Nuga N4 User manual

www.nuga.kr
185, Jiraeul-ro, Jijeong-myeon, Wonju-si,
Gangwon-do, Korea
TEL : [phone] / FAX : [phone]
http://www.nuga.kr
ENGLISH/ CE H/H / Rev. 03
2017.04.03
N4
User Manual
Thank you for purchasing this product.
Before use...
Please read the cautions for safety in the
user manual to use this product safely.
Quality Warranty Enclosed
[ ENGLISH ]
Tourmanium Product

 
N4
Cautions for Safety
Contents Cautions for Safety
Product Features
Product Manual Guide
Product Components
Product Frame Components
Screws for Assembly
Names and Functions of Product
Descriptions for Controller Buttons
Product Introduction
Before Product Installation
How to Assemble Product Frame
How to Install Product
Test Operations after Installation
Production Installation and Use
How to Store and Clean Product after Use
Check Indicator Window of Controller
How to Take Emergency Actions during Use
Self-check Items
Before any A/S Request
Product Specifications
Memo
Product Warranty
Product Storage and Care
How to Use Controller
How to Use Product by Mode
How to Use External Projector(Abdomen heating pad)
How to Use Low Frequency Pad
How to Use Product
How to Set Temperature for Auxiliary heating part
8
9
10
11
12
14
16
18
20
24
26
40
41
42
43
44
45
46
47
28
28
33
34
36
38
How to Use Product
Cautions for your safety
Disclaimer
· These cautions include descriptions for the safety of users and prevention
of any damage to properties among others.
· Read through the following details to use the product appropriately.
· This Manual classifies the risk level into following three degrees and the
following graphical symbols remind users of cautions for matters and
operations of concerns about any risk.
· The manufacturer, importer and/or agent shall not be responsible for any
problem and/or other damage to the product which has been caused
from the user’s fault or operation.
· Information in the user manual has been prepared on the basis of the current
product specifications.
· Details in the user manual might be different from those on the product.
· The product manufacturer will be adding and supplementing new functions
at any time and new technologies shall be applied to the product continuously
in the future as well.
· All the standards and functions are subject to change without any notice
to users to improve performance.
Interpretations on symbols
Caution
If there is a possibility of a minor injury or damage to goods due to
non-compliance.
Danger
If there is high possibility of death due to non-compliance.
Warning
If there is a possibility of an injury or death due to non-compliance.

 
N4
Danger
Put the projector cover on the
external projector while using the
external projector to keep the
projector from touching the skin
directly.
(Otherwise, it is likely that injuries
occur.)
Avoid pulling out the power cord
parts or touching the power plug
with the wet hands.
(Otherwise, it might cause
electrical shock or fire.)
Avoid using the product in a
closed place in presence of any
fuel and/or chemical.
(Otherwise, it might cause
injuries or fire.)
Do not use the device in areas that
are dusty or have severe
temperature fluctuations or where it
can come into contact with water.
(There are risks of electric shock
and fire.)
Anyone other than technicians
qualified for our company’s A/S
should not disassemble, repair or
modify the product for any reason.
(Otherwise, it might cause damage
to the product or electric shock
and/or fire.)
Immediately stop using the product
and turn off the power if there is any
thunder, lightning or earthquake.
(Otherwise, it might cause electrical
shock or fire.)
Avoid applying the external
projector directly to eyeballs to
prevent any risk.
(Otherwise, it might cause damage
to eyeballs.)
When using the device while lying
down on your stomach, do not use
it on your ribs and use it only on the
abdomen in manual mode.
Warning
Avoid placing inflammable
substances like candlelight, cigarette
light or liquors and/or vessels
containing water, heavy objects or
other objects on the product.
(Otherwise, it might cause fire.)
Avoid jumping on the product or
any other action to provide shocks
to the product.
(Otherwise, it might cause injuries
and/or damage to the product.)
Use the product after checking out
any damaged or worn-out cord.
(Otherwise, it might cause electric
shock, injury and/or damage to the
product.)
Do not insert many power plugs for
other products into a socket to be
used simultaneously.
(Otherwise, it might cause electric
shock, injury and/or damage to the
product.)
Do not allow children use the
product alone.
Apply the product to the area with
any surgery and/or treatment, after
consulting with the store or the
company from which you have
purchased the product.
Avoid using any band or belt that
does not come as one of
components from the purchase of
the product.
(Otherwise, it might cause damage
to the product.)
Avoid twisting the body while the
internal projector is being operated.
(Otherwise, it might cause
excessive influences to the spine.)
Avoid bending the power cord
excessively or pressing it down
with heavy objects.
Any persons meeting the following
criteria shall not use this device.
This device should not be used by a
pregnant woman or a patient with a
chronic disease, malignant tumor, high
fever, heart disease (pacemaker implant),
perceptual disorder, skin problem in the
target area, or spondylolysis
Cautions for Safety


N4
N4
Caution
Install the product horizontally.
Use the product in a range of
proper temperature as there is
risk of burns if the higher
temperature is set.
Do not use directly on skin
Connect the power supply after
connecting the controller first.
Be aware of danger of falling down
when you get on or off the product.
Any pregnant shall not use the
low frequency pad.
Move the product after separating
all the connecting lines including
the power supply when the product
is moved.
Check out the applied voltage
before any use and apply the power
plug only to a dedicated socket.
Please abide by defined time
and methods.
Separate the power cord while
the product is not being in use
for a long time.
]WGGGGGGGGGGGGGGGG]W
\WGGGGGGGGGGGGGGGG\W
[WGGGGGGGGGGGGGGGG[W
ZWGGGGGGGGGGGGGGGGZW
Product Features
Product Manual Guide
Product Components
Product Frame Components
Screws for Assembly
Names and Functions of Product Components
Descriptions for Controller Buttons
8
9
10
11
12
14
16
Product Introduction

 
N4
Product Features Product Manual Guide
Product Introduction
How to maximize the space
The main and sub mats are used horizontally.
When not using the device, fold the sub mat to maximize the space.
Internal Projector Designed in Human Engineering
A separate projector is built in around the cervical vertebrae as the
acupressure load can be equally distributed due to the design that the
internal projector can be rotated in a certain angle.
Conveniently Designed External Projector
External projector is designed in a size conveniently held and used with
a hand, which can be stored in a basket nicely during no use.
Internal Driving Method with Noise Reduction
There are few noises thanks to the minimized friction between the
internal projector and rail due to the specially designed guard rail which
can be used semi-permanently by minimizing the driving load.
Convenient Controller Holder
7KHFRQWUROOHUKROGHUSRVVLEOHRIÛURWDWLRQFDQEHXVHGFRQYHQLHQWO\
in any desired angle by the user.
Multifunctional Controller Integrated into One
Buttons in a size that can be identified at a glance are easy to use with less
wear due to the special materials, and button descriptions cannot be
easily erased.
Special Heater and Tourmanium
The Tourmanium is applied to the special heater.



How to refer to cautions for
safety
Refer to cautions to be kept during
the product use.
(Refer to Page 3 in this User Manual
for more details.)
How to Install the Product
(Refer to Page 24 in this User
Manual for more details.)
How to check out the product
components
(Refer to Page 10 in this User
Manual for more details.)
How to use the product
(Refer to Page 28 in this User
Manual for more details.)
How to Assemble the
Product Frame
(Refer to Page 20 in this User
Manual for more details.)

Hinge stopper L,R
 
Main base frame Leg support-1 Leg support-2
Auxiliary support bar

Sub frame base
Bolt setLever
N4
Product Introduction
Product Frame ComponentsProduct Components
Product frame
Outside cover Projector cover Low frequency pad Towel for
low frequency pad
Controller Basket
Main mat Sub mat External projector
Introduction
Please check out whether all the components are unpacked before
installing the product.
Please inquire from your supplier if there is any missing or damaged
component.
Some specifications and/or designs are subject to change for improving
the product performance.
i
Connection cable for sub matExtension band Power cord User manual
www.nuga.kr
N4
[ ENGLISH ]
User Manual
Thankyou for purchasing this product.
Beforeuse...
Pleaseread the cautions for safety in the
usermanual to use this product safely.
Tourmanium Product
QualityWarranty Enclosed
Abdomen heating pad
(Option)
FRAME LEG ASS'Y LEFT/ RIGHT
(Check the direction of the Left L and Right R
parts when assembling the device )
Left Right
Controller hanger Ass’y


N4
Screws for Assembly
Product Introduction
QJFDFT
B1-Wrench bolt M8X50
B2-FH-M5X18
B3-SEMS PH M5X12+S/W
B4- SEMS-PH-M5X10+S/W
B-5 TH-M4 X12
B-6 TH-M4 X 6
L-WRENCH
SCREW DRIVE
QJFDFT
QJFDFT
QJFDFT
QJFDFT
QJFDFT
QJFDF QJFDF


N4
Names and Functions of Product
ⴘThe connection for the power supply
on the main assembly and the power
input to the special heater
ⴠInternal projector
ⴡCervical Vertebrae Projector
ⴙAuxiliary heating part
ⴜExternal projector
(or Abdomen heating pad)
ⴟProduct frame
ⴞBasket
ⴝController and its holder
ྜConnector bay
ⴚLow frequency pad
The power supplies and signals are exchanged by connecting the power supply
cable to both the main mat and sub mat.
The Tourmanium is applied to the auxiliary heating part positioned on top of the
sub mat to increase the heating effects.
ⴙAuxiliary heating part
Connector bay connects the controller, the external projector and the
low frequency pad to the main assembly.
ⴛConnector bay
Low frequency pad has various effects including improvement of amyotrophia.
ⴚLow frequency pad
The main and sub mats have horizontal and foldable structures, and you can
use it while sitting or lying down.
When the external projector or low frequency pad is not being used, it can be
stored neatly in a basket. Also, users can put outer clothing in the basket before
using the product.
Cervical vertebrae projector is designed to move forward and backward at
a predetermined angle with insertion of the function to impart improved
acupressure and heat to the cervical vertebral region.
Since the internal projector is designed to move at a predetermined angle, the
acupressure load and heat are effectively distributed throughout the entire body.
In addition, the specially designed guard rail, which can be used semi-permanently
by minimizing the driving load, minimizes friction between the internal projector
and rail. Therefore, noises are minimized. .
ⴟProduct frame
ⴞBasket
ྡInternal projector
External projector(Abdomen heating pad) can be used to apply heat to desired
body part.
ⴜExternal projector
(Abdomen heating pad)
The controller is designed easy to use. In addition, the controller holder possible
RIÛURWDWLRQFDQEHXVHGFRQYHQLHQWO\LQDQ\GHVLUHGDQJOHE\WKHXVHU
ⴝController and its holder
Name Function
ⴘThe connection for the
power supply on the main
assembly and the power
input to the special heater

ྡྷCervical Vertebra
Projector
Product Introduction


N4
N4
Descriptions for Controller Buttons
Power button
108&3
Button to turn on/off the power
for the product, internal projector,
and cervical vertebrae projector
Power Button for
External Projector
Button to turn on/off the power
for the external projector
Temperature
Control Button for
Internal Project
Button to increase or decrease
temperature of internal projector
Auto/Manual
Switch Button
Button to set the operating
mode for the internal projector
/ cervical vertebrae projector
in Auto/Manual mode
"650
Indicator Window
for Temperature
and Condition of
Internal Projector
Window to display temperature
and error message of internal
projector / cervical vertebrae
projector (refer to Page 41 for
error messages)
Manual Mode
Button for Internal
Projector
Button to adjust the position
of internal projector up/down
during the manual mode
setting
13+&503
Power Button for
Low Frequency Pad
Button to turn on/off the power
for the low frequency pad
-08'3&2
Temperature
Control Button for
External Projector
Button to increase or decrease
temperature of external projector
Indicator Window
for Temperature
and Condition of
External Projector
Window to display temperature
and error message of external
projector (refer to Page 41 for
error messages)
Button to control
the intensity of
low frequency
Button to control the intensity of
low frequency to a range of the
low frequency pad
( weak~strong )
Before Product Installation
How to Assemble Product Frame
How to Install Product
Test Operations after Installation
18
20
24
26
Production Installation
and Use

 
N4
Before Product Installation
Production Installation and Use
Move the product after separating the power supply
from connecting lines if the product is moved.
(Otherwise, it might cause electric shock, injury
and/or damage to the product.)
Connect the power supply after connecting the
controller first.
(Otherwise, it might cause damage to the product.)
Install the product at a flat floor.
(Otherwise, it might damage the product.)
Do not drop or shock the product.
(Otherwise, it might damage the product.)
Check out the applied voltage before any use.
(Otherwise, it is likely that the electrical shock or
fire occurs.)
Do not place any inflammable substance on the
product, such as candle light or cigarette light.
(Otherwise, it is likely to cause the electrical
shock or fire.)
Avoid using the product in a closed place
with any fuel and/or chemical.
(Otherwise, it might cause injuries or fire.)
Do not install the product in a place with the
frequent access.
(Otherwise, the product might be damaged.)
Do not install the product in a place with
much moisture or water.
(Otherwise, the product might be damaged.)
Be careful not to expose the product to the
direct sunlight.
(Otherwise, the product might be damaged.)


Fixing the controller cover
Placement hole for the
controller cover
Fixing the frame legs

Fixing the main base frame
and the sliding frame


Fixing the Lever
 
5
2
2
1
3
#
#
4#
After placing the LEG SUPPORT1 (1) and
LEG SUPPORT2 (2) for the FRAME LEG
ASS'Y-R(3) and FRAME LEG ASS'Y-L(4),
use the fixing screw (B1) to fix in place.
Insert the CONTROLLER HANGER ASS'Y (5)
in the direction indicated in the figure and
fix it with a fixing crew (B2).
Assemble the main base frame (1) in the
direction indicated on the figure and place
the indicated groove area (Q”) on top of
the leg support-2 (2).
Turn the lever in the opposite direction
of the main base frame and place it on
the frame leg. Align it with the hole on the
end of the main base frame and fix it with
a fixing screw (B6).
N4
Insert it
inside the groove.
1
2
2
Production Installation and Use
How to Assemble Product Frame
Caution
Check the assembly direction of the Left
L and Right R parts before fixing the
device.
Caution
Make sure that the screw is placed accurately
into the hole. Caution
Make sure to insert it in the direction indicated
by the arrow.

 
)*/(&45011&33 )*/(&45011&3-
1
3
2
4
B4
B3
#
SUB FRAME BASE
N4
Production Installation and Use

Assembling the SUB FRAME
BASE ASS'Y
①Fix the HINGE STOPPER R into the
SUB FRAME BASE with a fixing screw (B3).
② Insert the AUXILIARY SUPPORT BAR into
the HINGE STOPPER R hole.
③ Insert the HINGE STOPPER L into the
AUXILIARY SUPPORT BAR(④) and fix it using
the SUB FRAME BASE fixing screw (B3).
Check the directionality when assembling
the HINGE STOPPER L and R.
Caution
Assembling the SUB MAT and
the SUB FRAME BASE ASS'Y

Grab the SUB FRAME BASE ASS'Y
as shown in the figure and fix it into the hole
on the bottom of the SUB MAT using a fixing
screw (B5).
Place a cloth on the floor when assembling
the SUB MAT.
In the presence of foreign matter and uneven
floor, damage may occur in the Tourmanium
heating unit.
Caution
Assembling the MAIN BASE
FRAME and SUB FRAME
BASE ASS'Y
Erecting the SUB MAT
Inserting the basket into the
main body

Grab the SUB FRAME BASE ASSY and
press the button, as shown in the figure,
to erect it perpendicularly.
Lock the basket in place at the four
places inside the leg frame, as shown
in the figure.


Align the SUB FRAME BASE ASS'Y
based on the locations of the fixing
screw holes on bottom of the MAIN
BASE FRAME, as shown in the figure,
and fix it using two fixing screws (B4)
on each side.
In order to ensure safety, make sure
to fully open the AUXILIARY SUPPORT
BAR.
Caution
Lock the basket in place outside the
rings of the MAIN BASE FRAME ASS'Y
LEG SUPPORT-2.
Caution
Button
Basket
LEG SUPPORT-2

 
ⴘⴙⴚ
N4
Production Installation and Use
How to Install Product
Installing the product frame
and main mat
Place the MAIN MAT on top of the MAIN
BASE FRAME, and bring it close to the two
supports below the MAIN BASE FRAME.

Attach the synthetic leather at the middle
connected to the MAIN MAT to the
VELCRO on the SUB MAT.
Covering the MAIN MAT
with an outside cover
Preparing product


Align the outside cover on the VELCRO
part on the front of the main mat and attach
it to the bottom side of the main device.
Insert the bottom part of the MAIN MAT
into the outside cover insertion hole and fix
it place using the VELCRO.
Take out the controller, power cord,
external projector, projector cover, and
low frequency pad.
Connect the power cables to the
MAIN MAT and SUB MAT, as shown
in the figure.
Caution
Make sure the groove in the cable
connection part is pointing upward.
If you do not connect the cable
accurately into the groove, it will lead
to malfunctions and device failure.


Caution
Make sure the power switch is turned
off when connecting the power cord.
Otherwise, it may cause malfunctions
and device failure.
Connecting the devices
to the connector
Connect thePower Cable
to the Sub Mat
Connect the power cord to the power
input part on the side of the MAIN
MAT and turn on the power switch.

Turning on the power
①Controller
②Low frequency pad
③External heating projector
Connect the above devices in this order.


N4
N4
Test Operations after Installation
How to Use Controller
How to Use Product by Mode
How to Use External Projector(Abdomen heating pad)
How to Use Low Frequency Pad
How to Use Product
How to Set Temperature for Auxiliary heating part
28
28
33
34
36
38
How to Use Product
Checking out the power
supply for the product



Caution
Ensure the power supply to be turned off
after use or during no use.
Otherwise, it might cause failure.
Controller for
main assembly
Controller for
external projector
ⴘ
ⴚ
ྜ
Turn on the power switch.
Checking out operations
of controller
① Press the power button on the controller
②Adjust temperature for the internal projector
(+ / – button)
③Adjust temperature for the external projector
(+ / – button)
④Sub mat power indication
Refer to ‘How to Use the controller’ for each
mode (Page 28)
Checking out operations
of sub mat
After turning on the power of the main assembly,
turn the dial clockwise to set a desired
temperature in the sub mat.

Using the product
Lay yourself down with your legs toward the
sub mat and press the Auto button in the
controller for the automatic operations in the
product.
Power switch
in the main assembly
Off On
Avoid sitting or placing an object on the
part of cervical vertebrae projector or
auxiliary heating part.
Otherwise, it might cause damage to the
product.
Do not sit or step on the synthetic leather
at the middle between the main and
auxiliary devices.

 
N4
How to Use Product
How to Use Controller
- How to Use Product by Mode
Auto ⴘMode
Round-trip
acupuncture function
ⴘPress the power button.
· Check out the connecting conditions
of the controller.
· Press the power button once : On
Press it once again : Off
Power supply
Auto ྙMode
ⴙPress the automatic button
(Auto LED lights up) to operate the
cervical vertebrae / internal projector.
There is no need to manipulate
the buttons during the operation
once it has started.
It will stop automatically after the
38-min massage.
Temperature control
ⴚControl temperature with +/- button.
(Moderate temperature: 55~60Ⳅ)
· Range of temperature setting for
internal projector: 40~70Ⳅ
(Temperature of cervical vertebrae
SURMHFWRULVIL[HGDWÛ&
· Temperature setting unit
40~70Ⳅ: Temperature setting per 1Ⳅ
GGG
Auto ⴙMode
Round-trip
massage function
ⴘPress the power button.
· Check out the connecting conditions
of the controller.
· Press the power button once : On
Press it once again : Off
Power supply
Temperature control
ⴚControl temperature with +/- button.
(Moderate temperature: 55~60Ⳅ)
· Range of temperature setting for
internal projector: 40~70Ⳅ
(Temperature of cervical vertebrae
SURMHFWRULVIL[HGDWÛ&
· Temperature setting unit
40~70Ⳅ: Temperature setting per 1Ⳅ
Auto ྚMode
ⴙPress the automatic button twice
(flashing of the automatic mode LED)
to operate cervical vertebrae /
internal projector. There is no need
to manipulate the buttons during the
operation once it has started.
It will stop automatically after the 38-min
massage.
Press the AUTO button to operate
AUTO 2 Mode during AUTO 1 Mode
is operating.

 
N4
How to Use Product
Temperature control
ⴙ3UHVVWKHŸEXWWRQWZLFHIODVKLQJ
RIWKHPDQXDOPRGH/('WRRSHUDWH
WKHFHUYLFDOYHUWHEUDHLQWHUQDO
SURMHFWRU7KHUHLVQRQHHGWR
PDQLSXODWHWKHEXWWRQVGXULQJWKH
RSHUDWLRQRQFHLWKDVVWDUWHG
,WZLOOVWRSDXWRPDWLFDOO\DIWHUWKH
PLQPDVVDJHEHWZHHQWKHWKRUDFLF
DQGFHUYLFDODUHDV
Auto ྛMode
Power supply
ⴘ3UHVVWKHSRZHUEXWWRQ
Â&KHFNRXWWKHFRQQHFWLQJFRQGLWLRQV
RIWKHFRQWUROOHU
Â3UHVVWKHSRZHUEXWWRQRQFH2Q
3UHVVLWRQFHDJDLQ2II
ⴚ&RQWUROWHPSHUDWXUHZLWKEXWWRQ
0RGHUDWHWHPSHUDWXUHaⳄ
·5DQJHRIWHPSHUDWXUHVHWWLQJIRU
LQWHUQDOSURMHFWRUaⳄ
7HPSHUDWXUHRIFHUYLFDOYHUWHEUDH
SURMHFWRULVIL[HGDWÛ&
Â7HPSHUDWXUHVHWWLQJXQLW
aⳄ7HPSHUDWXUHVHWWLQJSHUⳄ
0RYLQJ
SDWK
Auto ྛ0RGH
0DVVDJHIXQFWLRQEHWZHHQWKH
WKRUDFLFYHUWHEUDHDQGFHUYLFDOYHUWHEUDH
Power supply
Auto ྜMode
ⴙ3UHVVWKHźEXWWRQWZLFHIODVKLQJ
RIWKHPDQXDOPRGH/('WRRSHUDWH
WKHFHUYLFDOYHUWHEUDHLQWHUQDO
SURMHFWRU
7KHUHLVQRQHHGWRPDQLSXODWHWKH
EXWWRQVGXULQJWKHRSHUDWLRQRQFH
LWKDVVWDUWHG
,WZLOOVWRSDXWRPDWLFDOO\DIWHUWKH
PLQPDVVDJHEHWZHHQWKHWKRUDFLF
DQGOXPEDUDUHDV
Temperature control
ⴘ3UHVVWKHSRZHUEXWWRQ
Â&KHFNRXWWKHFRQQHFWLQJFRQGLWLRQV
RIWKHFRQWUROOHU
Â3UHVVWKHSRZHUEXWWRQRQFH2Q
3UHVVLWRQFHDJDLQ2II
ⴚ&RQWUROWHPSHUDWXUHZLWKEXWWRQ
0RGHUDWHWHPSHUDWXUHaⳄ
·5DQJHRIWHPSHUDWXUHVHWWLQJIRU
LQWHUQDOSURMHFWRUaⳄ
7HPSHUDWXUHRIFHUYLFDOYHUWHEUDH
SURMHFWRULVIL[HGDWÛ&
Â7HPSHUDWXUHVHWWLQJXQLW
aⳄ7HPSHUDWXUHVHWWLQJSHUⳄ
0RYLQJ
SDWK
Auto ྜ0RGH
0DVVDJHIXQFWLRQEHWZHHQ
WKHWKRUDFLFYHUWHEUDH

 
N4
Manual Mode Power supply
Temperature control
ⴚControl temperature with +/- button.
(Moderate temperature: 55~60Ⳅ)
· Range of temperature setting for
internal projector: 40~70Ⳅ
(Temperature of cervical vertebrae
SURMHFWRULVIL[HGDWÛ&
· Temperature setting unit
40~70Ⳅ: Temperature setting per 1Ⳅ
Manual Mode
ⴙUse the product after placing the
internal projector at the desired
position with manual button
ŸźGXULQJWKHPDQXDOPRGH
The internal projector moves while
ŸźLVEHLQJSUHVVHG
Ÿ0RYHVWKHLQWHUQDOprojector
toward the cervical region.
Âź0RYHVWKHLQWHUQDOprojector
toward lumbar region.
ⴘPress the power button.
· Check out the connecting conditions
of the controller.
· Press the power button once : On
Press it once again : Off
Moving path
How to Use Product
How to Use Controller
- How to Use External Projector
ⴘConnect the external projector into the connection part
on the right side of the main device and press the projector
button.
· Check the connection of the projector.
· Press the projector button once: ON
/ Press the projector button one more time: OFF
Operations
Temperature control
Applied to the specific area
Caution
ⴙControl temperature with +/- button.
(Moderate temperature: 55~60Ⳅ)
·The projector is not turned on when
the actual temperature is higher than
the setting temperature, which is not
meant to be any failure.
· Temperature setting unit
40~70Ⳅ: Temperature setting per 1Ⳅ
· Apply to the desired area.
· Put the projector cover on before applying it.
* The method of using the abdominal heating pad is the same as that of the
external heating projector.
· Ensure the projector to be covered by the projector cover
while the external projector is being used.
· Be aware that any direct contact from the projector to the
skin during the high temperature setting might cause burns.
Connector bay
External projector

 
N4
How to Use Controller
- How to Use Low Frequency Pad
How to Use Product
Connection
ⴙWear the abdominal band after
fixing the low frequency pad
accurately.
Low frequency pads can be used for the users with waist size of 26-42 inches.
(With the extension band, it can be used up to the waist size of 47 inches.
Please inquire if it is used for more than 47 inches.)
ⴘIf there is no gel at home, place the
wet low frequency pad towel or
a piece of 100% cotton towel or
cloth on abdomen and wear the
low frequency pad.
· When you wet a towel or a cloth with
water, please squeeze out completely
from flowing water.
Towel for the low frequency pad
Surface to contact the abdomen
The low frequency pad is a device
to improve pain or amyotrophia
percutaneously by applying weak
current to the human body.
What is the low frequency pad?
Various wearing methods You may wear it around any area other than the abdomen.
Power supply
Intensity control
③Press the low frequency button to
turn on the power supply for the
low frequency pad. (Initial setting
is set to ‘Weak 1’.)
· Check out the connecting conditions
of the low frequency pad.
· Press the low frequency button
once: On
Press it once again: Off
ⴛControl the intensity of low
frequency with the intensity button.
(Refer to the following.)
Weak 1:
Green lighting
Weak 2:
Green blinking
Strong 1:
Red lighting
Strong 2:
Red blinking
Middle 1:
Yellow lighting
Middle 2:
Yellow blinking
The low frequency pad automatically stops after operations for
about 40 minutes.

Basic use
Adjust the length of the sub mat and fix the auxiliary support bar
ⴚAfter pulling out the safety pin loop,
open the auxiliary support bar
completely toward the outer side.
Release the safety pin to fix the
auxiliary support bar in place.
 
Before use, make sure the safety pin
is fixed in place properly.
Failure to observe this precaution poses
risks of personal injury and product
damage.
N4
Caution
How to Use Product
Caution
Ensure using the projector cover while
applying the external projector.
Be aware of burns if the product is applied
to a part in the human body for a long time.
ⴘLie down with your head toward the MAIN
MAT and your legs toward the SUB MAT.
ⴙIn the automatic mode, you can massage
your arms or any other desired area using
the external projector.
ⴚDo not lie down in the opposite direction.
Normal direction
You can adjust it to 5 different lengths.
ⴘPull down the lever
attached to the bottom
frame.
ⴙWhile pulling down the
lever, pull the auxiliary
frame and adjust it
according to your height.
How to use while sitting
ⴘApply massage with the external projector
(or Abdomen heating pad) after operating
the product in the same way as the basic
use.
ⴙ
Use the product after controlling temperature
for the sub mat after stopping operations
of the main assembly.
Simultaneous use for 2 users
ⴘ Two users can use the product simultaneously
with one person on the product and another
person with the external projector (or Abdomen
heating pad) while sitting.
Caution
Ensure using the projector cover while
applying the external projector.
Be aware of burns if the product is applied to
a part in the human body for a long time.
How to apply to the abdominal area
ⴘLie your face down to the main mat and
legs to the sub mat.
ⴙPress the button with the controller to
move the internal projector to the
abdominal area.
Make sure to lie your face down after
the internal projector is positioned at the
abdominal area.
Do not apply the product to the chest part
but only to the abdominal part manually
during massage to the abdominal area.
Otherwise, it might cause damage to the
human body.
Caution
How to Use Product


N4
N4
How to Set Temperature
for Auxiliary heating part
Temperature setter
for auxiliary heating part
Auxiliary heating part
LED display lamp
During operation: LED on
During Error: LED off
Auxiliary heating part
How to Set Temperature for the Auxiliary heating part
The auxiliary heating part operates when the internal
projector is turned on. So, turn off the main power and
turn the auxiliary heating part dial clockwise to set the
temperature (30~65Ⳅ).
How to Store and Clean Product after Use
Check Indicator Window of Controller
How to Take Emergency Actions during Use
Self-check Items
Before any A/S Request
Product Specifications
Memo
Product Warranty
40
41
42
43
44
45
46
47
Product Storage and Care