Nordson High flow fb User manual

Instruction Sheet

1997 Nordson Corporation

Issued 2/97 Manual 32-15

P/N 107 987C

High Flow and 100 PLUSFB Powder Pumps

The Nordson High Flow and 100 PLUS Powder Pumps are highly

efficient venturi-type pumps designed primarily for pipe-coating (fusion

bond) applications. Both pumps are designed to lift fluidized powder out

of a feed hopper, atomize the powder stream and deliver it to a powder

spray gun.

Disassembly of the pumps is simple. The venturi nozzles, throat, and

holder are held into the body, and the body onto the adapter, with

interference fits provided by silicone O-rings.

3215001A

4

3

1

2

Fig. 1 High Flow and 100 PLUS powder pumps

1. Hopper

2. Fluidized powder 3. Flow rate air 4. Atomizing air

1. Description

2

High Flow and 100 PLUS FB Powder Pumps

1997 Nordson Corporation

107 987C

Issued 2/97

Manual 32-15

See Figure 2. Use the following steps to install the pumps.

1. If the pumps are to be mounted on a Nordson Model HTM hopper,

locate the 28 mm (1.10 in.) hole used to mount the pump. If using

another hopper type, make a hole in the top of the hopper for the

pick-up tube (8) using a 19 mm (3/4in.) conduit punch. This punch

will provide the 28 mm (1.10 in.) hole required for installation.

NOTE: The pump must be mounted above the powder level.

3215002A

ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ

9

8

123 4

6

7

11

10

5

Fig. 2 Pump installation

1. 8 mm (5/16 in.) OD polyethylene air

tubing

2. Pump

3. Clamp

4. Delivery hose

5. Pump adapter

6. Hopper

7. Fluidizing plate

8. Pick-up tube

9. Conduit nut

10. Atomizing air

11. Flow rate air

2. Insert the pump adapter (5) into the hole in the hopper (6).

3. Tighten the grounding nut (9) on the pump adapter.

2. Installation

3

High Flow and 100 PLUS FB Powder Pumps

1997 Nordson Corporation

Issued 2/97 Manual 32-15

4. Screw the pick-up tube (8) into the pump adapter. The end of the

pick-up tube usually extends 25–50 mm (1–2 in.) above the fluidizing

plate (7). Cut the pick-up tube to proper length if necessary.

5. Place the pump (2) on the pump adapter.

6. Connect the 8 mm OD polyethylene tubing (1) to the atomizing and

flow air fittings (10). The atomizing air fitting is the upper fitting, and

the flow air fitting is the lower fitting.

NOTE: Older installations of the High Flow Powder Pump use 3/8in.

polyethylene tubing. Older installations of the 100 PLUS FB Powder

Pump use 1/4in. OD polyethylene tubing. The 8 mm polyethylene tubing

is used with all newer models.

NOTE: The High Flow model of the pump will use a 19 mm (3/4in.) ID

polyurethane delivery hose. The 100 PLUS model of the pump will use a

12.7 mm (1/2in.) ID polyurethane delivery hose.

NOTE: The polyurethane powder delivery tubing is very stiff and may

need to be heated before it can be placed onto the pump outlet fittings.

Use an air gun to heat the end of the tubing to soften it and make it

pliable.

Typical operating air pressures are:

Atomizing: 0.7 bar (10 psi)

Flow: 2.7 bar (40 psi)

These pressures are an average starting point and can be adjusted

higher or lower until the desired delivery volume and cloud density is

achieved.

Disconnect the atomizing and flow air tubing and blow out the pump and

powder feed tubing daily. The pump should be disassembles and

thoroughly cleaned periodically.

NOTE: Reassemble the pump with care, so as not to cut or damage the

O-rings.

WARNING: Do not use compressed air to blow powder off skin

or clothing. Compressed air injected under the skin can cause

serious injury or death.

Blow parts clean with low pressure compressed air and wipe with a

clean, lint free cloth. The cloth may be moistened with a non-toxic

solvent if necessary, but do not immerse the O-rings in the solvent.

Solvents will swell and damage the O-rings. Do not scrape parts with

sharp objects as burrs or scratches on powder contact surfaces will

contribute to powder buildup or impact fusion. Inspect parts for wear and

replace if necessary.

2. Installation

(contd.)

3. Operation

4. Maintenance

4

High Flow and 100 PLUS FB Powder Pumps

E1997 Nordson Corporation

107 987C

Issued 2/97

Manual 32-15

See Figure 3.

Item Part Description Quantity Note

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

—

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

118 829

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Pump, powder, hi-flow, FB

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

972 277

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SElbow, male, 8 mm tube x 1/4thread

ÁÁÁÁÁ

2

ÁÁÁÁÁ

2

ÁÁÁÁÁ

118 842

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNozzle, air, atomizing, hi-flow

ÁÁÁÁÁ

1

ÁÁÁÁÁ

3

ÁÁÁÁÁ

118 831

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SHousing, pump, powder, hi flow

ÁÁÁÁÁ

1

ÁÁÁÁÁ

4

ÁÁÁÁÁ

118 834

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SThroat, venturi, powder, hi flow, w/O-rings

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

5

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

986 111

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SSRetaining ring, exl., invert, 0.625 in. ID

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

6

ÁÁÁÁÁ

940 142

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SSO-ring, silicone, 0.500 x 0.625 x 0.063 in.

ÁÁÁÁÁ

2

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

7

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

940 184

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.750 x 0.875 x

0.063in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

A

ÁÁÁÁÁ

8

ÁÁÁÁÁ

973 571

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SPlug, pipe, 1/4NPT

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

9

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

940 148

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.875 x 1.062 x

0.094in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

A

ÁÁÁÁÁ

10

ÁÁÁÁÁ

118 833

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SHolder, throat, hi-flow

ÁÁÁÁÁ

1

ÁÁÁÁÁ

11

ÁÁÁÁÁ

939 459

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SClamp, hose

ÁÁÁÁÁ

1

ÁÁÁÁÁ

12

ÁÁÁÁÁ

118 832

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

STube, wear, holder, hi-flow

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

13

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

940 147

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.500 x 0.625 x

0.063in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

4

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

A B

ÁÁÁÁÁ

14

ÁÁÁÁÁ

118 836

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNozzle, air, flow, hi-flow pump

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

NS

ÁÁÁÁÁ

Á

ÁÁÁ

Á

972 183

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

SElbow, male, 3/8tube x 1/4thread

ÁÁÁÁÁ

Á

ÁÁÁ

Á

2

ÁÁÁÁÁ

Á

ÁÁÁ

Á

C

NOTEA:Black silicone O-rings are electrically conductive. Do not substitute non-conductive O-rings.

B:Used on items 2 and 14.

C:Optional fitting shipped with pump. Used in place of the 8 mm tube fittings on air nozzles, for use with

older EXP-100 control units and 3/8in. OD air tubing.

NS: Not Shown

5. Parts

High Flow FB Powder Pump

5

High Flow and 100 PLUS FB Powder Pumps

1997 Nordson Corporation

Issued 2/97 Manual 32-15

3215003A

4 7 9

10

12

14

13

6

83

211

5

1

Fig. 3 High Flow FB Powder Pump

High Flow FB Powder Pump

(

contd.)

6

High Flow and 100 PLUS FB Powder Pumps

E1997 Nordson Corporation

107 987C

Issued 2/97

Manual 32-15

See Figure 4. Use this list to order parts for the 100 PLUS FB Powder

Pump.

Item Part Description Quantity Note

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

—

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

237 011

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Pump, powder, 100 PLUS, FB

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

972 276

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SElbow, male, 8mm x 1/8thread

ÁÁÁÁÁ

2

ÁÁÁÁÁ

2

ÁÁÁÁÁ

939 108

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SMarker, clip, “A” (for atomizing air nozzle)

ÁÁÁÁÁ

1

ÁÁÁÁÁ

3

ÁÁÁÁÁ

631 420

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNozzle, air, 0.073 in. ID

ÁÁÁÁÁ

2

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

4

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

940 129

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.375 x 0.500 x

0.063in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

4

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

A

ÁÁÁÁÁ

5

ÁÁÁÁÁ

249 502

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SHousing, pump, powder,

ÁÁÁÁÁ

1

ÁÁÁÁÁ

6

ÁÁÁÁÁ

114 221

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SThroat, venturi, Tivar, w/O-rings

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

7

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

986 100

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SSRetaining ring, ext., invert, 0.500 x 0.063 in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

8

ÁÁÁÁÁ

940 126

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SSO-ring, silicone, conductive, 0.750 x 0.875 x

0.063 in.

ÁÁÁÁÁ

2

ÁÁÁÁÁ

A

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

9

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

973 402

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SPlug, pipe, 1/8NPT

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

10

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

940 184

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.750 x 0.875 x

0.063in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

11

ÁÁÁÁÁ

249 506

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SHolder, throat

ÁÁÁÁÁ

1

ÁÁÁÁÁ

12

ÁÁÁÁÁ

249 507

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

STube, wear, holder

ÁÁÁÁÁ

1

ÁÁÁÁÁ

13

ÁÁÁÁÁ

940 163

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, 0.625 x 0.750 x 0.063 in.

ÁÁÁÁÁ

2

ÁÁÁÁÁ

14

ÁÁÁÁÁ

939 109

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SMarker, clip, “f” (for flow air nozzle)

ÁÁÁÁÁ

1

ÁÁÁÁÁ

NS

ÁÁÁÁÁ

972 119

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Elbow, male, 1/4tube x 1/8thread

ÁÁÁÁÁ

AR

ÁÁÁÁÁ

B

NOTEA:Black silicone O-rings are electrically conductive. Do not substitute non-conductive O-rings.

B:Optional fitting (not shipped with pump). Use in place of the 8 mm tube fittings on air nozzles, for use

with older EXP-100 control units and 1/4in. OD air tubing.

AR: As Required

NS: Not Shown

100 PLUS FB Powder Pump

7

High Flow and 100 PLUS FB Powder Pumps

1997 Nordson Corporation

Issued 2/97 Manual 32-15

3215004A

6 10

13

1

2 3 457

11

89

314

12

Fig. 4 100 PLUS FB Powder Pump

100 PLUS FB Powder Pump

(

contd.)

8

High Flow and 100 PLUS FB Powder Pumps

E1997 Nordson Corporation

107 987C

Issued 2/97

Manual 32-15

See Figure 5. Use these lists to order spare parts for the FB (fusion

bond) style pump mount and pick-up tube.

Item Part Description Quantity Note

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

—

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

180 777

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Mount, pump, w/pick-up tube, fixed, 18 in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

114 225

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SAdapter, pump

ÁÁÁÁÁ

1

ÁÁÁÁÁ

2

ÁÁÁÁÁ

941 185

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.875 x 1.062

ÁÁÁÁÁ

2

ÁÁÁÁÁ

A

ÁÁÁÁÁ

3

ÁÁÁÁÁ

942 161

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, 1.125 x 1.375 x 0.125

ÁÁÁÁÁ

1

ÁÁÁÁÁ

4

ÁÁÁÁÁ

142 382

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNut, ground, pump mount

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

5

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

180 778

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

STube, pick-up, 0.490 ID x 18 in.

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

NOTEA:Black silicone O-rings are electrically conductive. Do not substitute non-conductive O-rings.

Item Part Description Quantity Note

ÁÁÁÁÁ

—

ÁÁÁÁÁ

224 721

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Mount, pump, w/pick-up tube, fixed, 24 in.

ÁÁÁÁÁ

1

ÁÁÁÁÁ

1

ÁÁÁÁÁ

114 225

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SAdapter, pump

ÁÁÁÁÁ

1

ÁÁÁÁÁ

2

ÁÁÁÁÁ

941 185

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, conductive, 0.875 x 1.062

ÁÁÁÁÁ

2

ÁÁÁÁÁ

A

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

3

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

942 161

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, silicone, 1.125 x 1.375 x 0.125

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

1

ÁÁÁÁÁ

Á

ÁÁÁ

Á

ÁÁÁÁÁ

4

ÁÁÁÁÁ

142 382

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNut, ground, pump mount

ÁÁÁÁÁ

1

ÁÁÁÁÁ

5

ÁÁÁÁÁ

224 722

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

STube, pick-up, 0.490 ID x 24 in.

ÁÁÁÁÁ

1

ÁÁÁÁÁ

NOTEA:Black silicone O-rings are electrically conductive. Do not substitute non-conductive O-rings.

6. Spare Parts

9

High Flow and 100 PLUS FB Powder Pumps

1997 Nordson Corporation

Issued 2/97 Manual 32-15

3215005A

3

4

5

2

1

Fig. 5 Pick-up tube and assembly

6. Spare Parts

(contd.)

10

High Flow and 100 PLUS FB Powder Pumps

1997 Nordson Corporation

107 987C

Issued 2/97

Manual 32-15

Use this list to order tubing for the High Flow and 100 PLUS FB pump.

Part Description Quantity Note

ÁÁÁÁÁ

900 724

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Tubing, powder, polyurethane, 0.485 ID

ÁÁÁÁÁ

AR

ÁÁÁÁÁ

A

ÁÁÁÁÁ

900 725

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Tubing, powder, polyurethane, 0.735 ID

ÁÁÁÁÁ

AR

ÁÁÁÁÁ

B

ÁÁÁÁÁ

173 101

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Tubing, air, polyethylene, 8 mm OD, natural

ÁÁÁÁÁ

AR

ÁÁÁÁÁ

173 102

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Tubing, air, polyethylene, 8 mm OD, black

ÁÁÁÁÁ

AR

ÁÁÁÁÁ

NOTE A: Used with 100 PLUS FB pump.

B: Used with High Flow FB pump.

AR: As Required

Original copyright date 1990. 100 PLUS, Nordson and the Nordson logo are registered trademarks of Nordson

Corporation.

Tivar is a registered trademark of Menasha Corporation.

Powder Delivery Hose and Air

T

ubin

g

Nordson High Flow FB User manual

Popular Water Pump manuals by other brands