Northern IPPTZ30XIR User manual

IPPTZ30XIR·Quick Start Guide
i
Quick Start Guide
About this Manual
The Manual includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website.
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY
WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
TO THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS
PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.

IPPTZ30XIR·Quick Start Guide
ii
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

IPPTZ30XIR·Quick Start Guide
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger
or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety regulations,
fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. For standard of the power
adapter, please refer to the specification manual for details. The power consumption cannot be
less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle the
speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places
subject to shock (ignorance can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire or
electrical shock will occur. For working temperature, please refer to the specification manual for
details.
The dome cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
Warnings Follow these
safeguards to prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

IPPTZ30XIR·Quick Start Guide
iv
Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of sensor at the
same time.
Please use the provided glove when open up the dome cover, avoid direct contact with the dome
cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do not
use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the speed dome to the factory with the original wrapper. Transportation without
the original wrapper may result in damage on the speed dome and lead to additional costs.

IPPTZ30XIR·Quick Start Guide
v
Table of Contents
1.1 Connecting Cables .....................................................................................6
1.2 Wall Mounting ..........................................................................................6
1.2.1 Installing the Bracket ............................................................................................................. 6
1.2.2 Installing Micro SD Card ........................................................................................................ 8
1.2.3 Speed Dome Installation........................................................................................................ 8
2.1 Wiring ..................................................................................................... 10
2.2 Activating the Speed Dome ..................................................................... 10
2.2.1 Activation via Web Browser................................................................................................. 10
2.2.2 Activation via SADP Software .............................................................................................. 11
2.3 Modifying the IP Address ........................................................................ 12

IPPTZ30XIR·Quick Start Guide
6
1Installation
Warning: Do not power the speed dome up until the installation is finished. To ensure the safety of
personnel and equipment, all the installation steps should be done with power supply off.
Before you start:
Check the package contents and make sure that the device in the package is in good condition and
all the assembly parts are included.
When carrying the speed dome, do not directly pull waterproof group cables. Otherwise,
the waterproof or circuit performance may be affected.
1.1 Connecting Cables
The cable interfaces of network speed dome are shown in two following figures. The cables are
distinguished by different colors. Please refer to the labels attached on the cables for identification.
RED AC24V
YELLOW/GREEN
BLACK AC24V
Red AC24V
Black AC24V
Yellow&Green GND
Purple AUDIO-IN
Black GND
Pink AUDIO-OUT
Yellow/Gray ALARM-IN6
Yellow/Red ALARM-IN7
Yellow/Black ALARM-GND
White/Black ALARM-COM1
White/Red ALARM-OUT1
Network
RED AC24V
YELLOW/GREEN
BLACK AC24V
Figure 1-1 Cables of 5-inch and 7-inch IR Network Speed Dome
1.2 Wall Mounting
1.2.1 Installing the Bracket
The speed dome can be installed to a thread interface or non-thread interface bracket. The
non-thread bracket is highly recommended.
When you select a thread bracket, please install the pendent adapter (supplied) between the
bracket and speed dome. Any mismatch problems shall be taken responsibility by the user.

IPPTZ30XIR·Quick Start Guide
7
The dimension of pendant adapter is G11
2.
For cement wall, you need to use the expansion screw to fix the bracket.
For wooden wall, you can just use the self-tapping screw to fix the bracket.
Please make sure that the wall is strong enough to withstand at least 8 times the weight of the
dome and the bracket.
The wall must be thick enough to mount the expansion screws.
There are several ways to install the speed dome. In this section, the non-thread bracket installation
is taken as an example. Refer to the following steps for details:
Steps:
1. Get the bracket and screws from the packing box as shown follows.
Figure 1-2 Wall Mounting Bracket and Accessories
2. Drill 4 φ12 screw holes in the wall according to the hole locations of the bracket, and then insert
M8 expansion screws into the screw holes.
Figure 1-3 Drill Screw Hole and Insert Expansion Screw
3. Secure the bracket with 4 hex nuts and washers.

IPPTZ30XIR·Quick Start Guide
8
Figure 1-4 Drill Screw Holes
Please take water-proof measures when installing outdoor speed domes.
1.2.2 Installing Micro SD Card
Purpose:
The speed domes are with built-in micro SD card slots which are for local storage with micro SD
cards. There are four types of speed dome listed as follows.
Refer to the following steps to install the micro SD card.
7-inch IR network speed dome: The micro SD card slot is inside the rear cover. Outdoor mini
IR network speed dome is taken as an example here. Refer to the following steps to install
the micro SD card.
Steps:
1. Loosen 4 screws in the rear cover. Remove the rear cover.
2. Insert the SD card to the slot in the correct direction. Make sure the SD card is clicked into place.
3. Attach the rear cover back to the speed dome. Secure the rear cover with 4 screws.
SD Card Slot
Figure 1-5 Micro SD Card Slot
1.2.3 Speed Dome Installation
7-inch IR Network Speed Dome Installation
Steps:
1. Remove the protective sticker from the speed dome.

IPPTZ30XIR·Quick Start Guide
9
Protective
Sticker
Figure 1-6 Remove Sticker
2. Hook the two ends of the safety rope to the back box of the speed dome and the bracket
respectively.Route the cables through the bracket as shown follows.
3. Loosen the lock screws on the bracket as shown below.
4. Align the speed dome with bracket and rotate it counterclockwise or clockwise to the bracket
tightly as shown below.
Lock
Screw
Safety Rope
Push
Rotate
Figure 1-7 Align to the Bracket
5. Use L-wrench to tighten the lock screws to secure the speed dome and the bracket.
Figure 1-8 Tighten the Lock Screws

IPPTZ30XIR·Quick Start Guide
10
6. Remove the protective film on the IR light.
2Setting the Dome over the LAN
You shall acknowledge that the use of the product with Internet access might be under
network security risks. For avoidance of any network attacks and information leakage, please
strengthen your own protection. If the product does not work properly, please contact with
your dealer or the nearest service center.
To ensure the network security of the speed dome, we recommend you to have the speed
dome assessed and maintained termly. You can contact us if you need such service.
2.1 Wiring
To view and configure the speed dome via LAN (Local Area Network), you need to connect the
network speed dome in the same subnet with your PC. Then, install the SADP or client software to
search and change the IP of network speed dome.
The following figure shows the cable connection of network speed dome.
Network
Speed Dome
Switch Internet
NVR
PC
Figure 2-1 Wiring over LAN
2.2 Activating the Speed Dome
Purpose:
You are required to activate the speed dome first by setting a strong password for it before you can
use the speed dome.
Activation via Web Browser, Activation via SADP, and Activation via client software are supported. In
the following sections, activation via web browser and SADP will be taken as examples. You may
refer to the user manual of the speed dome for the details of activation via client software.
2.2.1 Activation via Web Browser
Steps:
1. Power on the speed dome, and connect the speed dome to the network.

IPPTZ30XIR·Quick Start Guide
11
2. Input the IP address into the address bar of the web browser, and click Enter to enter the
activation interface.
The default IP address of the speed dome is 192.168.1.64.
Figure 2-2 Activation Interface(Web)
3. Create a password and input the password into the password field.
STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong
password of your own choosing (using a minimum of 8 characters, including upper case
letters, lower case letters, numbers, and special characters) in order to increase the
security of your product. And we recommend you reset your password regularly,
especially in the high security system, resetting the password monthly or weekly can
better protect your product.
4. Confirm the password.
5. Click OK to activate the speed dome and enter the live view interface.
2.2.2 Activation via SADP Software
SADP software is used for detecting the online device, activating the device, and resetting the
password.
Get the SADP software from the supplied disk or the official website, and install the SADP according
to the prompts. Follow the steps to activate the speed dome.
Steps:
1. Run the SADP software to search the online devices.
2. Check the device status from the device list, and select an inactive device.

IPPTZ30XIR·Quick Start Guide
12
Figure 2-3 SADP Interface
3. Create a password and input the password in the password field, and confirm the password.
STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong
password of your own choosing (using a minimum of 8 characters, including upper case
letters, lower case letters, numbers, and special characters) in order to increase the
security of your product. And we recommend you reset your password regularly,
especially in the high security system, resetting the password monthly or weekly can
better protect your product.
4. Click OK to save the password.
You can check whether the activation is completed on the popup window. If activation failed,
please make sure that the password meets the requirement and then try again.
2.3 Modifying the IP Address
Purpose:
To view and configure the speed dome via LAN (Local Area Network), you need to connect the
network speed dome in the same subnet with your PC. Then, install the SADP software or client
software to search and change the IP of network speed dome. We will take modifying the IP
Address via SADP software as an example to introduce the IP address modification.
Steps:
1. Run the SADP software.
2. Click to select an active device.
Please refer to the section 2.2 Activating the Speed Dome to activate the speed dome if it
is inactive.

IPPTZ30XIR·Quick Start Guide
13
3. Change the device IP address to the same subnet with your computer by either modifying the
IP address manually or checking the checkbox of Enable DHCP.
Figure 2-4 Modify the IP Address
4. Input the password and click Save to activate your IP address modification.

IPPTZ30XIR·Quick Start Guide
14
3Accessing via Web Browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 /
Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.02 and above version, Mozilla
Firefox 5 and above version and Google Chrome 18 and above version
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network speed dome, e.g., 192.168.1.64
and press the Enter key to enter the login interface.
3. Activate the speed dome for the first time using, refer to the section 2.2 Activating the Speed
Dome.
4. Input the user name and password and click .
The admin user should configure the device accounts and user/operator permissions properly.
Delete the unnecessary accounts and user/operator permissions.
The device IP address gets locked if the admin user performs 7 failed password attempts (5
attempts for the user/operator).
Figure 3-1 Login Interface
5. Install the plug-in before viewing the live video and managing the network speed dome. Please
follow the installation prompts to install the plug-in.
You may have to close the web browser to finish the installation of the plug-in.

IPPTZ30XIR·Quick Start Guide
15
Figure 3-2 Download Plug-in
Figure 3-3 Install Plug-in
6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to
login.
For detailed instructions of further configuration, please refer to the user manual of network
speed dome.
0503001050324