OfficeSource PL437T HALF User manual

KLIX CAM INSTRUCTIONS
Insert the cam with the arrow
pointing towards the hole in the
edge.
Line up Cam Lock,
turn clockwise.
12
Insert the Cam Lock into Klix
Cam. Turn Klix Cam to lock.
3DETAIL x-x
ADJUST THIS SCREW FOR DOOR ALIGNMENT
AFTER ASSEMBLY THE HINGES.
BACK VIEW
HINGES INSTRUCTIONS
MODEL: PL 437T HALF
1 OF 6
Before assembly, please remove all parts from carton, verifying that you have the correct quantities, and read all the instructions.
IN THE CARTON:
ASSEMBLY INSTRUCTIONS
See Page 3 See Page 4
See Page 5 See Page 6
WITH END BASE WITH ELLIPTICAL BASE
WITH CUBED BASE WITH V-LEG/U-LEG BASE
See Page 6
WITH V-LEG/SQUARE
POST LEG BASE
WALL
®
®
OFFICE FURNITURE
MODEL NO. PL437T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 1 of 6

2 OF 6
!ATTENTION !
Place all wooden parts on a clean, smooth surface to prevent them from being scratched.
Check to be sure that you have all parts and hardware. Remove all wrapping materials, including staples and packing straps before
you start to assemble. Do not tighten all screws/bolts until all completely assembled. Keep all hardware parts out of reach of children.
If any parts are missing, broken, damaged or worn, stop use of product until repairs have been made using factory authorized parts.
Failure to follow these warnings may result in injury.
MODEL: PL 437T HALF
ASSEMBLY INSTRUCTIONS
Modesty Panel
BA Top Panel
for PL 437T HALFX2
Klix Cam
10 Pcs
Cam Lock
10 Pcs
M4 x 65
Allen-Key
1 Pc
Housing
Cap (Short)
4 Pcs
Housing
Cap (Long)
6 Pcs
Adjustable
Glide
4 Pcs
C8
Screw
#6 x 58"
24 Pcs
C1 C2 C3 C4 C5 C7
6 Hole
L-Bracket
4 Pcs
C6
END BASE x 2
C
++
Elliptical Base x 2
D
+
Klix Cam
6 Pcs
Cam Lock
6 Pcs
M4 x 65
Allen-Key
1 Pc
Housing
Cap (Long)
6 Pcs
Adjustable
Glide
4 Pcs
D7
Screw
#6 x 58"
24 Pcs
D1 D2 D3 D4 D6
6 Hole
L-Bracket
4 Pcs
D5 D8
CSK Scew
M3.5 x 20MM
16 Pcs
+
CUBED BASE x 3
E
Modesty Panel
B
+
PLT-V-LEG X 2
F
+
PLT-RET SUPPORT
X 8
H
PLTLEG-U
G
+
F1 F2 F3
#6 x 16mm P/H
Cross Recess
Screw
4 Pcs
Screw
#4 x 16mm
16Pcs
M4 x 65
Allen-Key
1 Pc
G1 G2 G3
#6 x 16mm P/H
Cross Recess
Screw
4 Pcs
Screw
#4 x 16mm
16Pcs
M4 x 65
Allen-Key
1 Pc
H1
Screw
#4 x 16mm
32Pcs
A1
Screw
#6 x 58"
48 Pcs
6 Hole
L-Bracket
6 Pcs
Flat-Bracket
2 Pcs
A2 A3
FOR
ELLIPTICAL
BASE
FOR
CUBE
BASE
FOR
V-LEG/U-LEG
BASE
FOR END
BASE
I1
Screw
#4 x 16mm
4Pcs
INCLUDED
WITH TABLE
TOP
INCLUDED
WITH CUBE
BASE
INCLUDED
WITH
V-LEG/U-LEG
BASES
INCLUDED
WITH END
BASES
INCLUDED WITH
ELLIPTICAL
BASES
A A
A
+
PLT-V-LEG
F
+
PLT-RET SUPPORT
X 2
HI
+
FOR
V-LEG/U-LEG
BASE
A
PLT Post Leg x 2
INCLUDED
WITH SQUARE
POST LEG
COMPONENTS:
HARDWARE:
Top Panel
for PL 437T HALFX2
Top Panel
for PL 437T HALFX2
Top Panel
for PL 437T HALFX2
Top Panel
for PL 437T HALFX2
E1 E2 E3
M4 x 65
Allen-Key
1 Pc
Adjustable
Glide
5 Pcs
E4 E5 E6
JCBC Screw
M6 x 40mm = 8pcs
14Washer = 8pcs
Klix Cam
18 Pcs
Housing
Cap (Short)
4 Pcs
Cam Lock
18 Pcs
E7
6 Hole
L-Bracket
4 Pcs
Screw
#6 x 58"
24 Pcs
E8 E9
0' Compo
Door Hingers
1 Pair
Screw
#3.5 x 16mm
2 Pcs
Magnet
Catches
1 Set
Screw
#3.5 x 12mm
2 Pcs
E10 E11 E12
Housing
Cap (Long)
14 Pcs
E13
®
®
OFFICE FURNITURE
MODEL NO. PL437T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 2 of 6

MODEL: PL 437T HALF
ASSEMBLY INSTRUCTIONS
3 OF 6
INSTRUCTION:ASSEMBLING TABLE WITH END PANEL BASE
C
Screw Adjustable Glide (C5) into
bottom of End Base (C).
Attach the body (B&C) to
Top Panel (A) by using
Cam Lock (C1) and Klix
Cam (C2).
4
Attach Housing Cap (A3/C3/C4) to
all Klix Cam(A2/C2) by pushing
neck thought center of cam.
C5
Attach the L-Bracket (A4/C6) to
End Base (C) and Modesty Panel
(B) as shown. Tighten Screws
(A6/C7) securely.
A
3
1
B
C
A4
C
B
C
Attach the two End Base
(C) to Modesty Panel (B) by
using Cam Lock (C1) and
Klix Cam (C2).
C6
&
A6 C7
&
BOTTOM
FACE
A
A
5
2
A
C
(A3/C3/C4)
A2
A3
Attach the Flat-Bracket (A2) to
two Top Panel (A) as shown.
Tighten Screws (A3) securely.
BOTTOM
FACE
®
®
OFFICE FURNITURE
MODEL NO. PL437T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 3 of 6

MODEL: PL 437T HALF
ASSEMBLY INSTRUCTIONS
4 OF 6
INSTRUCTION:ASSEMBLING TABLE WITH ELLIPTICAL BASE
Attach 2 Pcs Elliptical Base (D) to
Modesty Panel (B) by using Cam
Lock (D1) and Klix Cam (D2).
Attach Top Panel (A) to
Modesty Panel (B) by
using Cam Lock (D1)
and Klix Cam (D2).
A
D
D
B
Attach Elliptical Base
(D) to Top Panel (A) by
using Screw (D8).
Attach the L-Bracket (A4/D5) to
Elliptical Base (D) and Modesty
Panel (B) and Top Panel (A) as
shown. Tighten Screws (A6/C6)
securely.
A4 D5
&
A6
D6
&
BOTTOM
FACE
A
A
A
32
4
A5
A6
Attach the Flat-Bracket (A5) to two Top Panel (A)
as shown. Tighten Screws (A6) securely.
Attach metal plate to Elliptical Base (D)&(F)
with included screws.
D4
F
Screw Adjustable Glides (D4)&(F4) into
bottom of Elliptical Bases (D)&(F).
D
1
&D
F4
&
F
&&
D F
D
BD
D
D
A
CF8D8 &
BOTTOM
FACE
®
®
OFFICE FURNITURE
MODEL NO. PL437T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 4 of 6

MODEL: PL 437T HALF
ASSEMBLY INSTRUCTIONS
5 OF 6
INSTRUCTION:ASSEMBLING TABLE WITH CUBED BASE
Assemble Cube Base by attaching
Side Panels(C)&(D) to Back
Panels(E),Top rail(F) & Bottom Rail(G)
with Cam Lock (E1) and Klix Cam (E2).
Attach Cube Base Support (B) by using Cam Lock (D1) and Klix Cam (D2).
3
F
G
C
D
H
COR D
H
E10
B
E10
E9
H
CD
OR
E8
B
C
D
&
Attach Magnet Catches(E10) to Side
Panel(C)or(D) by using Screw(E11).
Attach L-Bracket(E7) to
Side Panel(C)&(D) and
Hanging Rail(B) by using
Screw(E8).
Attach Hinges(E9) to Side
Panel(C)or(D) and Door(H) by using
Screw(E9).
Attach Catches Plate(E10) to
Door(H) by using Screw(E12).
C
D
G
E
F
Screw Adjustable Glide
(E5) into bottom of End
Base (C,D).
E5
C
D
G
E
2
1
E7
B
E12
E11
4
A
Attach the Flat-Bracket
(A2) to two Top Panel (A)
as shown. Tighten Screws
(A3) securely.
A2
A3
BOTTOM
VIEW
A
E13
E6
Attach Top Panels (A) to
Cube Bases (B) with JCBC
Screws (E13) and tighten
with Allen Key (E6).
®
®
OFFICE FURNITURE
MODEL NO. PL437T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 5 of 6

6 OF 6
ASSEMBLY INSTRUCTIONS
MODEL: PL 437T HALF
Attach Screws
#4 x 16mm(E2/G1) to
PLT-V-Legs.
E1
F2 H1
Attach PLT V-Legs(E) to
Top Panel(A) by using
#6 x 16mm P/H Cross
Recess Screws(E1).
A
EG
F1
Attach PLT LEG-U(F)
to Top Panel(A) by
using #6 x 16mm P/H
Cross Recess
Screw(F1).
2
A
E
FG
F2 G1
Attach Screw
#4 x 16mm(F2/G1)
to PLT Leg-U(F).
Attach Screws
#4 x 16mm(H1/F2) to
PLT-V-Legs.
A
F
G
H
F2 H1
F1
Attach PLT V-Legs(E) to
Top Panel(A) by using
#6 x 16mm P/H Cross
Recess Screws(F1).
H
F
3
H
H1
A
Attach PLT Square Post
Legs(H) to Top Panel(A)
by using screws #4 x
16mm(H1)
INSTRUCTION:ASSEMBLING TABLE WITH V-LEG BASE
1
®
®
OFFICE FURNITURE
MODEL NO. PL437T HALF
OFFICESOURCE.COM Last Updated: 10/2021
ASSEMBLY INSTRUCTIONS
Part 6 of 6