Nokia MEDIAMASTER 9800 S User manual

Owner’s Manual
MEDIAMASTER
9800 S

GB
Hereby, Nokia declares that this digital receiver,
Mediamaster 9800 S, is in conformity with essential
requirements and other relevant provisions of Directive
1999/5/EC. This Terminal Equipment is intended for
connection to the analogue Public Switched Telephone
Networks (PSTNs), in which network addressing, if
provided, is by means of Dual Tone Multiple Frequency
(DTMF) signalling.

GB 3
MEDIAMASTER 9800 S
Contents
General information 4
For your safety 4
Remote Control 5
Front and rear panel 6
Viaccess smartcard 7
The CA module with its smartcard 7
Preparing the Remote Control 8
Connecting the Mediamaster to the dish 8
Connecting the Mediamaster 9
Connecting to the TV 9
Connecting a TV and VCR 9
Connecting an analogue satellite receiver
and a VCR 10
Nokia smart priority switch 10
Universal Twin LNB 10
Connecting a HiFi system 10
Switching on for the first time with
SCART connections 11
Tuning procedure when RF connections
are used 11
First time installation 12
General information 12
The Welcome menu 12
Language 12
RF Modulator type 13
Antenna/Satellite selection 13
Common menus 13
Antenna adjustment and signal check 14
About signal strength (AGC)
and signal quality (SNR) 14
Antenna/Satellite selection 15-16
Multisatellite/DiSEqC switch configuration 17
Antenna motor installation 18-22
Channel search progress 22
Time adjustment 22
Viewing mode 23
General information 23
Programme information 23
The “i” (information) button 24
Guide 24
List of TV and radio channels 25
Options (green button) 25
TV release (0) 26
Video recording 26
The TEXT button (Teletext) 26
EXIT TV 26
Main menu 27
General information 27
TV and radio channels 27
Edit channels 27
Update channels 31
Guide 32
System configuration 32
Channel search 32
Edit satellites 34
Antenna/Satellite configuration 36
TV settings 36
Time adjustment 36
Receiver upgrade 37
Reinstall 37
User preferences 37
Language preferences 37
Parental control 38
Appearance preferences 39
System information 40
Conditional Access 41
Viaccess embedded 41
Smartcard settings 41
Common Interface (CI) 41
Glossary 42
Problem solving 43
Front panel display 44
Technical specifications 45
Menu screen structure 46
Nokia and Nokia Connecting People are registered trademarks of Nokia
Corporation. Other product and company names mentioned herein may be
trademarks or trade names of their owners.
Nokia operates a policy of continuous development. Therefore we reserve the
right to make changes and improvements to any of the products described in
this manual without any prior notice.
Copyright © 2001. Nokia Corporation.
All rights reserved.

GB 4
GENERAL OPERATION OF THE MEDIAMASTER
• Allow clear space around the Media-master for
sufficient ventilation.
• Do not cover the Mediamaster or place it on a
unit that emits heat.
• Use a soft cloth and a mild solution of washing-
up liquid to clean the casing.
• Never allow liquids, spray or other materials to
come into contact with the inside of the
Mediamaster.
• Do not connect or modify cables when the
Mediamaster is plugged in.
FOR YOUR SAFETY
• Do not remove the cover.
• Do not allow the unit to be exposed to hot, cold
or humid conditions.
• Service should be carried out only at a Nokia
Authorised Service Centre.
• Please note that the only way to isolate the
Mediamaster completely from the mains supply
is to unplug the mains lead!
Throughout this manual you will notice that the everyday opera-
tion of your Mediamaster is based on a series of user friendly on-
screen displays and menus. These menus will help you get the
most from your Mediamaster, guiding you through installation,
channel selection, viewing and many other functions.
All functions can be carried out using the buttons on the remote
control, and some of the functions can also be carried out using
the buttons on the front panel.
Please be aware that new software may change the functional-
ity of the Mediamaster.
Should you experience any difficulties with the operation of your
Mediamaster, please consult the relevant section of this manual,
including the Problem Solving, or alternatively call your dealer or
a customer service adviser.

GB 5
Switch the Mediamaster in and out of standby mode.
EXIT TV Return to the viewing mode from a menu without storing
settings (in menu mode).
Switch between TV or Radio (in viewing mode).
Turn the sound off/on (mute).
- + Adjust the volume of digital programmes.
The Mediamaster’s maximum level is controlled by the TV’s
present volume setting.
0 - 9 Change channel and to select individual menu options.
Note: If 0 is entered as the first digit, the TV Release func-
tionality is activated (see below).
0 TV Release. To switch between digital TV/Radio, analogue
TV and analogue satellite TV and VCR, when your systems
are connected by SCART leads.
Info. To display short and extended information (if transmit-
ted) about current and next programmes.
BACK Go back one level in the menus without storing settings.
TEXT Select teletext information.
Press to enter teletext (if available).
MENU Display or exit from the ”Main Menu” screen.
GUIDE Obtain a list of present and following programmes for the
available channels. This information is only shown if your
Service Provider transmits programme information (EPG
information).
P+ / P - Change channels up and down by one unit.
Return to TV mode from an “Open TV” application.
Change page in a menu/list/text if more than one page is
available. To browse through teletext history.
▲ ▼ Move up/down in the menus and to change channels.
Change settings in menus.
OK Confirm choices and selection of a highlighted item.
Display the TV/Radio channel list.
(Red) Download an “Open TV” application.
OPTION (Green) Select service options in viewing mode.
OPTION + code will open locked channels.
FREEZE (Yellow) Select the freeze function.
Press once to freeze the screen picture.
Press any other key to go to normal mode again.
(Blue) Toggle between present and previous TV/Radio chan-
nels.
This section describes how to operate the Mediamaster using the buttons on the remote control.
Some of the functions can also be carried out using the buttons on the front panel.
REMOTE CONTROL

GB 6
Slot
for a CA module
with a Smartcard
to put the Mediamaster
in and out of standby
mode
to move up/down in
the menus and to
change channels.
Display
Shows channel number, error
messages and remote control
commands. In standby mode
the time is shown.
Front Panel
Slot
for a Smartcard
Button
Push the button to release
an inserted CA module
AUDIO L R
phono connectors
Stereo outputs for
connection to a HiFi
system
TV SCART
for connection
to the TV
AUX SCART
for connection to a VCR,
or an analogue satellite
receiver
* LNB cable also feeds the LNB with a supply voltage of 13/
18 V (V/H polarisation) and a 0/22 kHz signal (bandswitch).
Max LNB current 500 mA.
DIGITAL AUDIO
phono connector
S/PDIF output for
connection to
a HiFi system
95-250 V AC
50-60 Hz.
Connection for
the enclosed
mains cable.
ANTENNA *
Satellite dish
input (F-connec-
tor)
Rear Panel
SERIAL PORT
to read and load
data information
TV AERIAL
for a terrestrial (con-
ventional) TV aerial
TV/VCR
for an RF-cable to
the aerial input of
the TV or VCR
FRONT AND REAR PANEL

GB 7
Viaccess smartcard
Only for Pay-TV services coded with the Viaccess CA system.
•Insert your Smartcard fully into the left slot behind the lid of
the front panel of the Mediamaster. The gold chip should face
downwards and inwards.
PIN Code
The Smartcard is loaded with a 4-digit code, also called a PIN code
(Personal Identification Number).
The code is essential in order to access future services offered
by the Service Provider.
ABOUT THE SMARTCARD AND CA MODULE
To be able to receive scrambled digital satellite channels you will
need a Smartcard and/or a Common Interface CA (Conditional Ac-
cess) module *from the Service Provider of your choice.
The Service Provider is the programme distributor.
If you are subscribing to services from more than one Service
Provider, you might have to change between different Smart-
cards and/or CA modules.
Please note that a Smartcard and CA module may only be valid
for a single Service Provider and due to this, a specific range of
channels.
The Smartcard and the CA module may also provide access to
special menus not described in this manual. If so, please follow
the instructions from the Service Provider.
Only ”free to air”channels are available without the Smartcard
and/or the CA Module.
Note: The Smartcard and/or the CA module are distributed by
your Service Provider.
After inserting the card, leave it in the slot permanently. Do not
remove it again, unless your Service Provider asks you to do so.
This is important, because if your Service Provider wants to
download new information to the Smartcard, the card has to be
in the slot.
*Only use a DVB Standard Common Interface CA Module
The CA Module with its smartcard
•Follow the instructions from your Service Provider concerning
the Smartcard and/or CA module.
•Insert the CA module fully into the slot behind the lid of the
front panel of the Mediamaster.
•Press the grey button on the front panel if you need to remove
the CA module.

GB 8
The box for your Mediamaster should contain the
following items:
•the Mediamaster
•a remote control with 2 AAA batteries
•a SCART lead (fully featured 1,0 metre)
•an aerial/RF lead (double screened 1,5 metres)
•an Owner’s Manual (this document)
•a Software License agreement
•mains cable
INSTALLATION OF THE MEDIAMASTER
About the SCART sockets
The rear panel of the Mediamaster is equipped with 2 SCART
sockets (see diagram). When you connect other products to
any of these sockets, always use fully featured SCART leads
(as supplied). There are “less well specified”SCART leads on the
market and picture quality could be reduced if you use them. SCART socket
SCART lead
Owner’s manual License
agrement
RF lead
Preparing the Remote Control
•Remove the cover on the battery compartment at the bottom
of the remote control.
•Insert the 2 AAA (1,5 V) batteries, as shown in the diagram,
taking care to observe the +and -markings indicated inside.
•Replace the cover.
Installing the Satellite Dish
•See the ”Fitting instructions for satellite dish”on how to in-
stall the dish.
•Connect the coaxial cable, with F-connectors fitted, from the
LNB on the satellite dish to the socket marked ”ANTENNA”on
the rear panel of the Mediamaster (or e.g. a DiSEqC switch).
Connecting the Mediamaster to the Dish
If you need to fit the F-connectors onto the cable
•Prepare each end of the cable as shown in the diagram. You
will need to fold back the outer braid (as shown).
•Slide the F-connector onto the cable, then turn it clockwise
until it grips the braid.
•Ensure that 3 mm of the core is protruding from the end of the
connector.
8 mm
15 mm
3 mm
F-connector
Mains cable

GB 9
Connecting to the TV
•Connect the SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
•Connect an RF lead from the TV/VCR output on the Media-
master to the RF input socket on the TV.
•Connect the TV aerial to the TV AERIAL input socket on the
Mediamaster.
Connecting the Mediamaster
There are many different types of TV/VCR and other equipment
that you can connect to the Mediamaster.
In this manual you will see some of the most common ways to
connect your equipment.
If you use RF leads you will have to tune your TV and VCR to the
Mediamaster output channel (see page 11).
If you have problems with your connections and need help, con-
tact your dealer or Service Provider.
RF
SCART
Connecting a TV and VCR
Refer to your VCR’s manual for full instructions.
•Connect one SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
•Connect another SCART lead between the VCR
and the AUX SCART socket on the
Mediamaster.
•Connect the RF lead from the RF output on the
VCR to the TV aerial input on the TV.
•Connect the TV aerial to the RF input socket on the VCR.
VCR
Mediamaster
SCART
SCART
RF
If your TV has a SCART socket, but your VCR does not
•Connect a SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
•Connect an RF lead from the RF output on the
VCR to the TV aerial input on the TV.
•Connect an RF lead from the TV/VCR output on
the Mediamaster to the RF input socket on
the VCR.
•Connect the TV aerial to the TV AERIAL input
socket on the Mediamaster.
VCR
Mediamaster
SCART
RF
RF
INSTALLATION OF THE MEDIAMASTER

GB 10
Connecting an Analogue Satellite Receiver and a VCR
Nokia Smart Switch
Connecting a HiFi System
•Connect an RCA/Cinch stereo cable from the AUDIO L R sock-
ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA
input sockets on your HiFi system.
•If available you can connect an RCA/Cinch single cable from
the DIGITAL AUDIO socket on the Mediamaster to your HiFi
or Dolby Pro Logic system.
Note: To avoid interference you must use a screened audio
cable.
VCR
•Connect a SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
•Connect a SCART lead between the VCR and the AUX SCART
socket on the Mediamaster.
•Connect an RF lead from the RF output on the VCR to the TV
aerial input on the TV.
•Connect an RF lead from the RF output on the
Analogue receiver to the RF input socket on the
VCR.
•Connect the TV aerial to the RF input socket on the Analogue
receiver.
In order to switch the signal from the dish between the ana-
logue and digital receivers, you need a Nokia Smart switch (at
A B in the diagram) or a Universal Twin LNB.
With Nokia Smart
switch
Analogue receiver
Mediamaster
SCART
RF
Nokia Smart switch
•Connect a coaxial cable between output A on the NOKIA Smart
switch (accessory) to the LNB socket on the analogue
receiver.
•Connect a coaxial cable between output B on the NOKIA Smart
switch to the ANTENNA socket on the Mediamaster.
The analogue receiver must be switched to OFF (standby) when
you want to watch digital satellite channels from the
Mediamaster.
INSTALLATION OF THE MEDIAMASTER

GB 11
This procedure is necessary only if your Mediamaster is con-
nected to the TV with an RF lead.
To tune your TV to the RF signal you might also need your TV
manual in addition to this manual. The steps below explain what
to do if you have been unable to use SCART leads in your con-
nection.
•Plug in your Mediamaster.
Tuning your TV to the Mediamaster
•Select a channel number on the TV that is not currently used
for other TV channels.
•Follow the instructions in your TV manual to tune the TV chan-
nel selector to UHF channel 43 (this is the Mediamaster’s fac-
tory preset UHF channel). If you are already using this chan-
nel, select another non occupied UHF channel between 21to
69 on the TV.
•For example, if you select UHF channel 45 on your TV, you
must change your Mediamaster to the same channel.
Use the or buttons on the front panel of the Mediamaster,
or on the remote, to change to the corresponding channel. You
will see the UHF channel number displayed on the front panel
of the Mediamaster.
•When you have correctly changed the UHF channel number
you will see the ”
Welcome ”menu on the TV screen.
If there is interference from other channels you will have to
change the chosen UHF channel.
•Follow the instructions in your TV manual to store this UHF chan-
nel as the channel used by your Mediamaster. You will have to
select it when you want to watch digital TV/Radio channels.
•Once the welcome message is visible, press the OK button
on the Mediamasters remote control to start the installation
procedure.
If for some reason you have to change the RF channel later,
you can do this by using TV settings menu further on in this
manual.
If you have a VCR connected it must be tuned to a different
UHF channel (between 21 to 69) than the Mediamaster.
You may now proceed to “First Time Installation.”
Tuning Procedure when RF Connections are Used
•Plug in your Mediamaster
•Now you will see the ”Welcome”menu on the screen.
•Press OK on the Mediamaster remote control to start the In-
stallation procedure.
You may now proceed to “First Time Installation.”
Switching on for the First Time with
SCART Connections
INSTALLATION OF THE MEDIAMASTER

GB 12
Language
Select the desired menu language.
This will also be the main language for subtitling and audio.
To reach the Norwegian, Finnish, Russian, Turkish and the Greek
language alternative, you first have to press the double arrow
down button on the remote control.
General Information
Once you have correctly connected the Mediamaster, you also
have to perform a “First Time Installation.”
During this procedure, helpful information is displayed at the bot-
tom of the menus.
Please note!
The OK button always confirms a selection within these menus,
and pressing it will take you to the next step in the installation
process. However, and this is important, often more than one
value has to be entered in a menu. First, perform all necessary
settings on the different lines. Then, confirm them all simultane-
ously by pressing OK.
You can always go back to the previous menu by pressing the
BACK button.
Use the buttons to move upwards and downwards from one
line to another. Use to change settings.
You can also use the numeric buttons on the remote control to
select a line in a menu and to enter numeric values.
FIRST TIME INSTALLATION
The Welcome Menu
This picture indicates that you have started the installation pro-
cedure.
Press the OK button to proceed.

GB 13
Antenna/Satellite Selection
Select one of the alternatives from line 1 to 4 if you have a sin-
gle antenna equipped with one LNB for receiving signals from
either ASTRA, HOTBIRD, SIRIUS or THOR.
Select one of the alternatives from line 5 or 6 if you have one
antenna with two LNBs or two antennas with one LNB on each
for receiving signals from the combination ASTRA/HOTBIRD or
THOR/SIRIUS. In these cases you also need a DiSEqC switch.
For any other antenna/LNB combination, select alternative 7.
Alternatives 1-6 requires the use of a Universal LNB(s.)
RF Modulator Type
If the Mediamaster is connected to the TV with a RF cable, you
must select the right RF modulator alternative, which is depend-
ent on the country where the Mediamaster is being used.
Select “Normal (PAL B/G)”when the box is used outside the
UK.
Select “UK (PAL I)”when the box is used inside the UK.
If you get picture but no sound, the RF modulator selection might
be wrong.
FIRST TIME INSTALLATION

GB 14
FIRST TIME INSTALLATION
*)About Signal Strength (AGC)
and Signal Quality (SNR)
The different signal indicators at the top of the menu provide in-
formation about two things:
AGC: The AGC, shown with a red bar, will indicate the average
strength of any incoming signal, digital as well as analogue.
SNR: When a programme from a satellite channel shows up on
the screen, the indicator bar will change from showing
AGC to showing SNR. The bar is now red, yellow and
green, and will indicate the signal quality from that specific
channel.
Antenna Adjustment and Signal Check
Pressing OK from the selected alternative in the previous menu
will display the Antenna Adjustment menu (shown to the right)
on the screen.
For each satellite, (e.g. ASTRA, HOTBIRD, SIRIUS, THOR), up to
4 different channels are preprogrammed and shown in the menu.
When you adjust the antenna, your Mediamaster will use the
marked channel to find signals from a satellite. (You can select
another channel with the buttons.)
1Adjust the antenna towards the desired satellite until you have
a high value on the Signal Strength (AGC) *)indicator (the red
bar at the top of the menu.)
2When the antenna is correctly positioned towards the satel-
lite and the signal strength is as good as possible, press OK.
If you have found a digital signal you should then normally get
a picture from the marked channel.
3The bar at the top of the menu will now change to a red/yel-
low/green Signal Quality (SNR) *) indicator for that specific
channel.
If you do not get a picture, you may be tuned to an analogue sig-
nal source. Another reason could also be that the antenna is po-
sitioned towards the wrong satellite.
Press the BACK button and start from point 1again.
The reason could also be that the marked channel is not trans-
mitting at the moment. If so, select one of the other prepro-
grammed channels in the “Signal Quality”menu with the
buttons.
When you have picture from a TV channel, press OK. The Media-
master automatically starts searching for and downloads chan-
nels from the satellite. Please refer to page 22.
(If you have a good indication in the signal quality menu, but no
picture from any of the channel alternatives, try proceeding with
the channel search anyway by pressing OK).
OK
OK

GB 15
FIRST TIME INSTALLATION
Select one of these alternatives when you have a single antenna
equipped with 2 LNBs, or two antennas with one LNB on each,
and want to watch channels from ASTRA/HOTBIRD or THOR/
SIRIUS.
In this case you must first connect the LNBs to an external switch
since there is only one antenna input on the Mediamaster. Once
installed the switch automatically selects the correct LNB for the
selected channel.
This external switch is better known as a DiSEqCTM switch. Since
the switch can be located close to the LNBs, you only need one
cable down to the Mediamaster.
Connection of a DiSEqC switch:
•Connect the cable from the LNB intended for channels from
ASTRA (or THOR) to the connector marked LNB 1 (A) on the
switch,
•and the cable from HOTBIRD (or SIRIUS) to the connector
marked LNB 2 (B).
•Connect the antenna cable to the connector marked Receiver
OUT on the switch. Connect the other end of this cable to the
ANTENNA input in the rear of the Mediamaster.
Please follow the instructions on page 14, “Antenna Adjust-
ment and Signal Check.”
The difference in this case is that you now will have channel al-
ternatives from two satellites.
Adjust the antenna until the indication value is as good as possi-
ble for both satellites.
Select one of the alternatives ASTRA, HOTBIRD, SIRIUS or
THOR when you have a single LNB pointed towards any of these
satellites.
Then follow the “Antenna Adjustment and Signal Check”in-
structions on the previous page.
Line through on the Antenna Sat-
ellite Selection Menu
1 4
Line and on the Antenna Satellite
Selection Menu
5 6

GB 16
Line 7 on the Antenna Satellite Selection
Menu
This selection is necessary only if your satellite choice differs
from the preprogrammed satellite alternatives (line 1-4) in the fol-
lowing ways; if you do not use a universal LNB or when you have
more than two LNB’s.
You also must select this alternative when your antenna is con-
trolled by motor (ref. to page 18.)
One Antenna/One LNB Configuration
Select this alternative if you have one LNB mounted on the an-
tenna and you want to select another, not preprogrammed, sat-
ellite.
LNB Type
Select the local oscillator (L. O.) frequency valid for the present
LNB. The most common values, including Universal LNB, are
selectable with the
buttons.
You can also enter a value with the numeric buttons when the
symbol for the remote control is visible on the line.
Satellite
Select one of the preprogrammed satellites.
Predefined Channel
Select one of the preprogrammed channels and adjust your an-
tenna according to the “Antenna Adjustment and Signal
Check” section on page 14.
LNB Offset voltage
If the cable down from the antenna is very long, the voltage at
the LNB could be too low to change the polarization. You can in-
crease the voltage to the LNB by 0,5 V.
Please follow the procedure de-
scribed on page 14.
FIRST TIME INSTALLATION
OK
OK
OK

GB 17
FIRST TIME INSTALLATION
Multisatellite/DiSEqC switch configuration
Select this alternative if your antenna system has more than one
LNB and when you not use any of the alternatives Astra/Hotbird
or Thor/Sirius from the menu “Antenna/satellite selection”on
page 13.
You can connect up to 4 LNBs. The selection of the different LNBs
must be controlled by an external switch. Refer to page 15, “Con-
nection of a DiSEqC switch.”
Switch type and port
Here you select the input for each LNB that will be connected.
In this specific example, the DiSEqC 1 input will be selected first.
LNB type
Select “Universal”or the local oscillator (L. O.) frequency valid
for the connected LNB.
LNB Offset voltage
If the cable down from any of the LNB’s is very long, it might be
necessary to increase the voltage to these LNB’s by 0,5 V.
In most cases nothing has to be altered here. Leave the default
value “0 V”as it is. If the switch does not change between hori-
zontal and vertical polarization, the voltage to a LNB can be in-
creased later.
Increase the voltage:
a. only if a LNB does not change polarization
b. only to the specific LNB mentioned in a. above
Satellite
In this example, select Astra 2A because its LNB is connected
to the DiSEqC 1 input on the switch.
Predefined channel
Select one of the predefined channels and adjust the antenna as
described on page 14, “Antenna adjustment and signal check”.
Before you can continue, a TV picture from the predefined chan-
nel must be visible in the background.
When you do have a picture and press OK to continue, you re-
ceive a confirmation on the TV screen that the configuration of
the DiSEqC 1 input is ready. You will also be asked if you want to
configure another DiSEqC input. (Continue on the next page.)
For each LNB you connect to the DiSEqC switch, the fol-
lowing configuration has to be performed.
As an example the following part will describe how the LNB in-
tended for Astra 2A will be configured to the DiSEqC input 1 (A)
on the switch and the LNB intended for Eutelsat W2 to DiSEqC
input 2 (B).

GB 18
LNB type
•Select Universal, one of the fixed frequencies or enter the LNB
frequency with the numeric buttons on the remote control.
Type of motor
•Select SATSCAN if it is a Nokia SatScan motor.
•Select DiSEqC in case the motor you use is controlled by
DiSEqC commands.
Antenna Motor
In case you have an antenna motor to control your satellite an-
tenna you have to make the following settings.
•From the “Antenna/Satellite Selection”menu select line 7 (re-
fer to page 13) and press OK.
•Select line 3, “Motor Antenna Configuration”and press OK.
LNB Offset Voltage
If the cable down from the antenna is very long, the voltage at
the LNB could be too low to change the polarization. You can in-
crease the voltage to the LNB by 0,5 Volt.
FIRST TIME INSTALLATION
In this case also the input for the Eutelsat W2 satellite shall be
configured, so press OK. This means that the same procedure
as for Astra 2A has to be repeted. But this time select DiSEqC 2
from “Switch type and port”and Eutelsat W2 as the satellite.
When the configuration of DiSEqC 2 is ready, press OK. A con-
firmation that also DiSEqC 2 is finished will show up.
As no more input is to be configured, now it is time to start
searching for channels from the Astra 2A and Eutelsat W2 satel-
lites.
The channel search procedure is started by pressing the BACK
button. Please refer to the “Channel search”part on page 22.

GB 19
FIRST TIME INSTALLATION
Adjust Motor for ASTRA
To continue the installation you now have to determine
the angle to ASTRA 1. The motor and the antenna must
be adjusted towards the ASTRA 1 satellites on 19,2°
East as this is the reference setting. All other prepro-
grammed satellite positions are oriented relative to
ASTRA 1.
You also have to mount the antenna at a proper place
outdoors.
How to do all this, please read the separate Fitting In-
structions for the SatScan positioner.
(The figure to the right will appear when you select line 4 from
the menu above and press OK.)
On condition that the outdoor installations are finished, the an-
tenna is properly adjusted towards ASTRA and the Signal
Strength (AGC) bar is as strong as possible:
•Select one of the predefined ASTRA channel alternatives
•Press OK....
....and the Signal Strength bar will change to indicate the Signal
Quality (SNR) bar instead (Red/Yellow/Green) *). This indication
will show the signal quality from the predefined TV channel. Se-
lect the predefined channel that will give the best bar indication.
Within a few seconds you will also get picture from the channel
in the background.
•If necessary, select line 1 and fine tune the motor with the
buttons on the remote control.
•Press OK and you will return to....
*)If no indication is shown the antenna is probably not adjusted
towards ASTRA 1. Please refer to page 14.
....the Motor Antenna Configuration menu again.
As you now have picture from ASTRA, it is time to perform a
Channel Search procedure.
•Select one of the lines 1-3.
•Press OK......

GB 20
FIRST TIME INSTALLATION
....and you will get the Channel Search menu.
The most common is to start from the “Automatic Search”line.
(You can always make a Manual or Advanced Search later on.)
•Select ASTRA on the Automatic Search line
•Press OK......
.......and you get the Antenna Adjustment menu.
•If necessary, adjust the motor until the Signal Strength (AGC)
is optimal. Please note, that this will only affect the present
satellite position.
•Select one of the Predefined Channels and press OK.....
.....and you get a menu from where you can check the Signal
Quality (SNR) from the predefined channels. You must wait until
the picture appears that sometimes may take up to 10-15 sec-
onds.
•If necessary, adjust the motor until the Signal Quality (SNR) is
optimal. Please note, that this will only affect the present sat-
ellite position.
•Press OK to.....
.....start the main search procedure for (in this case) the ASTRA
channels. The search procedure will take a while. Please refer to
page 22.