Nora Lighting NUTP3 Series User manual

Installation Instructions ***URGENT: READ PRIOR TO ATTEMPTING INSTALLATION***
SPECIALTY LIGHTING - RGB LED TAPE LIGHT
ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
Item# Description Rating
NUTP3 Series 24V RGB LED Tape Light 24V / 2.5W/ft.
NUPT6 Series 12V RGB LED Tape Light 12V / 2.5W/ft.
INSTALLATION SHOULD BE CARRIED
OUT BY YOUR LOCAL ELECTRICIAN.
Installation Instructions:
1. Decide where you want to place the LED tape light.
2. The tape light has a 3M™ self-adhesive backing, ensure the surface area that you intend to adhere the tape light to is clean and dry. Simply
remove the backing strip and carefully lay the tape light in place working from one end to the other ensuring there are no raised sections.
3. Using a lint-free cloth gently press between the LEDs on the tape to remove any air bubbles and activate the adhesive, make sure you do
not press on the LEDs themselves as this could damage the joint.
6505 Gayhart St., Commerce, CA 90040
www.NoraLighting.com
Page 1 of 2
Caution:
• Alwaysturnoffpowerpriortoinstallationorreplacement.
• TapeLightcontactsareveryfragile,handlewithcare.
• DonotturnonTapeLightwhileonthespool,maycausethetapelighttooverheatandmeltorignite.
• DonotpressdirectlyontheLEDsthemselves,asitmaycausedamage.
• Donotusetheproductinapotentiallycombustiveenvironments.
• Donotcoverthisproductasthecoveringmaycausethetapelighttooverheatandmeltorignite.
• Donotoperatewiththetapelighttightlycoiled.
• Donotroutethecordortapelightthroughwalls,doors,windowsoranylikepartofthebuildingstructure.
• Donotuseifthereisanydamagetothelightorcordinsulation.Inspectperiodically.
• Donotsubmergethetapelightinliquids,orinstalltheproductcloserthan9.8'(3meters)fromaswimmingpoolsurface.
• Securethetapelightusingonlythe3M™tape,hangers,clips,orNATHR-680AluminumChannel(soldseparately).Donotsecurethis
product or its cord with staples, nails, or like means that may damage the insulation or permanently attach to the building structure.
Wiring Instructions to Controller:
1. Controller(soldseparately)hasmaleplugandtheRGBLEDTapeLighthasthefemaleconnector.Plugmaleconnectorintofemale
connector together.
Polarity: TapeLightmustalwaysbeconnectedfacingupwardandredarrowonconnectorsmustalwaysfaceup.(Fig.1)
Separable every 12":
1. The LED tape light may be separated every 12". Every 12" section is shrink wrapped around the connection point. Cut the silicone to
 revealtheconnectionpoint.(Fig.3)
2. Twoseparatedtapelightmaybeconnected,butmustbeshrinkwrapped(Page2)tomaintainETLListing.
Cutting Instructions - See back side for joining instructions:
1. TheLEDtapelightmaybecutevery6"or6LEDs.Every6"sectionisseparatedbycutline.(Fig.2)
2. Carefully cut the tape light along the line, be careful not to press on the LEDs as this could damage the joint.
3. When cutting the end of the tape light, shrink wrap the open cut with NATL-400.
Fig.1 Fig.2 Fig.3
May be cut
every 6" or 6
LEDs at cut line

ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
INSTALLATION SHOULD BE CARRIED
OUT BY YOUR LOCAL ELECTRICIAN.
6505 Gayhart St., Commerce, CA 90040
www.NoraLighting.com
Page 2 of 2
Shrink Wrap Installation Instructions to ensure ETL wet location listing:
1. Have one male and one female end of the tape light.
2. Insert male end of the tape light into the pre-cut shrink wrap supplied by Nora Lighting.
3. Connect the male and female connections inside the shrink wrap. Adjust silicone so both tape lights have sufficient shrink wrap covering
black insulation.
4. Heatthesilicone(hairdryer,orflameatleast6"awayfromtape/silicone)aroundentireconnectiontowraptheconnectiontightlyand
maintain ETL wet location listing.
Fig.1 Fig.2 Fig.3 Fig.4
Installation Instructions ***URGENT: READ PRIOR TO ATTEMPTING INSTALLATION***
SPECIALTY LIGHTING - RGB LED TAPE LIGHT
Item# Description Rating
NUTP3 Series 24V RGB LED Tape Light 24V / 2.5W/ft.
NUPT6 Series 12V RGB LED Tape Light 12V / 2.5W/ft.