Office Star Products FL642 User manual

FL642 FAUX LEATHER CHAIR
OPERATING INSTRUCTIONS
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs
are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
LIMITED WARRANTy
Ofce Star chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 5 Years on all non-moving metal parts.
• 2 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 1 Year on upholstery fabric and foam against wear and deterioration.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and
obtain return authorization. At it’s option Ofce Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return
freight on components still in warranty will be paid by Ofce Star Products.
*All warranties are limited to the original purchaser for normal Residential usage by persons weighing 200 lbs. or less. This warranty will not cover labor,
freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star
Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The
user assumes all risk of injury resulting from use of this product. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacic Time.
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and twist lever (1) down.
To lower seat height sit on chair and twist lever (1) down.
NOTE: It is normal for chair to slightly lower
under body weight.
• MID-PIVOT KNEE TILT ADJUSTMENT
To adjust tilt angle, twist lever (3) down for free float, and twist
lever (3) up to lock into any postition.
• TILT TENSION ADJUSTMENT
To adjust tilt tension, turn knob (2) counter-clockwise to increase
tension, and turn knob (2) clockwise to decrease or ease tension.
2
13

FL642 FAUX LEATHER CHAIR
ASSEMBLY INSTRUCTIONS
© Office Star Products November 2007
STEP 1
1
26
6
7
3
3
9
4
5
8L
9,10
8R
STEP 2 STEP 3
STEP 4
PART QTY
1. Base .......................1
2. Casters .....................5
3. Pneumatic Cylinder ............1
4. Bellows .....................1
5. Mechanism ..................1
6. Seat Cushion .................1
7. Back Cushion . . . . . . . . . . . . . . . . 1
8. Arms Left (8L) Right (8R). . . . . . . . 2
9. Screws .....................12
10. Caps ......................8
11. Allen Wrench (not shown) . . . . . . 1
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place. Insert Pneumatic Cylinder (3) into Base (1) and
slip Bellows (4) over Pneumatic Cylinder (3).
STEP 2 Attach Arms (8L & 8R) to Seat Cushion (6) and Back Cushion (7), using four Screws (9) for each Arm (8), FULLY TIGHTEN ALL SCREWS.
Cover each hole on Arms (8L & 8R) using eight Caps (10).
STEP 3 Attach Mechanism (5) to Seat Cushion (6) with the arrow towards the front of the chair, using four Screws (9)
TIGHTEN ALL FOUR SCREWS COMPLETELY.
STEP 4 Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.