OFM 700 User manual

A
Chair Back
1 Unit
B
Chair Seat
1 Unit
c
Chair Base
1 Unit
D
Casters
5 Units
E
Gas Lift
1 Unit
F
Telescopic Bellows
1 Unit
Assembly Notes:
During assembly, hand tighten screw only when all screws
are in place, you may then tighten all screws completely.
CAUTION:
1. Do not use this chair as a step ladder.
2. Check for loose screws and tighten them every 6 months.
Model 700 / 700-AA6 Big & Tall Chair
WEIGHT CAPACITY: 400 lbs.
Parts Listing
919-362-4765 (fax)
www.ofminc.com
161 Tradition Trail Holly Springs, NC, 27540
800-520-7471 (voice)
919- 303-6389 (voice)
[email protected]
06.30.2010
D
B
A
C
E
F
Seat
Mechanism
STOP
STOP
Assembly Instructions:
Tools Needed: Philips Head Screwdriver
Please read all instructions before assembly.
Step 1: Insert Casters (D) into Chair Base (C).
Step 2: Insert Gas Lift (E) into Chair Base (C).
Step 3: Cover Gas Lift (E) with Telescopic Bellows (F).
If you are assembling a model with optional AA-6 Arms please
proceed to subsequent pages for armrest assembly instructions.
Step 4: Carefully place Chair Seat (B) with attached seat
mechanism onto the Gas Lift (E), aligning the hole
in the seat mechanism with Gas Lift. Press down
on Chair Seat (B) to secure onto Chair Base (C).
Step 5: Slide Chair Back (A) with attached back support bar
into the slot on the seat mechanism.
Step 6: Hand tighten tension knob on seat mechanism until the
Chair Back (A) is properly secured.
Step 7: Carefully sit on chair to make sure the Gas Lift (E)
is properly inserted into the Chair Base (C).
Step 8: Operate the gas lift lever on the seat mechanism,
to be sure unt is working properly.

Model AA-6 Adjustable Arms for Model 700
A
AA-6 Adjustable Armrest
2 Units
B
M8x30mm Hex Screw
10 Units
C
Washer
10 Units
D
Wrench
1 Unit
Parts Listing
Assembly Notes:
During assembly, hand tighten screw only when all screws
are in place, you may then tighten all screws completely.
CAUTION:
1. Do not use this chair as a step ladder.
2. Check for loose screws and tighten them every 6 months.
919-362-4765 (fax)
www.ofminc.com
161 Tradition Trail Holly Springs, NC, 27540
800-520-7471 (voice)
919- 303-6389 (voice)
[email protected]
04.06.2010
Assembly Notes:
During assembly, hand tighten screw only when all screws
are in place, you may then tighten all screws completely.
CAUTION:
1. Do not use this chair as a step ladder.
2. Check for loose screws and tighten them every 6 months.
919-362-4765 (fax)
www.ofminc.com
161 Tradition Trail Holly Springs, NC, 27540
800-520-7471 (voice)
919- 303-6389 (voice)
[email protected]
04.06.2010
B
D
A
Chair Seat
Forward
Height Adjustment
Button
C
STOP
Assembly Instructions
Tools Needed: Phillips Head Screwdriver
Please read all instructions before assembly.
Step 1: Turn Chair Seat upside down and place on a
clean, non-abrasive surface.
Step 2: Align the pre-drilled holes in the Adjustable Armrest (A)
with the holes in the bottom of the Chair Seat,
making sure that the arms face the correct direction.
Step 3: Place five Washers (C) onto five M8x30mm
Hex Screws (B) and insert through the Armrest (A)
holes and into the Chair Seat.
Step 4: Tighten Screws (B) using supplied Wrench (D)
or screwdriver. It is recommended that to assure
screws are secure, a screwdriver is used to tighten.
To Adjust Arms:
Pull up on the Height Adjustment Button
and slide to desired height.