OEM Tools 27090 Service manual

WARNING
The following safety information is provided as a guideline to help you operate your Brake Anchor Pin Press under the
safest possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe
handling instructions are not known or not followed. The following safety instructions are to provide the user with the
information necessary for safe use and operation. Please read and retain these instructions for the continued safe use
of your Brake Anchor Pin Press. Failure to follow instructions listed below may result in serious injury. In addition, make
sure that anyone who uses the equipment understands and follows these safety instructions as well.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this
product before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible
for issues arising from modification. We strongly recommend that this product is not modified and/or used for any application
other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the
product until you have first contacted customer service to determine if it can or should be performed on the product.
WARNING:Pursuant to California Proposition 65, this product contains chemicals known to the state of California to
cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Operating Instructions and Parts Manual 27090
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself
and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in
personal injury and/or damage to product or property. Please retain instructions for future reference.
1
9/21
2021 OEMTOOLS®
BRAKE ANCHOR PIN PRESS
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
UNPACKING
After unpacking the unit, inspect carefully for any damage
that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed,
a shipping damage claim must be filed with the carrier.
DO NOT use the OEMTOOLS®27090 Brake Anchor
Pin Press Tool if broken, bent, cracked, or damaged
parts (including labels) are noted. Any Brake Anchor Pin
Press Tool that appears damaged in any way, operates
abnormally or is missing parts should be removed from
service immediately. If you suspect that the Brake Anchor
Pin Press Tool was subjected to a shock load (a load that
was dropped suddenly, unexpectedly, etc.) immediately
discontinue use until it has been checked by a factory
authorized service center.

2
Operating Instructions and Parts Manual 27090
9/21
2021 OEMTOOLS®
BRAKE ANCHOR PIN PRESS
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn
the product’s applications and limitations, as well
as potential hazards specific to it. The use of this
product is simple and straightforward if you follow the
instructions. When operating this product, use common
sense and only use this product for its intended
purpose.
2. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS®for a replacement.
3. Maintain this product with care. Keep it dry and clean –
and free from brake fluid, oil, and grease (if applicable).
4. Check for damage. Check your product regularly. If
part of the product is damaged, it should be carefully
inspected to make sure that it can perform its intended
function correctly. If in doubt, the part should be
repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
5. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the product’s operation.
6. DO NOT use a damaged product. Tag damaged
products “DO NOT USE” until repaired. If damaged,
have the product serviced before using. Many
accidents are caused by poorly maintained products.
7. Service must be performed only by qualified repair
personnel. Service or maintenance performed by
unqualified personnel could create a risk of injury.
8. When servicing a product, use only identical
replacement parts. Use of unauthorized parts or failure
to follow maintenance instructions could create a risk
of injury.
9. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one product may become hazardous when
used on another product.
10. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
11. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
12. Keep children away from the work area. Never
let a child handle this product without strict adult
supervision.
13. Store this product out of the reach of children and
untrained persons. This product may be dangerous in
the hands of untrained users.
14. DO NOT operate this product if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
15. Use safety equipment. Eye protection should be worn
at all times when operating this product. Use ANSI
approved safety glasses. Everyday eyeglasses are NOT
safety glasses. Dust mask, non-skid safety shoes, hard
hat or hearing protection should be used in appropriate
conditions.
16. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this product. Keep all apparel
clear of the product.
17. DO NOT overreach. Keep proper footing and balance
at all times when operating this product.
18. Keep away from flammables. DO NOT attempt to
operate this product near flammable materials or
combustibles. Failure to comply may cause serious
injury or death.
19. Avoid accidental fire and/or explosion. DO NOT smoke
near engine fuel and battery components.
20. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part. Always
refer to specific instructions and technical information
supplied by vehicle manufacturer.
21. The manufacturer declines any and all responsibility
for property damage or injury if said damage is the
result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
22. The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product, but must be
supplied by the operator.
PRODUCT DESCRIPTION
The OEMTOOLS®27090 Brake Anchor Pin Press
compact design allows the user to service brake anchor
pins and bushings without the removal of the hub and the
dust shield. Includes: (1) C-Frame, (1) Forcing Screw,
(1) Centering Bushing, (1) Bushing Remover and
(2) O-Rings.

3
Operating Instructions and Parts Manual 27090
9/21
2021 OEMTOOLS®
BRAKE ANCHOR PIN PRESS
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
The following safety information is provided as a guideline
to help you operate your Brake Anchor Pin Press Tool
under the safest possible conditions. Any tool or piece
of equipment can be potentially dangerous to use when
safety or safe handling instructions are not known or
not followed. The following safety instructions are to
provide the user with the information necessary for
safe use and operation. Please read and retain these
instructions for the continued safe use of your tool.
Failure to follow instructions listed below may result in
serious injury. In addition, make certain that anyone who
uses the equipment understands and follows these safety
instructions as well.
WARNING:
1. Always keep the forcing screw well lubricated.
2. DO NOT exceed the maximum recommended torque
for each forcing screw.
NOTE:Exceeding these torque values may shorten the life
of the forcing screws. The forcing screws are consumable
items and are NOT covered under warranty.
OPERATION INSTRUCTIONS
A. ANCHOR PIN REMOVAL
1. Install the Centering Bushing onto the back side of the
anchor pin shoulder.
2. Position the C-Frame over the anchor pin (and
Centering Bushing) and tighten the Forcing Screw by
hand until the anvil contacts the front side of the anchor
pin.
3. Apply force with a 1/2" impact wrench until the anchor
pin has been removed. (Note: Centering Bushing may
push out the C-Frame, this is normal.)
B. BUSHING REMOVAL
NOTE:In the event you are servicing a stamped spider, a
punch and chisel may be required to remove the bushing.
1. Install the magnetized bushing adapter onto the anvil.
2. Position the C-Frame over the bushing in the spider so
the “step” in the bushing adapter seats inside of the
bushing.
3. Apply force with a 1/2" impact wrench until the bushing
has been removed.
Figure Description Qty.
A C-Frame 1
B Extension Bar 1
C Forcing Screw 1
D Centering Bushing 1
E Bushing Remover 1
F O-Ring #2-012 1
G O-Ring #021 1
PRODUCT LAYOUT PARTS LIST
A
B
C
D
E
G
F

4
Operating Instructions and Parts Manual 27090
9/21
2021 OEMTOOLS®
BRAKE ANCHOR PIN PRESS
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®LIFETIME LIMITED WARRANTY
For as long as you own this OEMTOOLS®product, if you find any defect in material or workmanship, through normal
usage, return it to the place of purchase or to OEMTOOLS®for repair or replacement at our discretion. In order to
obtain this service, send your tool and proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our
inspection verifies the defect, we will repair or replace the product, or we may elect to refund the purchase price if we
cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you
must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will
not provide any warranty for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse,
accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS®reserves the right to make any changes in construction or design at any
time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and warrants
to the original purchaser that this product is free from defects in materials and workmanship. This warranty does not
apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our
facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.
CONTACT US