Nokia Mediamaster 9828 User manual

Owner’s Manual

GB 3
MEDIAMASTER 9828 T
Nokia and Nokia Connecting People are registered trademarks of Nokia Corporation. Other product
and company names mentioned herein are trademarks or trade names of their owners.
Nokia operates a policy of continuous development. Therefore we reserve the right to make changes
and improvements to any of the products described in this manual without any prior notice.
Copyright © 2001. Nokia Corporation.
All rights reserved.
Contents
General information 4
For your safety 4
Remote control 5
Front and rear panel 6
About smartcard and CA module 7
General 7
Inserting the CA module and the smartcard 7
Connection 8
Preparing the Remote Control 8
About the digital transmission 9
Connecting to the TV aerial 9
Connecting the Mediamaster 10
Connecting the Mediamaster to the TV 10
Connecting a TV and VCR 10
Connecting an Satellite Receiver and a VCR 11
Connecting a HiFi system 11
Switching on for the First Time with
SCART Connections 12
Procedure when RF Connections are Used 12
First time installation 13
General Information 13
The Welcome Menu 13
Language 13
RF modulator type 14
Channel Search 14
Channel Search Progress 15
Time adjustment 15
Finishing the first time installation 15
Viewing mode 16
General Information 16
Programme Information 16
Application Download (“Open TV”) 16
Information. The “i” button 17
Guide 17
List of Channels 18
Options. The green button 18
TV Release. The 0 button 19
Video Recording 19
Teletext. The TEXT button 19
EXIT TV 19
Main menu 20
General Information 20
TV and Radio Channels 20
Edit Channels 20
Guide 24
System Configuration 24
Channel Search 24
TV Settings 25
Time adjustment 25
Receiver Upgrade 26
Reinstall 26
User Preferences 26
Language Preferences 26
Parental Control 27
Appearance Preferences 27
System Information 28
Conditional Access 28
Glossary of terms 29
Problem solving 30
Front panel display 31
Technical specifications 32

GB 4
GENERAL OPERATION OF THE MEDIAMASTER
Throughout this manual you will notice that the everyday op-
eration of your Mediamaster is based on a series of user friendly
on-screen displays and menus. These menus will help you get the
most from your Mediamaster, guiding you through installation,
channel selection, viewing and many other functions.
All functions can be carried out using the buttons on the re-
mote control, and some of the functions can also be carried out
using the buttons on the front panel.
If at any time when using the menus (except Installation and
Reinstall) you want to return to the normal TV mode, press the
EXIT button.
Should you experience any difficulties with the operation of
your Mediamaster, please consult the relevant section of this
manual, including the Problem Solving, or alternatively call your
dealer or a customer service adviser.
• Use a soft cloth and a mild solution of washing-
up liquid to clean the casing.
• Do not connect or modify cables when the
Mediamaster is plugged in.
• Do not remove the cover.
• Service should be carried out only at a Nokia
Authorised Service Centre.
• Please note that the only way to isolate the
Mediamaster completely from the mains supply
is to unplug the mains lead!
FOR YOUR SAFETY
• For sufficient ventilation, there must be at least
10 cm free air space above, behind and on each
side of the Mediamaster.
• Do not cover the Mediamaster's ventilation
openings with items such as newspapers, table-
cloths, curtains or similar.
• Do not place the Mediamaster on top of a unit
that emits heat.
• Do not expose the Mediamaster to dripping or
splashing liquids.
• Do not place any objects filled with liquids, such
as vases, on the Mediamaster.
• Do not place naked flame sources, such as
lighted candles, on the Mediamaster.

GB 5
Switch the Mediamaster in and out of standby mode.
EXIT TV To return to the viewing mode from a menu without stor-
ing settings (in menu mode.)
Switch between TV or Radio mode (in viewing mode.)
Turn the sound off/on (mute.)
- + Adjust the volume. The Mediamaster’s maximum level is
controlled by the TV’s present volume setting.
0 - 9 Change channel and to select individual menu options.
Note: If 0 is entered as the first digit, the TV Release func-
tionality is activated (see below.)
0 TV Release. Switch between digital TV, analogue TV and
analogue satellite TV and VCR, when your systems are con-
nected by SCART leads.
Info. To display short and extended information (if transmit-
ted) about current and next programmes.
BACK Go back one level in the menus.
TEXT Select teletext information.
Press to enter teletext (if available).
MENU To display or exit from the ”Main Menu” screen.
GUIDE To obtain a list of present and following programmes for the
available channels. This information is only shown if your
Service Provider transmits programme information (EPG
information.)
P+ P- Change channels up and down.
Change page in a menu/list/text if more than one page is
available. To browse through teletext history.
Move up/down in the menus and to change channels.
Change settings in menus.
OK Confirm choices and selection of a highlighted item.
Display the TV channel list.
(Red) To download an “Open TV” application
OPTION (Green) Select options in viewing mode.
(Blue) Toggle between present and previous TV/Radio
channels.
FREEZE (Yellow) Select the freeze function.
Press once to freeze the screen picture.
Press any other key to return to normal mode again.
This section describes how to operate the Mediamaster using the buttons on the remote control.
Some of the functions can also be carried out using the buttons on the front panel.
REMOTE CONTROL

GB 6
Rear Panel
AUDIO L R
phono connectors
Stereo outputs for
connection to a HiFi
system
TV SCART
for connection
to the TV
AUX SCART
for connection to a
VCR, or an analogue
satellite receiver
DIGITAL AUDIO
phono connector
S/PDIF output for con-
nection to a HiFi sys-
tem
Mains lead
95 - 250 V AC
50-60 Hz
SERIAL PORT
to read and load
data information
TV AERIAL
for a terrestrial (con-
ventional) TV aerial or
an additional small
indoor aerial
TV/VCR
for an RF-cable to
the aerial input of
the TV or VCR
Front Panel
Slot
for a CA module with a
Smartcard
for several functions, e.g
selecting channels, high-
lighting an option within a
menu or scrolling through
channels
Display
shows channel information, er-
ror messages, remote control
commands and time in stand by
mode
Button
for the CA module
release
to put the
Mediamaster in and
out of standby
FRONT AND REAR PANEL

GB 7
Inserting the CA module and the smartcard
Insert the CA module and the smartcard according to the instruc-
tions provided with the module.
ABOUT THE SMARTCARD AND CA MODULE
General
To be able to receive terrestrial scrambled digital channels you will
need a CA module and a Smartcard from a Service Provider.
There are a few different CA modules on the European market.
Each one of the CA modules support a certain kind of encryption
system. Examples of such a system are Viaccess, Conax, Irdeto,
Nagravision and Mediaguard. Depending on in which country you
use the Mediamaster, your local salesman will provide you with
the right type of CA module.
Please note that a Smartcard may only be valid for a single Serv-
ice Provider and due to this, a specific range of channels.
The Smartcard and the CA module may cause special menus not
described in this manual. Follow the instructions from the Serv-
ice Provider.
Note: The CA modules and Smartcards are only distributed by
Service Providers and special distributors, not by Nokia.
After ins<ard, leave it in the slot permanently. Do not remove it
again, unless you will be asked to do so. This is important, be-
cause if, for example, your Service Provider wants to download
new information to the Smartcard, the card has to be in the slot.
CA module
Smartcard
Smartcard
CA module

GB 8
The box for your Mediamaster should contain the following items:
• the Mediamaster
• remote control with 2 AAA batteries
• SCART lead (fully featured 1,0 metre)
• aerial/RF lead (double screened 1,5 metres)
• Owner’s Manual
• Software License agreement
• mains lead
CONNECTION OF THE MEDIAMASTER
About the SCART sockets
• The rear panel of the Mediamaster is equipped with 2 SCART
sockets (see diagram). When you connect other products
to any of these sockets, always use fully featured SCART
leads (as supplied). There are “less well specified” SCART
leads on the market and picture quality could be reduced if you
use them.
SCART socket
SCART lead
Owner’s manual License
agrement
RF lead
Preparing the Remote Control
• Remove the cover on the battery compartment at the bottom
of the remote control.
• Insert the 2 AAA (1,5 V) batteries, as shown in the diagram,
taking care to observe the +and -markings indicated inside.
• Replace the cover.
Mains lead
Remote
control

GB 9
Connecting to the TV aerial
You can connect the Mediamaster to the following type of aerials:
1. Standard outdoor aerial
Where possible, use an outdoor roof aerial intended for receiv-
ing UHF channels between 21 and 69.
Please note the following:
• In some block of flats, the roof-mounted aerial system includes
a filter and channel selector. If so, the aerial will probably not
work with the Mediamaster. Please consult the landlord.
• Many older roof-mounted aerials may only receive a limited
number of channels. As a result, digital channels transmitted
on higher frequencies are difficult or even impossible to re-
ceive. The problem can be solved by replacing the roof aerial.
• Some outdoor aerials are directed towards an analogue trans-
mitter. The aerial must be directed towards a digital TV trans-
mitter.
• It is not always advisable to position the aerial as high as pos-
sible. If problems arise, experiment with different aerial
heights.
INSTALLATION OF THE MEDIAMASTER
About the digital transmission
Digital Radio and TV signals can be blocked by buildings, moun-
tains and the terrain. Depending on if the receiver is located in a
depression in the ground, behind a mountain or in a concrete
building, the quality of reception may vary considerably.
A digital signal can be “boosted” if reflections of it (from e. g. a
building) are added to the original signal.
Reflections can be used for reception by directing the aerial to-
wards a mountain or a high building, providing that they do not
block the transmitter.
As with most other transmissions, bad weather does affect the
reception quality negatively.
2. Indoor and window-mounted aerials
This type of aerial may be enough if the reception conditions are
very good. If an indoor aerial is used, please note the following:
• Use an aerial for UHF channels 21 - 69, such as a directional
aerial.
• Place the aerial by the window and directed towards the TV
transmitter, if possible.
• An aerial with an amplifier is recommended as it may provide
a stronger signal.
• The strength of the TV signal varies according to reflections
from e. g. buildings. The signal penetrates thick stone or con-
crete walls poorly. However, a wooden building is not a big bar-
rier to digital TV signals.

GB 10
• Connect a SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
• Connect a SCART lead between the VCR and the AUX SCART
socket on the Mediamaster.
• Connect a SCART lead between the VCR and the second
SCART socket on the TV.
• Connect an RF lead from the TV/VCR output on the Media-
master to the RF input socket on the VCR.
• Connect an RF lead from the RF output on the VCR to the TV
AERIAL input socket on the TV.
• Connect the TV aerial directly to the TV AERIAL input socket
on the Mediamaster.
Connecting the Mediamaster to the TV
• Connect a SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
• Connect an RF lead from the TV/VCR output on the Media-
master to the RF input socket on the TV.
• Connect the TV aerial to the TV AERIAL input socket on the
Mediamaster.
Connecting the Mediamaster
There are many different types of TV/VCR and other equipment
you can connect to the Mediamaster.
In this manual you will see some of the most common ways to
connect your equipment.
If you use RF leads you will have to tune your TV and VCR to the
Mediamaster output channel (see page 12).
If you have problems with your connections and need help, con-
tact your dealer or Service Provider.
Connecting a TV and VCR
Refer to your VCR’s manual for full instructions.
If your TV and VCR have two SCART-sockets
If your VCR only has one SCART-socket
• Follow connection details from above, but without the 3rd
SCART lead.
Your VCR will then need to be tuned to the Mediamaster.
RF
Video
SCART Aerial
RF
Aerial
SCART
RF
Video
RF SCART
INSTALLATION OF THE MEDIAMASTER
Media-
master
SCART
SCART
RFSCART
Media-
master

GB 11
Connecting an Satellite Receiver and a VCR
Connecting a HiFi system
• Connect an RCA/Cinch stereo cable from the AUDIO L R sock-
ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA
input sockets on your HiFi system.
• If available you can connect an RCA/Cinch single cable from
the DIGITAL AUDIO socket on the Mediamaster to your HiFi
or Dolby Pro Logic system.
Note: To avoid interference you must use a screened audio
cable.
• Connect a SCART lead between the main SCART socket on
the TV and the TV SCART socket on the Mediamaster.
• Connect a SCART lead between the TV SCART socket on the
satellite receiver and the AUX SCART socket on the
Mediamaster.
• Connect a SCART lead between the VCR and the 2:nd SCART
socket on the TV (if available).
• Connect an RF lead from the RF output on the VCR to the TV
aerial input on the TV.
• Connect an RF lead from the RF output on the satellite receiver
to the RF input socket on the VCR.
• Connect an RF lead from the TV/VCR output on the Media-
master to the RF input socket on the satellite receiver.
• Connect the TV aerial to the TV AERIAL input socket on the
Mediamaster.
• Connect the coaxial cable between the LNB and the LNB
socket on the satellite (analogue or digital) receiver.
Both the VCR and the analogue satellite receiver must be
tuned to different UHF channels than the Mediamaster when
using RF-connectors.
The analogue satellite receiver must be switched to OFF
(standby) when you want to watch digital terrestrial chan-
nels from the Mediamaster.
INSTALLATION OF THE MEDIAMASTER
Satellite receiver
RF
Aerial
RF
SCART
Antenna
Media-
master
VCR

GB 12
This procedure is necessary only if your Mediamaster is con-
nected to the TV with an RF lead and no SCART leads are
used.
To tune your TV to the RF signal you might also need your TV
manual in addition to this manual. The steps below explain what
to do if you have been unable to use SCART leads in your con-
nection.
•Plug in your Mediamaster.
Tuning your TV to the Mediamaster
•Select a channel number on the TV that is not currently used
for other TV channels.
•Follow the instructions in your TV manual to tune the TV chan-
nel selector to UHF channel 43 (this is the Mediamaster’s fac-
tory preset UHF channel). If you are already using this chan-
nel, select another non occupied UHF channel between 21to
69 on the TV.
•If you need to change UHF channel you do as follows:
First you change on the Mediamaster. Use the or buttons
on the front panel of the Mediamaster, or on the remote. You
will see the UHF channel number displayed on the front panel
of the Mediamaster. Then, tune the TV channel selector to the
same UHF channel.
•When you have correctly changed the UHF channel number
you will see the ”
Welcome ”menu on the TV screen.
If there is interference from other channels you will have to
change the chosen UHF channel.
•Follow the instructions in your TV manual to store this UHF chan-
nel as the channel used by your Mediamaster. You will have to
select it when you want to watch terrestrial digital TV channels.
•Once the welcome message is visible, press the OK button
on the Mediamasters remote control to start the installation
procedure.
If for some reason you have to change the RF channel later,
you can do this by using TV settings menu further on in this
manual. If you have a VCR connected it must be tuned to a dif-
ferent UHF channel (between 21 to 69) than the Mediamaster.
You may now proceed to “First Time Installation.”
Procedure when RF Connections are Used
INSTALLATION OF THE MEDIAMASTER
•Plug in your Mediamaster
•Now you will see the ”Welcome”menu on the screen.
•Press OK on the Mediamaster remote control to start the In-
stallation procedure.
You may now proceed to “First Time Installation.”
Switching on for the First Time with
SCART Connections

GB 13
Language
Select the desired menu language.
This will also be the main language for audio and subtitling.
General Information
Once you have correctly connected the Mediamaster, you also
have to perform a “First Time Installation.”
During this procedure, helpful information is displayed at the bot-
tom of the menus.
Please note!
The OK button always confirms a selection within these menus,
and pressing it will take you to the next step in the installation
process. However, and this is important, often more than one
value has to be entered in a menu. First, perform all necessary
settings on the different lines. Then, confirm them all simultane-
ously by pressing OK.
You can always go back to the previous menu by pressing the
BACK button.
Use the buttons to move upwards and downwards from one
line to another. Use to change settings.
You can also use the numeric buttons on the remote control to
select a line in a menu and to enter numeric values.
FIRST TIME INSTALLATION
The Welcome Menu
This picture indicates that you have started the installation pro-
cedure.
•Press OK on the remote control to start the Installation pro-
cedure.

GB 14
FIRST TIME INSTALLATION
Channel Search
The Channel Search procedure can be performed in two differ-
ent ways: Automatic Search or Manual Search.
Manual Search *
When you perform a Manual search you first need to enter some
parameters for the channel search to work.
The information you need to enter in this menu is available from
your Service Provider.
Frequency: Enter the frequency . If you enter the wrong figure(s),
erase with the button.
Transmission Mode: Select 2k or 8k.
Guard Interval: Select one of the available alternatives.
Network Search: Select Yes if you want to search on all frequen-
cies in a specific network.
•Press OK to start searching for channels. (See Channel Search
Progress”on the next page.)
Automatic Search *
•Start the Automatic search on by pressing OK.
* Frequency Offset
Select No and only the standard, fixed, channel frequencies will
be used at the search procedure. Under normal circumstances
this will be quite sufficient. Select Yes when you want the search
procedure to be more accurate. The fixed channel frequency will
still be searched, but this time with two extra steps; ±167 kHz
from the fixed frequency. NOTE! You have to select Yes or No
before you start the search procedure.
RF modulator type
If the Mediamaster is connected to the TV with a RF cable, you
must select the right RF modulator alternative, which is depend-
ent on the country where the Mediamaster is being used.
Select Normal (PAL B/G) for all countries except the UK.
Select UK (PAL I) when the box is used in the UK.
If you get picture but no sound, the RF modulator selection might
be wrong.

GB 15
FIRST TIME INSTALLATION
Finishing the first time installation
The channels found at the search procedure will now be saved.
A message telling that the installation procedure is completed will
be shown on the screen.
Press OK in order to start watching channels from the box.
Channel Search Progress
This menu will be shown as long as the Mediamaster is search-
ing for channels to download
All channels found will be listed in two columns on the screen;
TV channels in one column and Radio channels in the other.
Please note that the search procedure may take a few minutes.
When the search procedure has ended, the screen will show how
many TV and Radio channels have been found.
Press OK.
Time adjustment
The time is adjusted by using the buttons, ±1/2 an hour at a
time.
You can also adjust the minutes by using the buttons.
Press OK to finish the first time installation, see below.

GB 16
VIEWING MODE
General Information
The following describes the basic functions of your Mediamaster
while watching terrestrial digital TV .
Some of the functions described here are dependent on the
Service Provider and can only be used if they are included in
the transmitted programme information.
Please note, that during the Channel Search procedure, the
Mediamaster may download a large number of channels. This
may include channels from various Service Providers, also those
to which you do not have access unless you have a Smartcard
from one of those Service Providers.
If you select a programme to which you do not have access, you
will get a message on the screen. This message may vary, de-
pending on Service Provider and used Smartcard/CA Module.
While viewing, the current channel number will be shown on the
front panel display.
In addition to the normal functions like switching the Media-
master in/out of standby, changing the volume etc. there are
some other useful functions which will be explained in this part
of the manual.
You can always leave a menu at any time you want, without
affecting any settings, by pressing the EXIT button.
Information about
the next programme
Information about
the current pro-
gramme
Channel number
and name
Current
time
Channel
list
Age limit
information
12
Programme Information
Every time you change channels you will receive programme in-
formation for a few seconds.
The information may include:
Current time.
Channel list.
Channel number and name.
Name of the current and next programme.
The start and total time of the current programme.
A bar, indicating the elapsed time of the current programme.
Recommended lowest age limit for watching the programme.
The start and total time of the next programme.
Programme information will only be available if it is included in
the transmission. Otherwise a “No information available”mes-
sage will be shown.
You may change channel lists with the buttons.
Application Download (“Open TV” applications)
From some channels it is possible to download specific pro-
gramme applications such as games and various information.
Channels which provide these services will show a symbol in the
upper left corner of the screen. By pressing the red button on the
remote control you start the download of the application.
To close an application and return to watch TV, press the P+ or
P- button on the remote control.
Press the red button on the
remote control to start down-
loading an Open TV application

GB 17
VIEWING MODE
Information. The “i” Button
The Mediamaster has the ability to display information about pro-
grammes currently being broadcast as well as those being broad-
cast next.
By pressing the “i”button while watching TV you will get a spe-
cial Programme Information Banner. Select channel with or
the numeric buttons.
The “i” symbol is coloured blue when displaying information
about the current channel, and red when information for another
channel is shown.
•In this view, you can select to get information about the cur-
rent and next programme by using the buttons.
•You can leave the menus at any time and return to viewing TV
by pressing EXIT.
Guide
Press MENU Select GUIDE. Press OK and you get access to the
Nokia EPG (Electronic Programme Guide) which will give the ti-
tles of the current and next programmes on different channels.
Use the buttons to move the cursor to another programme.
Use the buttons to get information about next programmes.
Use the double arrow buttons to move a page at a time up and
down.
When a line is highlighted, you can get more information about
this programme by pressing the “i”button.
In certain circumstances you may get an EPG from your Service
provider instead. If so, please follow the instructions given in that
menu.
•Press “i”again to get more information about the current pro-
gramme.
•If a lot of information is available you can use the double ar-
row button to see the rest of the text.
•Press “i”a third time to return to TV mode.
*

GB 18
List of Channels
At the channel search procedure, 2 Channel lists named “TV
channels”and “Radio channels”are created. A Radio list will only
be created and highlighted when radio channels were available
to download.
In the Channel lists scrambled channels are marked with a pic-
ture of a Smartcard (if this information is transmitted in the sig-
nal).
If you have performed a new channel search the new channels
found will be marked with a star in the “Channels”list.
Locked channels will be marked with a padlock.
While viewing TV or listening to a radio channel you get access
to the respectively Channel list by pressing OK. The lists can also
be selected in the main menu.
At the top of the menu you will see the name of the list. The cur-
rent list is the one in which the channel you are watching right
now is located.
•If the list contains a large number of channels, you can close
networks to reduce the number of channels. You open/close
a network by marking it and pressing . A closed network is
indicated with .
•Change channel lists with .
•You can change channel by stepping with the buttons or
enter the channel number with the numeric buttons on the re-
mote control.
•To change one channel list page at a time, use the double ar-
row buttons.
•Press OK when a channel name is highlighted to start watch-
ing to it.
•You can also get more information about a marked (highlighted)
channel by pressing the “i”button.
VIEWING MODE
Options. The green button
By pressing the OPTION button, you open a menu in which it is
possible to enter temporary settings. A menu will only appear
if the programme contains any options to set or change.
Settings made in this “options menu”are only valid for the pro-
gramme you currently are watching. If you leave the programme
and return to it again, the temporary settings will be gone.
Audio Language
Select among the different languages being broadcast.
Subtitle Language
Select among different subtitle languages. If you select OFF, you
will not get any subtitling at all.
Network
name
Channel number
and name
Name of the
Channel list
Indicates a
closed network
Indicates a
scrambled chan-
nel

GB 19
VIEWING MODE
TV Release (0)
With the 0button you can toggle between:
digital terrestrial TV
analogue terrestrial TV
video (the video must be switched on)
(This is only valid if the units are connected via SCART cables, and
not by a RF connection.)
Video Recording
Please note, that during the recording of a programme, every-
thing shown on the screen will be registered! For example, if you
call up a menu from the Mediamaster on the screen, the menu
will be recorded!
The TEXT Button (Teletext)
•Pressing the TEXT button will open a Teletext page (if Teletext
is transmitted.) Select teletext pages with the numeric buttons
on the remote control.
•You can also quickly step to the different page alternatives
shown in any page by pressing .
•Press OK on a selected number to go to that page.
•Press EXIT, BACK or TEXT to return to TV mode.
•The 0button will show the index page (normally page 100.)
will show the next or previous teletext page.
•You can use the double arrow buttons to browse through the
pages you just have visited.
On most new TV sets you can use the TV’s remote control to
open and control the teletext functions while watching digital TV
channels. (The function is called VBI insertion.) NOTE: Also see
“Subtitles”settings on pages 26 and 27.
Format
If you have a TV set with a 4:3 picture format, and the transmis-
sion is in 16:9, you can select Fullscreen or Letterbox to change
display format.
Fullscreen will fill up the screen vertically, but cut off some infor-
mation from the left and right sides of the picture.
Letterbox will give a complete picture, but leave black areas at
the top and bottom.
EXIT TV
This button has double functions.
While watching TV: The TV/ function is used to switch from
TV to radio mode and vice versa.
When you have entered a menu, the EXIT function is used to
leave the menu at any time without changing anything.
Channel number
Analogue TV mode
Video mode. (The Video
must be switched ON)

GB 20
MAIN MENU
General Information
Many of the functions of the Mediamaster are available from the
Main Menu.
•Press MENU to open it.
TV and Radio Channels
Please refer to “List of channels”on page 18.
Edit Channels
From these menus you can create and edit channel lists. You can,
among other things, create favourite lists; add, delete, rename
and arrange the order of the channels within the lists.
In the All TV list the channels are normally presented network
by network. First the name of the network. Then the name of the
regional network transmitter from which you are receiving the
channels.
The All TV list can contain a lot of channels. By creating your own
favourite lists you can make channel handling a bit more conven-
ient.