OBaby ZeZu Multi Tandem User manual

ZeZu Multi Tandem
Instructions
IMPORTANT
PLEASE READ THESE
INSTRUCTIONS
CAREFULLY BEFORE
USING THIS PRODUCT
KEEP FOR FUTURE
REFERENCE

Fitting and Removing the Adaptor
When the ZeZu Multi is used as a tandem, an adaptor needs to be tted to the chassis
before the seat unit or car seat.
Lower each adaptor on to the seat stems on either side of the chassis until they click into
place (g.52). Ensure the adaptor release button is facing outwards and the seat stem on
the adaptor is towards the front of the chassis.
To remove the adaptor press the release button on each of the adaptors and lift up away
from the chassis (g.53).
g. 51 g. 52 g. 53
“Click”
Fitting the Mud Guards
To t the mud guards, rst remove the rear wheel (see page 5 in the ZeZu manual).
Then slide the mud guard on to the bracket on the rear wheel bar (g.48 & 49).
Replace the wheel (see page 5 in the ZeZu manual).
g. 48 g. 49 g. 50
1.Press
2.Lift
ZeZu Multi Tandem Safety Warnings
Thank you for choosing Obaby. To ensure that your ZeZu Multi Tandem Kit is used in
accordance with these instructions, please read them fully.
The pramette and tandem kit conforms to EN 1888:2012 and is guaranteed for 24 months
from the date of purchase against manufacturing defects. If, however you have any
problems, please contact your Obaby retailer from whom you purchased your product,
who will take appropriate action.
Your child’s safety may be affected if you do not follow these
instructions.
WARNING: Do not place a child in the rear seat without a child being
in the main seat unit.
WARNING: Never leave your child unattended.
WARNING: A child’s safety is your responsibility.
WARNING: Ensure that all locking devices are engaged before use.
WARNING: To avoid injury ensure that your child is kept away when
unfolding and folding this product.
WARNING: Do not let your child play with this product.
WARNING: This seat unit is not suitable for children under 6 months.
WARNING: Children should be harnessed in at all times.
WARNING: Check that the rear seat or ride on board, adaptors,
mudguards and handle (where necessary) are correctly engaged
before use.
• The rear seat is intended to carry one child from 6 months and up to a
maximum weight of 15kg
• The ride on board is intended to carry one child from 6 months and up
to a maximum weight of 20kg
ROUTINE CARE & MAINTENANCE
Refer to your ZeZu pramette instructions
Due to constant updating and improvements, some components may occasionally differ slightly from the images
shown in these instructions. We reserve the rights to change the specications of any products without prior notice.
If you need any assistance please contact your Obaby retailer from whom you purchased your product, who will take
appropriate action.
Ride on handle
Ride on
Mud guards
Infant seat
Adaptors
23
www.obaby.co.uk www.obaby.co.uk

Located towards the rear wheels, at the back of the shopping basket are 2 receiver stems
(g.60). The stems need to be uncovered before the rear seat or ride on can be used.
To uncover the stems, lift the cap (g.61).
To recover the stems, when the tandem is not in use, simply push the cap until it clicks
into place (g.62).
“Click”
Preparing to use the Tandem
g. 60 g. 61 g. 62
Using the Seat with the Adaptor
Using the Car Seat with the Adaptor
g. 54
g. 57
g. 55
g. 58
g. 56
g. 59
“Click”
“Click”
1.Press
1.Press
2.Lift
2.Lift
The seat unit can face either forwards or backwards.
To put the seat unit onto the adaptor, line up the seat coupler with the seat stem on the
adaptor on each side of the chassis and lower onto the adaptor (g. 54 & 55), ensure it
clicks into place on both sides.
To remove the seat from the adaptor, press both release buttons on each side of the seat
unit (g.56) and lift the seat up, away from the adaptor.
To put the car seat onto the adaptor, line up the seat coupler with the seat stem on the
adaptor on each side of the chassis and lower onto the adaptor (g. 57 & 58), ensure it
clicks into place on both sides.
To remove the car seat from the adaptor, press both release buttons on each side of the
car seat (g.59) and lift the car seat up, away from the adaptor.
45
www.obaby.co.uk www.obaby.co.uk

Before tting the ride on board, ensure that the adaptors and either the seat unit or car
seat has a child in and are tted on to the chassis (see page 3 & 4), to avoid tipping.
Line up the ride on board stems with the receivers on the chassis (g.69) and push the
ride on board down, until it clicks into place (g.60 & 71).
To remove the ride on board, press the buttons on the inside of the stem receivers, on
both sides of the chassis (g. 72 & 73), and lift the ride on board up, away from the
chassis (g.74).
g. 72 g. 73 g. 74
“Click”
Fitting and Removing the Ride On Board
g. 69 g. 70 g. 71
Lift
Press
Fitting and Removing the Rear Seat
Before tting the rear seat, ensure that the adaptors and either the seat unit or car seat
has a child in and are tted on to the chassis (see page 3 & 4), to avoid tipping.
Line up the rear seat stems with the receivers on the chassis (g.63) and push the rear
seat down, until it clicks into place (g.64, 65 & 66).
To remove the rear seat, press the buttons on the inside of the seat stem receivers, on
both sides of the chassis (g. 67 & 68), and lift the rear seat up, away from the chassis.
g. 66 g. 67 g. 68
“Click”
g. 63 g. 64 g. 65
Press
67
www.obaby.co.uk www.obaby.co.uk

Fitting and Removing the Handle
To t the rear handle, line up the receivers on the handle with the pegs on either side of
the chassis and push the clips around the chassis, until they click into place (g.75 & 76).
To remove the handle, unclip the clips from either side and lift away from the chassis
(g.77).
g. 75 g. 76 g. 77
Press
Press
“Click”
8
www.obaby.co.uk www.obaby.co.uk