Nyne Performer Instruction manual

1
2
Nyne Performer
23.sec
11
23.sec
Charge the speaker until all four charging indicators
light up, indicating that the battery is fully charged.
Tips:
1 To save power, when the speaker is not in use,
always turn the power switch to the O position.
2 You can press PUSH to turn on the charging
indicators and hold the button to turn off. When
only the red indicator is on, it indicates that the
battery is low and needs to be recharged.
Make sure the power switch is in Iposition,
then hold to switch on.
To switch to standby mode, hold again.
To power off completely, turn the power
switch to the Oposition.
Performer
Quick User Guide
PA Speaker
nyne.com
EN
EN
1 Press to select the Bluetooth sound source.
2 Enable Bluetooth on your device to be paired with the speaker.
3 Select ‘Nyne Performer’ from the available devices (if necessary,
enter the password such as ‘0000’ or ‘1234’) to start pairing and
connection with the speaker.
+After successful pairing and connection, the speaker beeps.
4 Play music on your device paired and connected with the
speaker.
During music play:
• Turn the volume knob to adjust volume.
• Press to pause or resume music play.
• Press to skip to the previous/next song.
• Hold to fast forward or reverse.
Tips: This speaker supports automatic connection with a
previously paired device after power-off and power-on again.
To pair with a new Bluetooth device or connect a previously
paired device, rst hold to disconnect the current Bluetooth
device, and then repeat the above steps 2 to 3.
1 To get better reception, fully pull out the draw bar to
work as the FM antenna.
2 Press to select the FM radio sound source.
3 a. Press repeatedly to tune to a station step
by step.
b. Hold to tune to a station automatically.
To program FM radio stations:
1 a. Hold to start search and program available
stations automatically.
b. Tune to a station with , then hold a
numeric key (1 to 5) to assign a program number to
it. Repeat the steps to add more stations into your
program list.
2 Press a numeric key (1 to 5) to select the
corresponding station in your program list.
1 Press to select the USB sound source.
2 Connect a USB stick containing playable
audio les to the socket.
+The speaker reads audio les and
then plays them automatically.
During music play:
• Turn the volume knob to adjust volume.
• Press to pause or resume music play.
• Press to skip to the previous/next song.
• You can also use the numeric key (1
to 5) to select a le directly. To enter a
number with more than one digit, press the
corresponding numeric keys consecutively.
• Hold to fast forward or reverse.
• Press repeatedly to select a
repeat/shufe play mode.

AUX
1 Connect an auxiliary MP3 device to the
speaker through a 3.5mm audio cable.
2 Play and control music on the MP3 device,
and use the volume knob on the speaker
to adjust volume if necessary.
Tip: In AUX mode, you can press to
pause or resume music play.
1 Connect your guitar to the socket.
2 Press to select the guitar sound source.
+The green guitar indicator lights up.
3 Play guitar through the speaker.
During play:
Turn the knob to adjust the guitar
volume.
1 Connect a microphone to the or
socket.
2 Sing along through the microphone with
the music played through Bluetooth, USB,
AUX or the connected guitar (use the
socket if a guitar is connected).
During play:
Turn the knob to adjust the microphone
volume.
All registered and unregistered trademarks are
property of their respective owners.
Nyne Multimedia Inc.
All rights reserved.
QUG-Performer-07-08-2016-V1.0
Charge your mobile device through the
5V 1A USB charging socket.
Hold and then release repeatedly
to select one of the 8 available matrix
display modes.
Tips: To turn off the matrix display,
hold and then release repeatedly
until the matrix display disappears.