NPK GH06 User manual

HYDRAULIC HAMMER
OPERATORS MANUAL
GH SERIES HAMMERS
GH06 GHS2
GH07 GH3
GH1 GH4
GH2 GH6
© Copyright 2009 NPK Construction Equipment, Inc. www.npkce.com H050-9640A 03-09.doc 03/09
"Use Genuine NPK Parts
”
7550 Independence Drive
Walton Hills, OH 44146-5541
Phone [phone]
Toll-free [phone]
Fax [phone]

- 1 -
CONTENTS
SAFETY..........................................................................................................................2
INTRODUCTION............................................................................................................. 4
CARRIER MACHINE COMPATIBILITY .......................................................................... 5
HAMMER SPECIFICATIONS .........................................................................................6
HYDRAULIC INSTALLATION.........................................................................................7
PREVENTION OF CONTAMINATION........................................................................8
HYDRAULIC QUICK DISCONNECTS........................................................................9
MOUNTING INSTALLATION........................................................................................ 11
LUBRICATION..............................................................................................................12
GREASING PROCEDURE....................................................................................... 12
CORRECT GREASE AND GREASE INTERVALS...................................................13
NPK HAMMER GREASE.......................................................................................15
AUTOLUBE SYSTEMS............................................................................................. 15
LUBRICANT TERMS AND DEFINITIONS................................................................ 16
START-UP OPERATION.............................................................................................. 18
HAMMERS THAT ARE NEW, REBUILT, OR HAVE BEEN INACTIVE ....................18
BEFORE STARTING THE HAMMER....................................................................... 19
DAILY START-UP PROCEDURE.............................................................................19
OPERATION.................................................................................................................20
SAFE OPERATING INSTRUCTIONS.......................................................................20
OPERATING TECHNIQUES & PRECAUTIONS ......................................................21
ROUTINE INSPECTION AND MAINTENANCE............................................................ 26
WEEKLY INSPECTION ................................................................................................ 27
TOOLS..........................................................................................................................28
STANDARD TOOLS................................................................................................. 28
ACCESSORY TOOLS .............................................................................................. 28
CHANGING THE TOOL............................................................................................29
MAXIMUM TOOL TO TOOL BUSHING CLEARANCE.............................................30
TOOL RETAINING PIN INSPECTION......................................................................32
TOOL INSPECTION................................................................................................. 33
TORQUE VALUES FOR HAMMER FASTENERS........................................................ 34
GAS CHARGE .............................................................................................................. 35
NITROGEN GAS PRESSURE..................................................................................35
GAS CHARGE ADAPTER........................................................................................ 35
GAS CHARGING KIT ...............................................................................................36
CHECKING THE GAS PRESSURE..........................................................................37
CHARGING THE HAMMER...................................................................................... 39
DISCHARGING THE GAS PRESSURE ...................................................................40
WARRANTY REGISTRATION FOR NEW UNITS ........................................................ 42
WARRANTY STATEMENT........................................................................................... 43
STORAGE OF HYDRAULIC HAMMER........................................................................ 44
NOTES AND RECORDS ..............................................................................................45

- 2 -
SAFETY
Safety notices in NPK Instruction Manuals follow ISO and ANSI standards for
safety warnings:
DANGER (red) notices indicate an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING (orange) notices indicate a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION (yellow) notices indicate a potentially hazardous situation,
which, if not avoided, may result in minor or moderate injury.
ATTENTION (blue) notices in NPK Instruction Manuals are an NPK
standard to alert the reader to situations which, if not avoided, could
result in equipment damage.
WARNING and BASIC OPERATING INSTRUCTIONS decals are included with each
NPK hammer and installation kit. Decals must be installed in the cab, visible to the
operator while operating the hammer.
STAY CLEAR, PRESSURE VESSEL, GAS PRESSURE and TOOL SHARPENING
decals are installed on all NPK hammer models. Keep them clean and visible. NPK will
provide decals free of charge as needed.
1. Operator and Service personnel must read and understand the NPK INSTRUCTION
MANUAL to prevent serious or fatal injury.
2. FLYING DEBRIS CAN CAUSE SERIOUS OR FATAL INJURY.
•Keep personnel and bystanders clear of hammer while in operation.
•Do not operate HAMMER without an impact resistant guard between HAMMER
and operator. NPK recommends LEXAN®or equivalent material, or steel mesh.
Some carrier manufacturers offer demolition guards for their machine. Check
with the carrier manufacturer for availability. If not
available, please call NPK.
3. Do not hardface or sharpen the tool point with a cutting
torch. Excessive heat from torching or welding can
cause embrittlement, breakage, and flying pieces.
Resharpen by milling or grinding only, using sufficient
coolant.

- 3 -
SAFETY
4. Fully extend the tool while charging the HAMMER with nitrogen gas. Be sure that
the retaining pin is installed. STAY CLEAR OF TOOL POINT WHILE CHARGING.
5. Do not disassemble a HAMMER before discharging the hammer gas pre-charge.
6. USE NITROGEN GAS ONLY! Store and handle nitrogen tanks per OSHA
regulations.
7. Avoid high pressure fluids. Escaping fluid under pressure can penetrate the skin
causing serious injury. Relieve pressure before disconnecting hydraulic or other
lines.
8. Operate HAMMER from operator’s seat only.
9. Match HAMMER size to carrier according to NPK recommendations. The carrier
must be stable during hammer operation and during transport.
See CARRIER MACHINE COMPATIBILITY section of the NPK instruction manual.
10. Do not make any alterations to the TOOL without authorization from NPK
Engineering.
11. Use proper lifting equipment and tools when handling or servicing the HAMMER.
12. Wear ear protection and safety glasses when operating the hammer. Consult
OSHA/MSHA regulations when applicable.
13. Beware of flying metal pieces when driving Boom Pins.
14. If modifications are to be made, do not alter the HAMMER without authorization
from NPK Engineering!
15. Use only genuine NPK replacement parts. NPK specifically disclaims any
responsibility for any damage or injury that results from the use of any tool or parts
not sold or approved by NPK.
For further safety information, consult the AEM Hydraulic Mounted Breakers Safety
Manual, AEM form MB-140 (NPK P/N H050-9600), which is furnished with every NPK
hammer. To request an additional copy, please contact NPK at 800-225-4379 or
Internet at www.npkce.com.

- 4 -
INTRODUCTION
NPK is a leading manufacturer of HYDRAULIC HAMMERS, and has the most complete
product line available anywhere. The success of NPK is due to our commitment to
quality, dependability and long life. The HYDRAULIC HAMMER has many unique
designed features and it is a company philosophy that the NPK HYDRAULIC HAMMER
can be brought to "like new” condition long after competitive products are scrapped.
You can feel confident that you have purchased the best value available.
This comprehensive operator’s manual contains instructions for operating and
maintaining NPK HYDRAULIC HAMMERS. This manual includes helpful information for
obtaining the full potential and efficiency from NPK HYDRAULIC HAMMERS. Please
read this manual thoroughly to understand the NPK HAMMER and its operating
principles before using it.
For additional information or help with any problem encountered, please contact your
NPK authorized dealer.
Whenever repair or replacement of component parts is required, only NPK parts should
be used. NPK is not responsible for failures resulting from substitution of parts not sold
or approved by NPK.

- 5 -
CARRIER MACHINE COMPATIBILITY
These carrier weight ranges are intended as a guideline only. Other factors, such as
stick length, counterweights, undercarriage, etc., must be taken into consideration.
Mounting a HAMMER that is too heavy for the carrier machine
can be dangerous and damage the machine. Verify carrier
stability with hammer before transport or operation.
Mounting a HAMMER that is too small for the carrier machine can damage the
HAMMER, cause tool breakage and void Warranties. Please consult NPK Engineering
for specific detailed information.
CARRIER WEIGHT lbs. (kg)
HAMMER MOUNTING RECOMMENDED RANGE
MODEL STYLE (lb) (kg)
GH06 Excavator 2,200 – 4,400 1,000 – 2,000
Skid Steer 2,400 – 3,500 1,100 – 1,600
GH07 Excavator 2,800 – 5,500 1,300 – 2,500
Skid Steer 3,000 – 5,500 1,350 – 2,500
GH1 Excavator 5,400 – 9,000 2,450 – 4,100
Skid Steer 5,000 – 7,500 2,300 – 3,400
GH2 / GHS2 Excavator 6,600 – 12,000 3,000 – 5,500
Skid Steer 6,000 – 9,000 2,700 – 4,100
GH3 Excavator 8,800 – 15,000 4,000 – 7,000
Skid Steer 8,000 – 14,000 3,600 – 6,400
GH4 Excavator 13,000 – 22,000 6,000 – 10,000
GH6 Excavator 22,000 – 31,000 10,000 – 14,000
*Specifications are subject to change without notice.

- 6 -
HAMMER SPECIFICATIONS
TOOLWORKING
WEIGHT MOUNTING STYLE DIA WORKING
HAMMER
MODEL IMPACT ENERGY
CLASS
FREQUENCY LENGTH
ft lb bpm lbs (Kg) in (mm) in (mm)
GH06 150 480 – 1200 500 (225) Skid Steer 1.7 (42) 12.2 (311)
235 (107) Excavator
GH07 200 500 – 1200 550 (250) Skid Steer 1.9 (47) 13.1 (333)
270 (125) Excavator
GH1 350 550 – 1100 750 (340) Skid Steer 2.2 (57) 13.6 (346)
450 (205) Excavator
GH2 / GHS2 500 500 – 1300 800 (365) Skid Steer 2.6 (66) 14.4 (367)
525 (240) Excavator
GH3 750 500 – 1150 1075 (490) Skid Steer 3.0 (76) 16.1 (408)
800 (365) Excavator
GH4 1300 400 – 1050 1250 (570) Excavator 3.4 (86) 18.0 (458)
GH6 2000 500 – 800 2150 (980) Excavator 4.2 (106) 20.0 (500)
GAS CHARGE
PRESSURE 5
OIL FLOW HYDRAULIC
OPERATING
PRESSURE 1
CIRCUIT
RELIEF
minimum 2Cold 3Hot
4
HAMMER
MODEL
gpm (L/min) psi (bar) psi (bar) psi (bar) psi (bar)
GH06 2.5 – 7 (10 – 25) 1650 (115) 2150 (150) 350 (24) 405 (28)
GH07 4 – 9 (15 – 35) 1500 (105) 2000 (140) 350 (24) 405 (28)
GH1 7 – 13 (25 – 50) 1750 (120) 2250 (155) 350 (24) 405 (28)
GH2 / GHS2 7 – 17 (25 – 65) 2250 (160) 2750 (190) 350 (24) 405 (28)
GH3 12 – 26 (45 – 100) 1900 (130) 2400 (165) 350 (24) 405 (28)
GH4 13 – 32 (50 – 120) 2200 (150) 2700 (185) 375 (26) 435 (30)
GH6 24 – 40 (90 – 150) 2400 (165) 2900 (200) 390 (27) 450 (31)
*Specifications subject to change without notice.
NOTES:
1. Hydraulic operating pressure maximum is inlet pressure at the hammer with the oil at
operating temperature and with the gas charge set at the hot operating pressure. See
CHECKING THE HYDRAULIC PRESSURES section in Service Manual.
2. Circuit relief pressure is at least 500 psi (35 bar) above hammer operating pressure.
3. Cold gas charge is the initial set with the hammer at ambient temperature.
4. Hot gas charge is checked after 1 to 2 hours of running and with a system oil
temperature of 140°to 180°F (60°to 80°C). This is the preferred check.
5. Pressures listed are maximum. Use tolerance of minus 25 psi (2 bar).

- 7 -
HYDRAULIC INSTALLATION
NPK INSTALLATION KITS are available for virtually all compatible backhoe loaders,
excavators, and skid steers. Complete parts and instructions for the hydraulic
installation of the NPK HYDRAULIC HAMMER including valving and/or controls, hoses
and fittings, boom and stick tubing, and clamps are provided.
HAMMER LINES
Typically, the pressure line is arranged on the left side of the boom and the return line
on the right side. Flow to the hammer is controlled from an auxiliary valve on the carrier
or from an NPK supplied valve. Hydraulic oil, generally, is routed back to the tank thru
the carrier’s oil cooler and filter.
HAMMER CONTROL VALVE
NPK uses two general types of control systems, depending upon the carrier model:
1. CONTROL SYSTEM USING THE CARRIER AUXILIARY OR SPARE VALVE
SECTION.
This type of installation utilizes an existing carrier valve. Any additional parts, such
as a mechanical linkage, hydraulic pilot actuators, flow control valves, etc., are
furnished in the NPK HYDRAULIC INSTALLATION KIT. Special hydraulic pressure
control valves are not required. The NPK HYDRAULIC HAMMER operating
pressure is self-regulating.
2. CONTROL SYSTEM USING THE NPK MULTIVALVE.
For carriers not equipped with a suitable auxiliary or spare valve section, the NPK
HYDRAULIC INSTALLATION KIT includes a solenoid operated, priority flow control
valve to operate the NPK HYDRAULIC HAMMER. The NPK MULTIVALVE is
specifically designed for the operation of boom mounted attachments.

- 8 -
ATTENTION
HYDRAULIC INSTALLATION
PREVENTION OF CONTAMINATION
1. A hydraulic hammer is harder on oil than using a bucket, so the oil is apt to
deteriorate and breakdown sooner. Neglect of the oil system can not only damage
the hydraulic hammer but also cause problems in the carrier which could result in
damaged components. Care should be taken to check for contamination of the oil
and to change it if it is found contaminated. Oil sampling at regular intervals is
highly recommended.
When the hydraulic oil shows low viscosity and bubbles, this indicates that the oil
is deteriorated. If the oil is dark brown and gives off an offensive odor, it is
severely deteriorated. Change the oil immediately.
When the oil is clouded, or the oil filter has become clogged, it indicates that the
oil is contaminated. Change the oil immediately!
To change the contaminated hydraulic oil, drain the hydraulic system completely
and clean components. Do not mix new oil with the old.
2. Do not allow any contamination to mix with the oil. Take special care in preventing
contamination from entering the hydraulic system through the hose or tube
connection when changing the hydraulic hammer with the bucket.
3. Low oil level will cause heat build-up, resulting in deterioration of the oil. Also, it may
cause cavitation due to air mixing with the oil, leading to a damaged hydraulic
hammer and carrier components. Keep the oil at the proper level at all times.
4. Do not use the hydraulic hammer at an operating temperature higher than 180°F
(80°C). The proper operating oil temperature range is between 120°F (50°C) and
180°F (80°C). Since contaminated cooler fins causes reduced efficiency of the
cooler, keep the cooler fins clean at all times. Check the hydraulic oil cooling system
to be sure it is working effectively. The use of a heat gun is the best way to evaluate
if the cooler is working properly.
5. Water in the hydraulic oil will lead to damage of the hydraulic hammer and carrier.
Drain off water and foreign matter from the hydraulic tank at specified intervals.
When out of service, the hydraulic hammer should be stored indoors.
CHANGING THE FILTER ELEMENT AND HYDRAULIC OIL
Change the filter element and hydraulic oil at the intervals described in the operation
manual of the skid steer or excavator, when using a hydraulic implement. Another
method is to set up an oil sampling schedule and change accordingly.

- 9 -
HYDRAULIC INSTALLATION
HYDRAULIC QUICK DISCONNECTS
NPK recommends against the use of non-NPK quick
disconnects on hydraulic circuits operating NPK Products.
1. The hydraulic pulsations caused by hydraulic hammer operating can cause internal
pieces of non-NPK quick disconnect to disintegrate. These pieces would migrate
into the hammer, causing damage.
2. If quick disconnects are used when the hammer is removed from the excavator, the
quick disconnects should be capped to keep them clean. If this is not done,
contamination in the disconnect will be flushed into the hammer when re-connected.
This, again, can cause damage.
3. Most quick disconnects create a restriction in the circuit. NPK Hammers are not
back pressure sensitive, but restrictions cause unnecessary heating of the oil. Also,
the pressure required to operate the hammer, plus the restriction in the disconnects
may push an older, low pressure, carrier machine to the limit of its hydraulic system.
This would interfere with proper hammer operation. However, the NPK approved
quick disconnects are properly sized so that the hammer operation is not
affected.
APPROVED CONNECTION (39) NOT RECOMMENDED CONNECTION Non-NPK Quick Disconnects (32)
NPK APPROVED CONNECTION QUICK DISCONNECTS (DX)
CONTACT YOUR NPK DEALER FOR ADDITIONAL INFORMATION ABOUT
NPK QUICK DISCONNECTS