OEA UPD-K01 User manual

OWNER’S MANUAL
ULTRASONIC WARNING SYSTEM
913-599-9040 |OEAttachments.com

Table of Contents
Caution/Warning for Safety 4
Components 6
Installation 7
How to Connect Products 8
Operation Principle 9
How to Use Indicator 10
Specifications 11
Warranty 12
MODEL:
SERIAL NUMBER:
(Located on data plate attached to the unit frame)
DATE PURCHASED:
OWNER’S MANUAL
ULTRASONIC WARNING SYSTEM
Model. UPD-K01

Owner’s Manual
4 OEA SafeGuard
CAUTION/WARNING FOR SAFETY
CAUTION!
Failure to observe the precautions in this manual may result in damage to the product or
your property.
Use only DC 12/24V.
For vehicles with DC
36/48V, be sure to
connect SMPS module
to use DC 12/24V.
Otherwise, this may
cause issues.
Do not touch the
connector or wiring
with wet hands.
This may cause
electric shock or fire.
Do not intentionally
immerse the product
in water or wash it
in running water.
Otherwise, it may
cause malfunction.
Do not place the
product near
flammable materials,
stoves, candles, or
fire. This may cause
fire and product
deformation.
Do not place heavy
objects on the product
or wiring. It may cause
electric shock or fire.
If the product smells,
smokes, or makes
abnormal noises, turn
o the power and
contact the customer
service center
immediately.

OEAttachments.com | 913-599-9040 5
Owner’s Manual
CAUTION FOR WIRING CONNECTION
Any accidents that result from not following the instructions in this manual are the user’s
responsibility.
Do not remove the
cap when the cable
is not in use.
If a connector or a
wiring gets wet, wipe
it with a dry towel.
Otherwise, it may
cause electric shock
or fire.
Tighten the cable
terminals to properly
connect. Malfunctions
may be caused by
liquid matters if
disregarding it.
Do not disassemble or
modify this product.
This may cause trouble,
and After- Sale Service
will not be available.

Owner’s Manual
6 OEA SafeGuard
COMPONENTS
Open Wire Adapter Cable
Optional
Horn Speaker
[Set 1] Sensor Cable
Optional
[Set 2] Sensor Cable
Cable Harness
User Manual
Indicator
Ultrasonic Sensors (2)
*Screws excluded in the product component.
The appearance of the product may be slightly dierent from the actual product received.
Product Diameter of Screw Hole Diameter of Screw Quantity Required
Ultrasonic Sensor Ø 0.25in Ø 0.24in 4EA (2EA/sensor)
Indicator Ø 0.28in Ø 0.24in 4EA
Horn Speaker (optional) Ø 0.46in Ø 0.39in 2EA
ULTRASONIC WARNING SYSTEM

OEAttachments.com | 913-599-9040 7
Owner’s Manual
• Indicator: Installed near the
driver seat.
• Sensor: Installed outside (in rear,
front or side) of the vehicle.
INSTALLATION

Owner’s Manual
8 OEA SafeGuard
HOW TO CONNECT PRODUCTS
CAUTION!
Please make sure to install the products AFTER cutting the power supply.
Do not remove the cap when the cable is not in use.
Tighten the cable terminals to properly connect.
Disregarding this may cause a malfunction by liquid matters.
5
How To Connect Products
Cap Do not remove the cap when the cable is unused.
Tighten the connectors to properly connect.
It may cause a malfunction by liquid matters if disregarding it.
Caution! Please make sure to install the products after cutting the power supply.
Indicator
Fuse
▶ Yellow : Rear Det.
▶ Red : (+) Power
▶ Black : (-) Power
[Set1] Sensor 1
[Set1] Sensor 2
Horn Speaker
Optional
[Set2] Sensor 1
Optional
[Set2] Sensor 2
Optional
HOW TO CONNECT PRODUCTS

OEAttachments.com | 913-599-9040 9
Owner’s Manual
OPERATION PRINCIPLE
3ft
7ft
10ft
3ft
7ft
10ft
3ft
7ft
10ft
Detect obstacles within 3ft
Indicator
“Beep Beep Beep Beep”
Fast Tempo
Horn Speaker (Optional)
“Watch out. Danger.”
Voice Alarm
Detect obstacles within 7ft
Indicator
“Beep-- Beep-- Beep--”
Medium Tempo
Horn Speaker (Optional)
“Watch out. Danger.”
Voice Alarm
Detect obstacles within 10ft
Indicator
“Beep---- Beep----”
Slow Tempo
Horn Speaker (Optional)
“Watch out. Danger.”
Voice Alarm

Owner’s Manual
10 OEA SafeGuard
HOW TO USE INDICATOR
• Push the Power Button after starting the vehicle. The green
lights come on from the LED lamp and the button.
• Mode Button OFF (Light OFF): Sensors activated all the time
• Mode Button ON (Light ON): Sensors activated only when the
reverse gear operates
• Change the volume level using Volume Buttons. (The volume
of the indicator and the horn speaker are changed together.)
7
How To Use Indicator
· Push the power button after starting the vehicle.
The green lights come on from the LED lamp and the button.
· Mode Button OFF (Light OFF): Sensors activated all the time
· Mode Button ON (Light ON): Sensors activated only when the
reverse gear operates
· Change the volume level using Volume Button. (The volume of
the indicator and the horn speaker is changed at once.)
Power Button
Mode Button Volume Button
LED Lamp Speaker Hole