Nuwave Infinity 28202 User manual

Button Function Use

Turns the Innity™Blender on and off.

Turn the red main Base Power Switch ON. Switch is located on the right side of Blender Base.

Press Power button once to turn your Innity™ Blender on. Press the Power button again and

press the red main Base Power Switch OFF to turn your Innity Blender™off.

Start/Pause Starts and pauses the cooking process,

and allows you to clear any selections.

Turn the dial to choose your appropriate blending function. Press Start/Pause to start

blending. Press Start/Pause again to stop blending. Note: Do not ll Jar above ¾ capacity.

For best results, do not ll more than 1.5 liters (51  oz) of liquid. Refer to “Instructions” in

the owner’s manual.

Time

Set your time. Press the up and down

arrows to increase or decrease the time on

the display.

Times are displayed in minutes and seconds. Adjustments can be made on all settings. Note:

When blending for a long period of time, liquids may become hot and steam may escape from

the Plunger Cap.

Number

Settings

Use the numbered settings. Default time is

3 minutes

For standard blending you can select from one of the numbered speed settings between 1 and

10. Adjust to desired time, then press Start/Pause to begin blending. Note: The lowest setting

is #1 (5,000 RPM). The highest setting is #10 (17,000 RPM).

Icons

Icon settings are for specialized blending

tasks. Each icon setting has default time

and RPM built in.

Turn the dial to desired icon setting and press Start/Pause to begin blending. Note: Always

start with cold liquids when blending. DO NOT add hot liquids to the Innity™Blender. Hold the

Up and Down buttons to move percentage points faster.

Pulse

The Innity™ Blender offers two Pulse

functions where the power settings are fully

adjustable.

Press Pulse 1 for short bursts of blending at low power (25% Power).Press Pulse 2for short

bursts of blending at high power (100% Power).

Cleaning For quick cleaning with soap and water.

Add water and 1-2 drops of liquid dish soap to your Jar, place on the Base, and close the

Lid. Turn the dial to Clean. 00:15 will be shown on the LED display. Adjust the time if desired,

and then press Start/Pause. Once nished, remove the Jar, rinse thoroughly, and dry before

using. Note: For detailed instructions on cleaning refer to “Cleaning & Maintenance.”

Quick Start Guide

Getting Started Refer to the Owner’ s Manual for more details

Model No: 28202

Model No: 20902 • Item No: BQ20902 • Rev. 2-OG • 12-16-21

Troubleshooting Guide

The Innity™ Blender was engineered with an automatic shut-off feature to prevent overheating during use. If the Innity™Blender shuts off to

cool itself down, an odor may be detected. Unplug the Innity™ Blender and wait for it to completely cool down. To prevent overheating, do not

process at speeds not recommended.

The Innity™ Blender is not turning on or working.

1. Plug may not be in the outlet. Plug in the Innity™Blender into

an appropriate power source.

2. The Red Power Switch on right side of Base may not be on.

Check to see if the Power Switch is on.

The Innity™ Blender does not work when plugged in and

Power button and Power Switch are both ON.

Make sure the unit is plugged correctly, try another wall power

outlet. If the problem persists, contact customer service.

The Innity™ Blender is not running at a high enough speed

for the recipe.

1. The Dial is not on the correct setting. Turn the Dial to proper

setting based on the recipe.

2. The Jar is overloaded. Reduce the amount of your

ingredients.

The Innity™ Blender becoming clogged and not operating

efficiently.

1. Certain ingredients can cause clogging. When using the

Plunger Lid, remove the Plunger Cap from the Lid and insert

the Plunger through hole. Press the ingredients down and

around until mixture loosens around the bottom of the Jar.

2. The ingredient amounts higher than specified are being used.

Do not fill the Jar above ¾ capacity (1.5 liters, 51 fl oz).

3. Large pieces of ice are not mixing properly. Use smaller pieces

of ice.

The blended mixture has lumps or the texture is not even.

Air pocket has formed (cavitation) and mixture is too cold or has

solidified in areas, and the blades are spinning in cavity. Increase

the temperature by reducing ice in the recipe.

Noises or motions unusual for the normal operation of the Innity™

Blender are detected.

1. The Blade assembly may be loose, missing a part, or possibly

damaged. Turn the Innity™Blender OFF and unplug immediately.

DO NOT disassemble the Blade assembly. Call Customer Service:

1-877-689-2838 or email [email protected].

2. Foreign objects from ingredients may have been put into the Jar and

are making unusual sounds. Prior to adding your ingredients to the

Jar and blending, clean fruits/other ingredients and remove all debris

or any objects.

Error Message: Solution(s)

Er1

The NTC Temperature Sensor has short circuited.

Contact NuWave Customer Service 1-877-689-2838

or help@nuwavenow.com.

Er2

The NTC Temperature Sensor is open. Contact

NuWave Customer Service 1-877-689-2838

or help@nuwavenow.com.

Er3

The NTC Sensor has overheated. Turn the Infinity™

Blender off and allow it to cool. If the Infinity™

Blender is not working after it cools down, Contact

NuWave Customer Service 1-877-689-2838 or

help@nuwavenow.com.

INFINITY BLENDER

Clean Soup Nuts Sorbet Smoothie Ice

Default Min : Sec