Novexx Solutions LTSI User manual

01/13 Rev. 5.05-01 USER / SERCICE MANUAL
LTSI
Mounting and setting the LTSI
Required Components .................................. 2
Fitting the Applicator ..................................... 3
Setting the Applicator ....................................4
„Must“-parameters ..................................... 4
„Can“-parameters ...................................... 4
Adjusting the Applicator Home Position .... 5
Setting the Dispense Position ................... 6

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI
LTSI Required Components
7
Required Components
Component Part number Picture
Basic module
LTSI 80/200 (fig.) A4787
Basic module
LTSI 80/400 A4788
Aluminium plate
(with screws 2x DIN912 M5x12
and 2x DIN912 M8x20) A2661
[Tab. 1] Required components to fit the LTSI to an 64-xx. The basic
module is only required in one version.

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI
LTSI Fitting the Applicator
8
Fitting the Applicator
Tools
Allen screwdriver 4 and 6mm
Mounting
1. Switchofftheprinteranddisconnect thepowerplug
from the power outlet!
2. Remove the flange cover from the mounting flange
[1A]
3. Boltthe adapterplate [2A]ontothemountingflange
(2x M5x16).
4. Bolt the applicator to the aluminium plate (2x
M8x20 with lock washers) [3].
5. Plug the applicator cable to the printer [3A].
[6] Applicator mounting flange (A).
[7] Adapter plate (A) ready mounted.
[8] LTSI ready mounted and connected.
A
A
A

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI
LTSI Setting the Applicator
9
Setting the Applicator
„Must“-parameters
„Can“-parameters
WARNING!
Danger of getting hands crushed at the following locations:
• Between applicator pressure plate and printer dispensing edge.
• Between applicator pressure plate and conveyor (if applicable).
During operation, keep your hands away from the moving area of the applicator.
Switch off the printer before any servicing or repair work.
Parameter Setting
DISPENSER PARA > Start source USI
DISPENSER PARA > Dispensing edge long
DP INTERFACE > Interface type USI applicator
DP INTERFACE > Start print mode Level low active a
a) This setting is imperative, if parameter DP INTERFACE > Apply mode is set to
„After start sig.“
DP INTERFACE > End print mode Mode 1
DP INTERFACE > Internal inputs Enabled
[Tab. 2] These parameter settings are imperative for the printer
operation with an applicator.
Parameter
DISPENSER PARA > Application mode
DP INTERFACE > Start print mode a
a) This setting is only arbitrary, if parameter DP INTERFACE >
Apply mode is set to „After print“.
DP INTERFACE > Apply mode
[Tab. 3] These parameters can be used to adapt the applicator ope-
ration to the application.

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI
LTSI Setting the Applicator
10
Adjusting the Applicator Home
Position
After fitting the applicator, the home position of the ap-
plicator must be checked and adjusted if necessary.
When viewed from the side, the applicator plate must
stand slightly above and in front of the dispensing edge
[4].
The following guide values may used for the dis-
tances from the dispensing edge:
• Horizontal: approx. 1 mm
To adjust: Shifting of the left aluminium plate [5A]
– upwards --> shifts the home position further
away from the dispensing edge.
– downwards --> shifts the home position closer
to the dispensing edge.
• Vertical: approx. 0.5 mm
To adjust: Shifting of the right aluminium plate [5B]
– upwards --> shifts the home position upwards.
– downwards --> shifts the home position down-
wards.
[9] Applicator in home position.
[10] Adjusting the home position. Remove the gaiter to get to tho-
se aluminium plates.
AB

01/13 Rev. 5.05-01 USER / SERVICE MANUAL Mounting and setting the LTSI
LTSI Setting the Applicator
11
Setting the Dispense Position
The label can either be dispensed so that it is entirely
free from the carrier material, or it can remain adhering
to the carrier material via a small strip when the feed
stops [6].
The required width of this strip depends on the type of
further processing and is set via a printer parameter.
When using the applicator, the dispensing position
should be set so that the label is just released when dis-
pensed, i.e. so that it no longer adheres to the carrier
material.
Advancingthecarriermaterialtoofar cancause strings
of adhesive to pull the label down with them.
Setting via the PRINT PARAMETERS >Dispenseposition pa-
rameter.
[11] Adjusting the dispense position.
Dispensed label Dispense position
Dispensing edge
Backing paper