Nortel NORSTAR M7324 Parts list manual

© 2001 Nortel Networks
P0941600 Issue 01
Business Communications Manager
M7324 User Card

Page 3
Your Business Communications Manager M7324 Telephone
Using Button
Inquiry Check what is programmed on your memory buttons. 1. Release all calls or lines with dial tone.
2. Press Ä¥â.
3. Press the button(s) that you want to check and read the display.
4. Press Äwhen finished.
Adjusting display
contrast 1. Press Ä¥à.
2. Press UP or DOWN for the level you want.
3. Press OK when finished.
Selecting a ring
type and volume
level
1. Press Ä¥ß.
2. Press Ú, Û, Ü, Ý, or NEXT to hear the different ring types.
3. While the telephone is ringing, press Ãto adjust the volume
level.
4. Press OK to store the volume level and ring.
Mounting the
telephone The M7324 telephone can be placedonany level surface. It cannot be wall-mounted.
Using display
buttons Three display buttons appear directly below the display. When they are active, these
buttons are labelled in capital letters on the
bottom line of the display. In Business
Communications Manager documents,
display buttons are shown as underlined,
capital letters: for example, OK.
Memory and line buttons
have labels for one-touch dialling, feature operation, or line access
Display
shows the time, date, and call information;
guides you while using features;
tilts for easy viewing. The lower line of the
display is reserved for display
button instructions.
Display buttons
Dial pad
Volume control
Hold button
Feature button
starts or ends a feature
Release button cancels active call
Indicators
appear beside active lines and features

Page 4
Making and answering calls
Answering calls Answering calls using the handset
When your telephone rings, or ¼flashes beside an Intercom or line button:
1. Lift the handset.
OR
Press the button beside the flashing ¼before lifting the handset.
Answering calls using Handsfree
When your telephone rings, or ¼flashes beside an Intercom or line button:
1. Press ©.
Making calls Depending upon the dialing mode programmed on your telephone, you may
have to lift the handset before making a call.
ÂExternal calls using numbered line buttons
1. If you do not have an external Prime line, press a line button.
2. Dial your call.
ÆExternal calls using Intercom buttons
1. Lift the handset.
2. If ¼appears beside an Intercombutton, enter a line pool access code.
OR
Press an Intercom button without ¼, then enter a line pool access code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press Æ.
2. Dial your call.
Note: Line pool access codes and extension numbers are supplied by your
System Administrator.
Making calls using Handsfree
1. Press ©instead of lifting the handset.
úHolding Calls
1. Press ú. The ¼flashes beside the line on hold.
2. Press the line button with the flashing ¼to return to the call.
Automatic hold
Calls are put on hold automatically when you switch from one line to another.
Exclusive hold
Use Exclusive Hold (Äú ) to keep a call on hold so that it
can be retrieved only at your telephone.
©This button operates your telephone’s built-in microphone and speaker.Your
System Administrator can program Handsfree for your telephone.
Switching between Handsfree and handset
1. Press ©and replace the handset to switch to Handsfree.
2. Pick up the handset toswitch back.
Using Mute
1. Press ©to turn the microphone OFF.
2. Press ©again to turn the microphone ON.

Page 5
Programming memory buttons
Remember: Press Ä¥â to check a memory or line button.
Programming
memory buttons External Autodial
1. If you are on a call or a line with dial tone, press úor ¨.
2. Press Ä¥Ú.
3. Press a memory button.
4. Dial the external number.
5. Press OK to store the number.
6. Label your new button.
Internal Autodial
1. If you are on a call or a line with dial tone, press úor ¨.
2. Press Ä¥Û.
3. Press a memory button.
4. Dial the extension number.
5. Label your new button.
Features
1. If you are on a call or a line with dial tone, press úor ¨.
2. Press Ä¥Ü.
3. Press a memory button.
4. Press Äand the feature code.
5. Label your new button.
Erasing memory buttons
1. If you are on a call or a line with dial tone, press úor ¨.
2. Press Ä¥Ú.
3. Press the memory button you want to erase.
4. Press OK to erase the button.
About memory
buttons Memory buttons are the buttons with
labels other than line or Handsfree
buttons. Memory buttons store
telephone numbers or feature codes to
give you one-touch dialling or feature
activation. You can change the function
of a memory button by programming it
with a new number orfeature.
If you have programmed a memory
button with an extension number, the
indicator comes on when the number is
busy.

Page 6 P0941600 Issue 01
Setting up the telephone
Notice These telephones now conform to the latest standards in relation to the
positioning of Q and Z on the number keys. The Q appears on key number 7
and the Z appears on key number 9.
ATTENTION Before attempting to carry
out any work on the telephone, ensure
that the line cord is unplugged from the
wall socket.
To remove any of the cords, squeeze the
release latch on the plug and gently pull
the plug from the socket.
Connect the handset cord to the jack
labelled with the telephone icon and
route the cord as shown.
If you are using a headset, route the
cord along the channel in the base and
connect the cord to the telephone jack
that is marked with the headset icon.
Route the line cord through the stand
and connect the cord to the telephone
jack that is marked with the jack icon.
Attach the stand using either pair of
slots; to raise the back of the telephone
to its highest position, use these slots.
Once the above work is complete, plug
the line cord back into its wall socket.
Connecting the cords
Connect to jack
from distribution block
Connect to receiver