Nora Lighting NUTP13 Series User manual

6505 Gayhart Street, Commerce, CA 90040
TEL [phone] | www.noralighting.com | e-mail: [email protected]
© 2021 Nora Lighting, Inc. All rights reserved. Instructions subject to change without notice.
Installation Instructions
NUTP13 Series
120V Continuous IP65 Rated LED Tape Light
032321P1-3
IS-NUTP13-R04
READ PRIOR TO ATTEMPTING INSTALLATION
ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
INSTALLATION SHOULD BE CARRIED OUT BY YOUR LOCAL ELECTRICIAN
SAVE THESE INSTRUCTIONS
WARNING - When using outdoors; use portable lighting products, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Be sure the electrical power to the circuit has
been disconnected before installing this electrical system. When connecting to outdoor circuit, make sure outlet/circuit includes Ground Fault Circuit Interrupter (GFCI) protection.
IMPORTANT SAFETY INSTRUCTIONS: READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Always turn off power prior to installation or replacement
• Do not cover luminaire as this may cause the tape light to overheat, melt or ignite
• Do not operate luminaire when tape light is tightly coiled
• Do not puncture, cut, shorten or splice the luminaire
• Do not route the cord or luminaire through walls, doors, windows or any like part of the
building structure
• Do not use if there is any damage to the luminaire or cord insulation (inspect periodically)
• Do not submerge luminaire in liquids or use the product in the vicinity of standing water or
other liquids
• Secure the tape light using only the mounting clips (provided) or channel (ordered
separately). Do not secure luminaire or cord with staples, nails, or like means that may
damage the insulation or permanently attach to the building structure.
• Do not subject luminaire to continous flexing
1. Affix mounting brackets (two required per foot) to surface.
2. Mount tape light inside brackets.
3. Close the upper cover of the mounting clips.
1. Place channel (ordered separately) on the desired mounting surface and make the appropriate mounting holes
(minimum of three holes).
2. Align and drill the aluminum channel holes.
3. Place channel onto mounting surface and insert screws (not included) through holes into surface.
NOTE: NUTP13 does not have adhesive backing. Apply 3M™ adhesive double sided tape
(ordered separately: NUTP13-ADHTAPE) when using tape in aluminum channels in indoor applications only.
4. Peel the film from one side of the 3M™ adhesive and apply to the back of the tape light.
5. Peel the remaining film to mount the tape light onto the aluminum channel.
6. Place the tape light into the aluminum channel and gently press down on the tape light to firmly secure.
7. Attach the lens to the aluminum channel.
8. Add end caps to complete installation.
MOUNTING INSTALLATION
ALUMINUM CHANNEL INSTALLATION
Mounting Clips

6505 Gayhart Street, Commerce, CA 90040
TEL [phone] | www.noralighting.com | e-mail: [email protected]
© 2021 Nora Lighting, Inc. All rights reserved. Instructions subject to change without notice.
Installation Instructions
NUTP13 Series
120V Continuous IP65 Rated LED Tape Light
032321P2-3
IS-NUTP13-R04
READ PRIOR TO ATTEMPTING INSTALLATION
ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
INSTALLATION SHOULD BE CARRIED OUT BY YOUR LOCAL ELECTRICIAN
1. Make sure power is off
2. Connect cord and plug into receptacle (Note: When used outdoors, connect to GFCI outlet)
3. Turn power back on.
1. Do not unplug by pulling on cord. Grasp plug and remove from the receptacle or other outlet device.
2. Slide to open fuse cover and remove fuse carefully.
3. Warning: Risk of fire! Replace fuse only with 8 Amp, 125V fuse (included)
4. Close fuse cover
5. Warning: Risk of fire! Do not replace attachment plug. Contains a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
CORD AND PLUG INSTALLATION
FUSE REPLACEMENT
Cord and Plug
Neutral
Line
Note: Luminaire has a polarized plug (wider pin for neutral and other for line) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not use an extension cord unless plug can be fully inserted. Do not alter or replace the plug.
Slide open to
access fuse
Replacement Fuse
1. Make sure power is off
2. Pull luminaire’s hardwire cable to junction box and connect to supply wires according to NEC code
3. Turn power back on.
HARDWIRE INSTALLATION
Hardwire Cable
BENDING
WARNING: Single bend of 90° shall not exceed the minimum inside radius of 2" (50mm) as specified in the figure below..
WARNING: Do not bend on horizontal plane
WRONGWRONG
CORRECT
MINIMUM INSIDE BEND RADIUS = 2"

6505 Gayhart Street, Commerce, CA 90040
TEL [phone] | www.noralighting.com | e-mail: [email protected]
© 2021 Nora Lighting, Inc. All rights reserved. Instructions subject to change without notice.
Installation Instructions
NUTP13 Series
120V Continuous IP65 Rated LED Tape Light
032321P3-3
IS-NUTP13-R04
READ PRIOR TO ATTEMPTING INSTALLATION
ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
INSTALLATION SHOULD BE CARRIED OUT BY YOUR LOCAL ELECTRICIAN
1. Turn all power off before installation.
2. Connect surge protector (NATL-IP65/SP - ordered separately) to supply wires and LED tape light hardwire cable (Note: Surge protector not compatible with cord & plug).
3. Installation complete.
SURGE PROTECTOR INSTALLATION
REQUIRES: NATL-IP65/SP (Ordered Separately)
LED TAPE
LIGHT
JUNCTION BOX (BY OTHERS)
SUPPLY
CONNECTION
GROUND
NEUTRAL
NATL-IP65/SP
LINE