Nortel NORSTAR M7324 User manual

© 2000 Nortel Networks
P0908514 Issue 03
Enterprise Edge
M7324
Quick Reference Guide

Page 1 Enterprise Edge M7324 Quick Feature Guide
Your Enterprise Edge M7324 Telephone
Using Button
Inquiry Check what is programmed on your memory buttons.
1. Release all calls or lines with dial tone.
2. Press ƒ•‚.
3. Press the button(s) that you want to check and read the display.
4. Press ƒwhen finished.
Adjusting display
contrast 1. Press ƒ•‡.
2. Press UP or DOWN for the level you want.
3. Press OK when finished.
Selecting a ring
type and volume
level
1. Press ĥfl.
2. Press ⁄, ¤, ‹, ›, or NEXT to hear the different ring types.
3. While the telephone is ringing, press √to adjust the volume
level.
4. Press OK to store the volume level and ring.
Mounting the
telephone The M7324 telphone can be placed on any level surface. It cannot be
wall-mounted.
Using display
buttons
Three display buttons appear directly
below the display. Whenactive, these
buttons appear in capital letters on
the second line of the display. In this
guide, display buttons appear as
underlined, capital letters: for
example, OK.
Display
shows the time, date, call information,
Indicators
appear beside lines and features.
Feature button
starts or ends a feature.
Release button
cancels active calls.
Hold button
Dial pad
Volume control
Memory and line buttons
are buttons with indicators for one
touch dialing, feature operation or line access.
Display buttons
and guides you. The lower line of the display
is reserved for display button instructions.
Contrast level 2
Contrast level 2Contrast level 2
Contrast level 2
DOWN UP OK
DOWN UP OKDOWN UP OK
DOWN UP OK Display button
message
Display buttons
Display message

Page 2 Enterprise Edge M7324 Quick Feature Guide
Making and answering calls
Answering calls Answering calls using the handset
When your telephone rings, or ºflashes beside an Intercom or line
button:
1. Lift the handset.
ORPress the button beside the flashing ºbefore lifting the handset.
Answering calls using Handsfree
When your telephone rings, or ºflashes beside an Intercom or line
button:
1. Press ©.
Making calls Depending upon the dialing mode programmed on your telephone, you
may have to lift the handset before making a call.
¬External calls using numbered line buttons
1. If you do not have an external Prime line, press a line button.
2. Dial your call.
∆External calls using Intercom buttons
1. Lift the handset.
2. If ºappears beside an Intercom button, enter a line pool access code.
ORPress an Intercom button without º, then enter a line pool access code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press ∆.
2. Dial your call.
Note: Line pool access codes and extension numbers are supplied by
your System Administrator.
˙Holding Calls
1. Press ˙.The ºflashes beside the line on hold.
2. Press the line button with the flashing ºto return to the call.
Automatic hold
Calls are put on hold automatically when you switch from one line to
another.
Exclusive hold
Use Exclusive Hold (ƒ˙) to keep a call on hold so that it
can be retrieved only at your telephone.

Page 3 Enterprise Edge M7324 Quick Feature Guide
Making and answering calls continued
©This button operates your telephone’s built-in microphone and
speaker. Your System Administrator can program Handsfree
for your telephone.
Switching between Handsfree and handset
1. Press ©and replace the handset to switch to
Handsfree.
2. Pick up the handset to switch back.
Using Mute
1. Press ©to turn the microphone OFF.
2. Press ©again to turn the microphone ON.
Making calls using Handsfree
1. Press ©instead of lifting the handset.
Notice This telephone now conforms to the latest standards in
relation to the positioning of Q and Z on the number keys. The
Q appears on key number 7 and the Z appears on key
number 9.

Page 4 Enterprise Edge M7324 Quick Feature Guide
Programming memory buttons
Remember: Press ƒ•‚ to check a memory or line
button.
Programming memory
buttons External Autodial
1. If you are on a call or a line with dial tone, press ˙or
®.
2. Press ƒ•⁄.
3. Press a memory button.
4. Dial the external number.
5. Press OK to store the number.
6. Label your new button.
Internal Autodial
1. If you are on a call or a line with dial tone, press ˙or
®.
2. Press ƒ•¤.
3. Press a memory button.
4. Dial the extension number.
5. Label your new button.
Features
1. If you are on a call or a line with dial tone, press ˙or
®.
2. Press ƒ•‹.
3. Press a memory button.
4. Press ƒand the feature code.
5. Label your new button.
Erasing memory buttons
1. If you are on a call or a line with dial tone, press ˙or
®.
2. Press ƒ•⁄.
3. Press the memory button you want to erase.
4. Press OK to erase the button.
About memory
buttons Memory buttons are the buttons with
labels other than line or Handsfree
buttons.Memorybuttonsstoretelephone
numbers or feature codes to give you
one-touch dialling or feature activation.
You can change the function of a
memory button by programming it with a
new number or feature.
If you have programmed a memory
button with an extension number, the
indicator comes on when the number
is busy.

Page 5 Enterprise Edge M7324 Quick Feature Guide P0908514 Issue 03
Setting up the telephone
ATTENTION Before attempting to carry
out any work on the telephone, ensure
that the line cord is unplugged from the
wall socket.
To remove any of the cords, squeeze the
release latch on the plug and gently pull
the plug from the socket.
Connect the handset cord to the jack
labelled with the telephone icon and route
the cord as shown.
If you are using a headset, route the cord
along the channel in the base and connect
the cord to the telephone jack that is
marked with the headset icon.
Route the line cord through the stand and
connect the cord to the telephone jack
that is marked with the jack icon.
Attach the stand using the slots on the
back of the telephone.
Once the above work is complete, plug
the line cord back into its wall socket.
Connecting the cords
Connect to jack
from distribution block
Connect to receiver