OEM Tools 24453 Service manual

UNPACKING
After unpacking unit, inspect carefully
for any damage that may have occurred
during transit. Check for loose, missing,
or damaged parts. If any damage is
observed, a shipping damage claim must
be filed with carrier. Do not use the OBD2
Memory Saver if broken, bent, cracked
or damaged parts (including labels) are
noted. Any part that appears damaged
in any way, operates abnormally or is
missing parts should be removed from
service immediately. If you suspect that
the OBD2 Memory Saver was subjected
to shock load (a load that was dropped
suddenly, unexpectedly, etc.) immediately
discontinue use until it has been checked
by a factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect
yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions
could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
Operating Instructions and Parts Manual 24453
OBD2 MEMORY SAVER
Explanation of Safety Signal Words
CAUTION
Notes
CAUTION
WARNING
The following safety information is provided as guidelines to help you operate your OBD2 Memory Saver under the
safest possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe
handling instructions are not known or not followed. The following safety instructions are to provide the user with the
information necessary for safe use and operation. Please read and retain these instructions for the continued safe use
of your service system. Failure to follow instructions listed below may result in serious injury. In addition, make certain
that anyone that uses the equipment understands and follows these safety instructions as well.
WARNING: Pursuant to California Proposition 65, this product contains chemicals known to the state of California to
cause cancer and birth defects or other reproductive harm. Wash hands after handling.
WARNING
: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
:
Used without the safety alert symbol indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
: Provide clarity and helpful information.

2
Operating Instructions and Parts Manual 24453
OBD2 MEMORY SAVER
Thank you very much for choosing an OEMTOOLS
Product!
For future reference, please complete the owner’s
record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is
important that you read the entire manual to become
familiar with this product before you begin using it.
This machine is designed for certain applications only.
OEMTOOLS cannot be responsible for issues aris-
ing from modification. We strongly recommend this
machine is not modified and/or used for any ap-
plication other than that for which it was designed.
If you have any questions relative to a particular
application, DO NOT use the machine until you have
first contacted OEMTOOLS to determine if it can or
should be performed on the product.
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn
the tool’s applications and limitations, as well as,
potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
3. Keep children away. All children should be kept
away from the work area. Never let a child handle
a tool without strict adult supervision.
4. Do not operate this tool if under the influence
of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is
any doubt, do not attempt to operate.
5. Use safety equipment. Eye protection should
be worn at all times when operating this tool.
Use ANSI approved safety glasses. Everyday
eyeglasses are NOT safety glasses. Dust mask,
non-skid safety shoes, hard hat or hearing
protection should be used in appropriate
conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-
ties, rings, bracelets or other jewelry may present a
potential hazard when operating this tool. Keep all
apparel clear of the tool.
7. Don’t overreach. Keep proper footing and balance
at all times when operating this tool.
8. Check for damage. Check your tool regularly. If
part of the tool is damaged it should be carefully
inspected to make sure that it can perform its
intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a qualified
technician. Consult your dealer for advice.
9. Keep away from flammables. Do not attempt
to operate this tool near flammable materials
or combustibles. Failure to comply may cause
serious injury or death.
10. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in the
hands of untrained users.
• Maintain tools with care.
• Keep tools dry and clean.
•Do not use a damaged tool. Tag damaged tools “Do
not use” until repaired.
•If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
•Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool may become hazardous when
used on another tool.
•Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
•When servicing a tool, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
•Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. Do not use this
product in a damp or wet location.
•Maintain labels and nameplates on this product.
These carry important information. If unreadable or
missing, contact OEMTOOLS for a replacement.
•Before use, read and understand all warnings, safety
precautions, and instructions as outlined in the
vehicle manufacturer’s service manual. It is beyond
the scope of this manual to properly describe the
correct procedure and test data for each vehicle.
•Always perform vehicle service in a properly ventilated
area. Never run an engine without proper ventilation
for its exhaust. Stop work and take necessary steps
to improve ventilation in the work area if you develop
momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.

3
Operating Instructions and Parts Manual 24453
OBD2 MEMORY SAVER
•Engine parts that are in motion and unexpected
movement of a vehicle can injure or kill. When working
near moving engine parts, wear snug fit clothing and
keep hands and fingers away from moving parts.
Keep hoses and tools clear of moving parts. Always
stay clear of moving engine parts. Hoses and tools
can be thrown through the air if not kept clear of
moving engine parts. The unexpected movement of
a vehicle can injure or kill. When working on vehicles
always set the parking brake or block the wheels.
•Avoid accidental fire and/or explosion. Do not smoke
near engine fuel and battery components.
•We believe the information contained herein to be
reliable. However, general technical information is
given by us without charge and the user shall employ
such information at his own discretion and risk. We
assume no responsibility for results or damages
incurred from the use of such information in whole or
in part.
•The manufacturer declines any and all responsibility
for damage to vehicles or components if said damage
is the result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions and
situations that may occur. The operator must understand
that common sense and caution are factors which
cannot be built into this product, but must be supplied by
the operator.
PURPOSE
The only OBD-II Memory Saver designed for use with
lithium portable power units with fuse and back charge
protection. The OBD2 Memory Saver works with
OEMTOOLS®multi-use lithium portable power products
(24370, 24379 and 24454) - Patent Pending. As well as,
most other lithium jump starters on the market.
INSTRUCTIONS
1. Turn off any accessories: light, radio, etc.
2. Make sure vehicle is off and remove key.
3. Connect the OBD2 Memory Saver to the vehicle’s
OBD2 port. Make sure the connector is fully
engaged.
4. Connect the OBD2 Memory Saver Plug to your
12V DC power supply’s EC5 connector. Make sure
the plug is firmly in place.
5. Disconnect the vehicles battery cables and
perform maintenance.
6. When maintenance is complete, connect vehicle
cables to the vehicle battery.
7. Immediately remove OBD2 Memory Saver from the
power source and then the OBD2 adapter from the
OBD2 vehicle port.
NOTE:
Never start the vehicle or turn on the accessories with
the OBD2 Memory Saver connected to the vehicle.
When working with a vehicle’s battery, review all of
the battery manufacturer’s and vehicle manufacturer’s
safety instructions, warnings and directions regarding
battery disconnection, removal and replacement.
The vehicle’s electrical system is receiving power from
the Memory Saver through the OBD2 port. Therefore,
the vehicle’s battery connectors are electrically live and
will still conduct electricity. They must be covered with
an insulator to prevent the connectors from touching
metal or each other and causing a short circuit.
Allowing a short circuit to occur could cause damage
to the electrical system of the vehicle.
NOTE:
Do not use an extension cable on either end of the
memory saver. Doing so could cause the vehicle’s
memory to be lost or cause the other vehicle damage.
TROUBLESHOOTING
The Memory Savor contains a 5 AMP fuse. Should
an issue occur with the Memory Saver, check the
fuse prior to calling customer service.
Do not operate the tool in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust
Do not expose the tool to heat
Do not store in locations where the temperature may
exceed 70°C
Do not modify or disassemble OEMTOOLS OBD2
Memory Saver. Only a repair technician may repair
this unit.
CAUTION
CAUTION
Always take care when using this tool
This power source is not intended for use by young
or infirm persons without supervision
Do not use as a toy
Do not allow the tool to become wet.
Do not immerse tool in water

4
Operating Instructions and Parts Manual 24453
OBD2 MEMORY SAVER
OEMTOOLS™ 90 DAY LIMITED WARRANTY
From 90 Days from the original purchase date of this product, OEMTOOLS will warranty this product. If you
find any defect in material or workmanship, through normal usage, return it to the place of purchase or to
OEMTOOLS for repair or replacement at our discretion. In order to obtain this service send your tool and proof
of purchase, transportation pre-paid, to OEMTOOLS Q.A. We will not be responsible for lost or damaged
goods during transportation, please insure your package. If
our inspection verifies the defect, we will either repair or replace the product at our election, or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS does not provide warranty for products labeled other than OEM or OEMTOOLS. OEMTOOLS will
not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited to,
abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not
cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or
replace blades, bits, files, and batteries as necessary. OEMTOOLS reserves the right to makes any changes in
construction or design at any time without any obligation in incorporating such changes to tools or equipment
previously sold.
OEMTOOLS makes every effort to assure that its products meet high quality and durability standards, and
warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, and normal wear and tear or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, and contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS. This warranty gives you specific legal rights, and you may also have other rights, which vary from state
to state.
• Consumable components such as batteries are not covered by the warranty
•This warranty is invalidated if any of the following occurs, but not limited to this list:
• Failure to follow instructions in the User’s Manual
• Accidental and or unreasonable use or misuse
• Mishandling
• Over charging or overloading
• Extended storage without recharging
• Repairs by and un-authorized person or any modification
• Normal wear or accident