite lists, containing the
channels ou watch most frequentl . You can give each list a
specific name in the Rename List menu. When a favorite list is
selected, ou see onl those channels defined in the list. You
can add channels to our Favorite Lists from the All TV , All
Radio , Free TV and Free Radio list. A channel is added b
pressing the OK button. The V marking to the right on a line
contains added channels.
To get to this menu ou need an access code. The default
access code is 1234 . From here ou can lock (and later
unlock) channels in an of the lists in order to prevent e.g. our
children from watching. Select the channel ou want to lock
and press the OK button. A locked channel will be marked with
a padlock s mbol. Repeat the procedure for each channel ou
want to lock. When ou lock a channel in an list, the channel
will automaticall be locked in all other lists When watching TV, ou will be asked to enter our
access code before ou can watch a locked channel.
Rearrange List
Rename List
Add Channels
Lock Channels

GB 19
You can arrange the order of channels within our favorite lists.
To rearrange channels, select the channel which ou want to
move using the OK button. Move the channels to the desired
position using the UP/DOWN button and press OK.
From here, when the All TV list is selected in the Edit
Channels menu, ou can remove channels.
Please note. Channels deleted this way will be
permanently removed. The only way to get them back is to
perform a new channel search.
To remove channels:
Select the channel that ou want to delete and press OK. You
will be asked if ou reall want to remove it. If so confirm b
pressing OK once more. If not, press ACK.
From here ou can change the menu language. You also have access to the Parental Control and
the Appearance menus.
B pressing OK on the line Parental Control ou will be
requested to enter our access code. (Personal Identification
Code).
This code is set to 1234 b the factor . You will then get the
menu from where ou can lock some functions in the
Mediamaster.
Receiver lock
If ou select On , ou will have to enter the access code ever time ou start the Mediamaster from
stand-b .
Lock Installation Menu
If ou select On , ou will have to enter the access code ever time ou enter the installation menu.
Age Limit
If ou want ever bod to have access to all available t pes of programmes, select Off .
If ou select On , ou ma block programmes unsuitable for children. Select an age limit between 4
and 18 ears on the line that appears.
However, ou should be aware that not all Service Providers have the necessar codes for these
functions implemented in their transmissions.
Rearrange Channels
Remove Channels
USER PREFERENCES
Parental Control

GB 20
Change access code
From here you can change the access code from the standard 1234.
DO NOT FORGET IT! Without it you do not have access to any of the functions where the code
is required!
If you forget it, you have to contact an Authorized Nokia Service Center to get help.
From here ou can change the language for the menus, main
audio language and alternative audio language.
From here ou can adjust settings concerning our TV.
TV Screen Format: Select our TV screen format.
The 4:3 format is the standard format for most TV screens.
Select 16:9 for a wide screen TV.
Output Selection: If the teletext function does not work when
watching channels from an analogue satellite receiver
connected to the Mediamaster, change this setting from RG to Composite .
UHF Channel Number: Select this alternative if ou have to change the RF channel.
If ou change the RF channel number, ou must also change it to the same value on the TV. If ou
do not, the picture will become black.
RF Modulator Type: If the Mediamaster is connected to the TV b an RF cable, ou can select the
RF modulator t pe. The RF Modulator affects a channel s audio. If ou get picture but no sound, the
RF modulator selection might be wrong. Select UK (PAL I) if the Mediamaster is used in the UK.
Select Normal if it is used elsewhere.
Information ox Timeout (secs): When ou switch channels, an information banner will be shown
for a few seconds. You can select for how long the banner will be shown.
Display Volume Indicator: Select whether or not ou want the volume bar to appear on the screen
when ou change the volume.
Date Setting (dd/mm/yyyy): Used to set the current date, month and ear.
Time Setting: Adjust the clock.
GMT Offset: Adjust the time difference in our countr .
Language Settings
System Settings