Nokia Mediamaster 9602 S User manual

GB 1
Owner’s Manual
Mediamaster
9602 S
9610 S

GB 2

GB 3
Mediamaster 9602 S, 9610 S
For your safety
•KEEP A CLEAR SPACE
AROUND THE RECEIVER TO
ALLOW FOR SUFFICIENT
VENTILATION!
•NEVER COVER the receiver
or place it on a unit that
emits heat!
• Do not allow the receiver to be
exposed to hot, cold or humid
conditions.
• Use a soft cloth and a mild so-
lution of washing-up liquid to
clean the casing.
• Do not connect or modify ca-
bles when the receiver is
plugged in.
• Do not remove the cover.
• Pleasenotethattheonlywayto
isolate the receiver completely
from the 230 V mains supply is
to unplug the mains lead!
• Nokia is proud to offer a high
quality product. To keep this
level of quality, service should
be carried out only at a Nokia
authorised service centre.
We reserve the right to change specifications!
Please be aware that new software can change
the functionality of the Mediamaster.
DiSEqC™ is a trademark of EUTELSAT
The EMC Directive 89/336/EEC is applied to this product.
The sky is the limit with your Mediamaster. It‘s easy to use,
alwaysatyourcommandand adaptable for future advances.
To begin with, you will find it necessary to read these in-
structions but you will soon find yourself competent with-
out them.
Contents
For your safety 3
lnstallation of the Mediamaster 4
Overview of connections 5
Front panel 5
Connecting to different units 6
CA module and Smart Card 8
Switching on for the first time 8
Remote control 9
Before you go on... 10
Menu Information 10
Buttons 10
About Smart Card and the CA Module 11
PIN Code 11
Basic Settings 12
The Welcome Menu 12
Viewing TV 16
Select Channel 16
Programme information The”i” button 16
The Radio button 17
Sound level 17
Video Recorder 18
Analogue Receiver 18
Subtitling and Teletext. The TEXT button 18
Settings from the Main Menu 19
Radio Guide, TV Guide 19
CD 20
Parental Control 20
Common interface 21
Installation Submenus 22
Antenna Configuration 22
Channel Search 23
Language Settings 24
System Settings 24
Telephone Modem Settings 25
Receiver upgrade 25
Symbol on the Mediamaster display 25
Future Services 26
Glossary of terms 27
Technical Specifications 28

GB 4
SCART cable
Installing the satellite dish
• Your satellite dish should be installed with a cable for you to
connect to the Mediamaster. If you do not have this cable you
will need to buy one from a dealer (tell the dealer you need a
coaxial cable and F-connectors).
• Connectthe cable from thesatellite dish to thesocket marked
”LNB”on the back of the Mediamaster.
8 mm
15 mm
3 mm
F-connector
Owner’s manual
The box for your Mediamaster should contain the following
items:
• the Mediamaster
• a remote control handset with batteries
• a fully featured SCART cable which can be used to connect
your Mediamaster to the TV or video recorder
• an Owner’s Manual for the Mediamaster
Installation of the Mediamaster
About the SCART sockets
• On the back side the Mediamaster is equipped with 3 SCART
sockets(Seefigure).When you connect external sets to any
of these sockets, always use fully featured SCART Cables.
There are “slimmed” (=cheap) SCART cables on the market,
but it is not so sure that e. g. your Videorecorder will work OK
with some of those cables.
Connecting the Mediamaster to the satellite dish
If you need to fit the F-connectors onto the cable
• Prepare each end of the cable as shown in the diagram. You
will need to fold back the outer braid (as shown).
• Slide the F-connector onto the cable, then turn it clockwise
until it grips the braid.
• Ensurethat 3 mm of the core isprotruding from the end of the
connector.
SCART socket
56
123
4
789
0
EXIT
MENU
GUIDE
OK
TV
TEXT

GB 5
AUDIO L R
Stereo outputs
for connection
to a HiFi system
TV SCART
for the audio /
video input of
the TV set
SATELLITE
SCART for an
analogue
receiver
VCR SCART
for a video
recorder
*LNB cables also feed the LNB with a sup-
ply voltage of 13/18 V (V/H polarisation) and
a 22 kHz signal for LNB switch.
0/12 VOLT
for an external
LNB switch
Mains lead
230 V AC +/-
15%,50 Hz
LNB *
Satellite dish
input(F-
connector)
Overview of connections
RS232
for a printer,
PC or a high
speed modem
TELEPHONE LINE
for modem
connection to the
telephone jack
CTRL VIDEO
for an IR-diode
cable connec-
tion to a video
recorder
SCSI
(9610 S)
for a CD-ROM
player or other
high-speed data
equipment
Slot
for the CA module
with Smart Card to turn the
Mediamaster
on/off (standby)
to step up and
down programme
number
Display
shows programme
information.
When Mediamaster start
up, it displays software
version and boot-loader
number
Front panel
Welcome

GB 6
• Do not remove the cable from the TV to the TV aerial.
• Connect one end of the SCART cable to the TV SCART socket
on the back of the Mediamaster and the other end to the
SCART input socket on your TV.
• Go straight to “Preparing the remote control” on page 8.
Connecting to the TV set
Connecting to a TV and a Video Recorder
Refer to your video recorder manual for full instructions.
• Connect one SCART cable between the TV and the TV SCART
socket on the Mediamaster.
• Connect the other SCART cable between the video
recorder and the VCR SCART socket on the
Mediamaster.
• Connect a RF cable from the RF output on the
video recorder to the TV aerial input on the TV.
• Connect the ordinary TV aerial directly to the RF input socket
on the video recorder.
Go straight to ‘Preparing the remote control’ on page 8.

GB 7
Analogue receiver
Mediamaster
NOKIA Smart
priority switch
A
B
Connecting to a Hi Fi System
• Connect a RCA/Cinch stereo cable from the AUDIO L R sock-
ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA
input sockets on your Hi Fi system.
Connecting to an analogue receiver and a video recorder
• Connect one SCART cable between the TV and the TV SCART
socket on the Mediamaster.
• Connect one SCART cable between the TV SCART socket on
the analogue satellite receiver and the SAT SCART socket on
the Mediamaster.
• ConnectoneSCARTcablebetweenthevideorecorderandthe
VCR SCART socket on the Mediamaster.
• Connect a RF cable from the RF output on the
video recorder to the TV aerial input on the TV.
• Connect the ordinary TV aerial directly to the RF
input socket on the video recorder (TV if no VCR).
In order to switch the signal from the dish between the ana-
logue and digital receivers, you need a Nokia Smart priority
switch (see diagram).
• ConnectacoaxialcablebetweenoutputAontheNOKIASmart
priorityswitch(accessory) to the LNB socket on the analogue
receiver.
• ConnectacoaxialcablebetweenoutputB on the NOKIA Smart
priority switch (accessory) to the LNB socket on the Media-
master.
Note: With this connection the analogue receiver has priority
over the Mediamaster and can receive satellite signals irre-
spectiveof all otheractive units. The Mediamastercan receive
signalsonlyif the analogue receiverisin standby or unplugged.
With Video Recorder
A
B
Analogue receiver
Mediamaster
Without Video Recorder

GB 8
You can now plug in the mains plug of the Mediamaster to the
wall socket.
• Switch on your TV set.
• Switch on the Mediamaster by pressing the TV button on the
remote control.
• When you see the welcome message, press the OK button
on the remote control.
Preparing the remote control handset
• Remove the cover on thebattery compartment on the bottom
of the remote control handset.
• Insert the 2 x AAA (1,5 V) batteries, as shown in the diagram,
taking care to observe the +and -markings indicated inside.
• Replace the cover.
CA module and Smart Card
If you want to watch the TV programmes from your Service
Provider you must use the CA module (Conditional Access)
with the Smart Card. The CA module give you e.g. access to
special menus from your Service Provider.
If no CA module is used you can only watch ”free” TV pro-
grammes.
More about this later.
Note: The mains plug must not be plugged in before insert-
ing the CA module.
• Insert your card fully into the slot in the front panel of the CA
module, so that the microchip (the yellow metal spot) faces
upwards and inwards.
• Insertthe CA module with SmartCardfully into the slot behind
the lid in the front panel of the Mediamaster so that the ar-
row on the module faces upwards and inwards.
Switching on for the first time

GB 9
To turn the Mediamaster on/off (standby).
Press once to switch to audio language/audio track
Press twice to switch to radio mode.
TV To leave a menu and go back to watch a TV pro-
gramme. To switch from Radio Mode to TV Mode.
To toggle between terrestrial TV, VCR, analogue and
the digital satellite signal.
0 - 9 To select channel number and other numerical
commands.
GUIDE To obtain a list of present and comming programs.
This information is only shown if your Service Pro-
vider transmits programme information.
MENU To display the ”Main menu” screen.
EXIT To go back one level in the menus.
To return to the Main Menu from a Submenu.
To give short and extended information (if transmit-
ted) about the current/next programme.
LEFT/RIGHT To move in left/right direction within the menus.
BUTTONS
UP/DOWN To move in an up/down direction in the menus.
BUTTONS To select TV and radio channels.
DOUBLE To step page up or down in the menus (in blocks of 10).
ARROWS
OK To confirm choices, etc.
+ - To increase or decrease the volume level of the
Mediamaster.TheMediamaster’smaximum level is
controlled by the TV:s present volume setting. The
volume adjustment also alters the volume level to
your video recorder.
To turn the sound on /off (mute).
TEXT To select teletext information.
Press once to change teletext subtitle
Press twice to enter teletext (if available)
Please note that the above mentioned descriptions may be differ-
ent if you are “Home Shopping” or connected to other on-line
services.
To replace the batteries in the remote control, see the instruction
on page 8.
Double arrow
UP
DOWN
RIGHT
Double arrow
LEFT
Remote control
This section describes how to operate the Mediamaster using the buttons on the remote control.
You can also change programmes by pressing buttons on the Mediamaster‘s front panel.

GB 10
OK
Buttons
With the up/down buttons on the remote control you can move
to different lines in a menu.
With the right/left buttons you can select between different al-
ternatives on a line.
When you have reached the required subject line, press the OK
button to confirm your choice.
There are also double arrows pointing upwards/downwards.
These are shown when a menu consists of more than one page.
Use the buttons to change menu page.
These buttons are also used when you wish to move faster
(10 at the time) in the lists of TV and Radio channels.
Menu Information
Before you do anything else, please read the following explana-
tion of how to operate the menus which will appear on the TV
screen.
A menu is a field of text shown on the TV screen. These menus
contain different kinds of information and give the possibility to
select between alternatives.
In the bottom part of the screen you will normally also have a
short explanation of your options.
A menu may contain several lines. Selectable lines are generally
highlighted. Not highlighted lines are not selectable.
Before you go on...
please read this concerning menus and buttons
LEFT
Double arrow
UP
DOWN
RIGHT
Double arrow

GB 11
About Smart Card and the CA Module
To be able to receive pay-TV channels you will need an CA Mo-
dule and a Smart Card from the Service Provider of your choice.
The Service Provider is the distributor of the programmes.
If you are subscribing to services from more than one Service
Provider, you might have to change between two Smart Cards,
or even between two CA Modules.
Please note, that a smart card is connected to a single Service
Provider and due to this, a specific range of channels.
It is possible to view "free" channels without the CA Module.
After inserting the card, leave it in the slot permanently. Do not
remove it again, unless your Service Provider asks you to do so.
This is important, because if your Service Provider wants to
download new information to the Mediamaster, the card has to
be in the slot.
PIN Code
Thecardisloadedwitha4-numberedcode,also called a PIN code
(Personal Identification Number). Normally the PIN code is 1234.
The code is essential for the future extra services offered by the
Service Provider.
Information for these services will be described further on in this
Manual.

GB 12
Antenna configuration
In order to configure your equipment (satellite dish and LNB) you
will need to use the following menus.
The LNB is the unit that is mounted on the satellite dish. For
thefollowingsetupprocedureyouhavetoknowthe frequency
valid for your LNB(s).
If you have a single satellite dish equipped with 1 LNB:
The line with the alternative “One antenna/LNB for THOR” is
highlighted.Asthisisthemostcommonalternativeandyouknow
you are going to watch transmissions from THOR, all you have
to do is to press the OK button.
However, if you have another combination, select an alternative
from any of the other lines.
Please note that THOR, ASTRA and HOTBIRD all have a prepro-
grammed channel, which is a great help when you are adjusting
the dish towards one of those satellites.
Pressing OK from any of the lines with named satellites will re-
sult in the menu to the right coming up on the screen.
The first line will show the name of the satellite.
On line “LNB Frequency”, select the frequency alternative that
is valid for your LNB.
The alternatives are: “Universal” (which is the most common),
“DiSEqC”, “9.750”, “10.000”, “10.050”, “10.750”, “11.200”,
“11.475”, “5.150” and also a possibility to enter another alter-
native with the number buttons on the remote control.
Proceed to headline ”Dish adjustment” on the next page.
Language and Country selection
Selectthe desired language. This will define thelanguage shown
in the menus. It will also select this language as the main lan-
guage in case more than one is transmitted for talk and subtitling
in movies.
Ifyourreceiveris equipped with a telephone modem, you will also
get a menu from where you must select the Country where the
receiver is installed.
The Welcome Menu
To install the Mediamaster properly you have to perform a few
settings. You will always be guided by the information in the
menus.
Whenyouhavefinishedthe setup procedure you can start watch-
ing TV channels and listen to Radio channels.
Push the button on the remote control to start the Media-
master from stand-by position.
The “Welcome Menu” will now appear on the TV screen.
Press the OK button to proceed.
Basic Settings

GB 13
Dish adjustment
The Mediamaster is preprogrammed for receiving signals from
THOR (ASTRA and HOTBIRD), and if the dish is already correctly
adjusted you should now see a programme from that satellite in
the background.
If not, or if the picture/sound is not satisfying, you have to adjust
the dish to improve the reception quality.
Check the signal strength meter at the lower part in this menu.
Adjust the dish mechanically to get the best possible signal
strength.
When you have made the necessary settings for your combina-
tionandhave picture and sound, you maynowproceed to “Chan-
nel Search” (= download channels from the satellite) by press-
ing the OK button.
If you have a single satellite dish equipped with 2 LNBs;
or two dishes with one LNB on each:
The Mediamaster is preprogrammed for the LNB combination
ASTRA/HOTBIRD. It is also preprogrammed for the connection
of an external switch. This external switch should be either;
1 A so called DiSEqCTM swich (Level 1 or 2 type), or;
2 A 0/12 V switch.
Both of these automatically switch between two LNBs, but
there is one big difference between them.
The DiSEqC switch can be located close to the LNBs, which
means you have only one cable down to the Mediamaster.
The 0/12 V switch must be located close to the Mediamaster,
which means you will have two cables, one from each LNB,
all the way down to the Mediamaster.
Ifyouhavemadethe selection ASTRA/HOTBIRD from this menu,
you must connect one of those switches.
In the menu that appears when you have select the combination
ASTRA/HOTBIRD, you have to make two settings:
1 Select ASTRA on the first line and your LNB type for this
satellite on the second.
2 Select HOTBIRD on the first line and your LNB type for this
satellite on the second.
When you perform the dish adjustment described below, don’t
forget to alter between ASTRA and HOTBIRD in this menu.
If your dish/LNB configuration differs from the alterna-
tives above (= you have to select “One antenna/LNB for
any other satellite” or “Multiantenna/LNBs for multiple
Satellite positions”), please proceed to “Antenna Configu-
ration Set-Up” further on in this manual.
0/12 V
switch
DiSEqC
switch

GB 14
Channel Search
From the Channel Search menu the Mediamaster will automati-
cally search for TV and Radio channels digitally transmitted from
the satellite which your dish is aimed at.
The search will be performed in a predetermined way, and all
channels found will be listed in two columns on the screen.
TV channels will be listed in one column, Radio channels in the
other.
Please note, that the search procedure may take a few minutes.
When the search procedure is finished the indication
“Ready. To watch TV press OK” will appear in the bottom part
of the menu.
Whenyou press OK a newmenu superimposed upon theTV pic-
tureappears, where you havethe opportunity to adjustthe clock.
This is done with the UP/DOWN buttons, ±1/2 an hour at the
time.Afterthat,theMediamasterwillautomaticallykeepthe right
time.
Now you are ready to watch TV. Please proceed to “Viewing TV”
in this Manual.
Antenna Configuration Set-Up
The following description is an “Advanced procedure” and
is only necessary if you have special equipment connected.
If you have another antenna combination you can configure it
from this menu, which appears when you make a selection from
the “Antenna Configuration” menu, line “One antenna, LNB for
any other satellite” or line “Multiantenna/LNB for multiple satel-
lite positions”.
Antenna alternative: Select an Antenna alternative from
1 to 8. Please note, that the parameters in the menu are prepro-
grammed, but you can change any of them to suit your combi-
nation.
Name for this satellite: From here youcan select a name forthe
configuration.
LNB Frequency:Selectionis possible for different kinds of LNBs.
Select the frequency for the LNB that is valid for your combina-
tion. You may also enter a value with the number buttons on the
remote control.
0/12 Volt antenna switch: Control of an external LNB switch,
i. e. switching between two different satellite dishes.

GB 15
DiSEqC input selection: There are in principle two kinds of ex-
ternal DiSEqC switches on the market at present. One for con-
nection of two LNBs. The other one for connection of up to
4 LNBs.
If you connect a two input switch that it is of a so called “Tone
Burst” type, select Mini A for the LNB connected to input A on
the switch; select Mini B for the LNB connected to input B.
If you have the other switch, defined as “DiSEqC, Level 1 or 2”
on the market, select DiSEqC 1, 2, 3 and 4 for each LNB con-
nected to respectively input on this switch.
An OK from any of the alternatives in this menu will take you to
the “Channel Search Set-Up” Menu below.
The “Channel Search Set-Up” Menu
The information to enter in this menu you will find in magazines
concerning satellite TV reception, or from your Service Provider.
Antenna configuration name: Step between the names you
have entered in the “Antenna Configuration Set-Up” menu.
(Practically, this means that you select between the connected
LNBs).
Transponder Frequency: With the number buttons on the re-
mote control, enter the Transponder Frequency.
Polarization: Select polarization; “Horizontal or Vertical”
Symbol rate: Enter with the number buttons.
FEC: Enter type of Forward Error Correction (FEC).
Network search: Select “Yes” to search all transponders used
by a special Programme Distributor.
Yes” is the default setting.
Select “No” to search from only one transponder.
By pressing the OK button you can now enter the menu from
where the Mediamaster starts to download channels from the
satellite(s).
IMPORTANT! If more than one LNB is connected you have to
perform the downloading procedure once for every LNB!

GB 16
Start/stop watching TV
To start the Mediamaster from standby mode, press the but-
ton,TV button or one of the number buttons on the remote con-
trol.
It is also possible to start by pressing the button behind the
lid on the front of the Mediamaster.
Putthe Mediamaster into standbyby pressing the samebuttons.
The clock will be shown on the display during standby mode.
Select Channel
Change channel with the number buttons or with the up/down
buttons.
Programme Information. The “ “ Button
The following will describe the basic functions of your Media-
master while watching TV.
Sometimes the information may not be displayed as illustrated.
Manyof the functions described herearedependent on the Serv-
ice Provider and can only be used if they are supported by the
Provider.
Every time you change channel you will receive information dur-
ing 4-5 seconds, of the current programme. This information in-
cludes: Channel number, name, title and time.
Press while watching a channel. If your Service Provider trans-
mits programme information you will see:
Correct time;
A small amount of information for the current and next pro-
gramme. (Alternate between “Now” and “Next” with the left/
right buttons);
Name and number of the channel;
Finally the start and stop time for the programme.
From here you can also get information about other channels.
Select with the up/down buttons. If you stop on another chan-
nel number and press OK, you will exit the menu and return to
TV mode, but now on the new channel.
Ifyouhave select “Next” on a programmelineand press OK, you
will set a “Reminder”. This means that, while watching TV, you
will be reminded when the “Reminder marked” programme
starts.
If you press the button once more, you will get extended infor-
mation (if transmitted) for the current or next programme.
To exit the menu, press the TV or button.
Viewing TV

GB 17
The Radio button
Pressing the button once gives you a menu where you can
change the spoken language in the present TV programme.
(This provides that more than one language is transmitted).
Some TV channels also transmits radio channels selectable from
this menu. These channels are often named “Track 1, 2, 3...”).
Sound level
Increase or decrease the sound level by pressing the PLUS and
MINUS buttons.
A control bar will be displayed on the screen during level adjust-
ment. (The max. level for sound is the current volume on the TV
set).
Please note, that the volume adjustments also change the
volume level to your VCR.
It is possible to turn the sound on and off with the button.
Sound off is indicated with the same symbol on the screen.
List of TV and Radio channels
While watching TV or listening to Radio in Radio Mode, you get
a programme list on the screen by pressing the OK button.
Change channel by stepping with the UP/DOWN buttons to an-
other channel and then press the OK button.
Please, also see the TV and Radio Guide Instructions on p. 19.
Pressing the button twice will lead to the specific Radio Chan-
nel mode. The display on your Mediamaster and the TV screen
will show the name of the radio channel you are listening to.
While in radio mode, you can press the button to get extended
information (if transmitted) about the radio programme.
Return to TV mode by pressing the TV button or again.

GB 18
Subtitling and Teletext. The TEXT button
Pressing the TEXT button once while watching TV will give a
menu on the screen where it is possible to change a subtitled
language. This is only possible if more than one subtitling lan-
guage is transmitted.
Exit the menu by pressing the TV button.
Video recorder
If a Video Cassette Recorder (VCR) is connected you can watch/
record video tapes. When you press the Start button on the VCR
the playback will start and interrupt the TV programme from the
Mediamaster.
To watch TV programmes again, press the TV button or stop the
VCR.
Please note, that during the recording of a programme, every-
thing shownonthescreenwill be registered! For example: If you
call up a Menu from the Mediamaster on the screen, the menu
will be recorded.
Analogue Receiver
If you have an Analogue Receiver connected and turn it ON, the
programmes from it will be shown. Turn it OFF, and the pro-
gramme from the Mediamaster will be shown.
Youcanalsotogglebetweenprogrammesfrom the Mediamaster,
analogue receiver and terrestrial (=”normal”) TV with the TV
button on the remote control.
Pressing the TEXT button twice will give the teletext menu,
(if teletext is transmitted). Select pages with the UP/DOWN or
the number buttons remote control.
You canalsoquickly step to the different page alternativesshown
in any page by pressing the LEFT/RIGHT buttons. Press OK on
a selected number, and the page will show up.

GB 19
How to show the Main Menu
Press the MENU button and you will get the Main Menu on the
TV screen. Press the TV button to leave the menu.
Submenus from the Main Menu
If you select one of the highlighted titles and press the OK but-
ton, a submenu will be shown on the TV screen.
From a submenu you can adjust settings to your own require-
ments.
Radio Guide
This Guide will give you an overview of programme information
fromthe Radio channels. Step to different channelnumbers with
the UP/DOWN buttons.
If you stop on a line and press OK, you will exit the menu and
enter the Radio channel marked on the line.
Select information about the next programme with the RIGHT
button.
Use the button to get extended information.
Common to both the TV- and Radio Guide are that the pro-
gramme information is only shown if your Service Provider
transmit it.
TV Guide
Depending on the software version in the Mediamaster
you might have a 7-day TV Guide. If not, the TV Guide will have
the same functionality as the Radio Guide. However, all receiv-
ers will get a 7 day TV Guide with the future software versions.
If you have a 7 day TV Guide, it is possible to see the comming
programmes for the next 7 days.
Changedate(in top of the menu) withthedouble arrow buttons.
Use the Up/Down/Left/Right buttons to move between and
within the menus.
Pressing the button once ore twice while in one of the fields
will give information respectively extended information (if trans-
mitted).
Settings from the Main Menu

GB 20
TV Channels
TV Channels will show a list with the names of the different TV
channels.
To move faster within the list, usetheDOUBLE ARROW buttons.
Press OK to enter a marked channel.
Radio Channels
Radio Channels will show a list with the names of the different
Radio channels.
To move faster within the list, usetheDOUBLE ARROW buttons.
Press OK to enter a marked channel.
Parental Control
With the Parental Control functions you have the possibility to
controltheaccesstotheMediamasterandalsoto individual chan-
nels.
By entering the PIN code 1234 you reach the menu where you
can lock different functions in the Mediamaster.
Message
If the Service Provider has any special messages to the viewers
they can be presented here.
CD (9610 S)
From the CD menu you can control an external CD player con-
nected to the SCASI socket.
To use the present and future CD-ROM applications, the player
must have the following features:
a) SCSI-2 connection
b) support of the following standards: CD-XA / CD-ROM /
Video-CD/ Photo CD