OHAUS Scout SJX User manual

Quick Start Guide ScoutTM SJX Balances
Ohaus Corporation www.ohaus.com i ScoutTM SJX Balances
UNPACKING
Carefully remove your Scout balance and each of its components from the
package. Store the packaging material to ensure safe storage and future transport.
Included Components:
Balance
Pan
Quick Start Guide
Calibration Mass (only for SJX/E models with 64g capacity)
Warranty Card
Scoop (only for models with 64g capacity)
AC Adapter & Plug
SELECTING THE LOCATION
Place on a firm, steady surface with sufficient space. Avoid excessive air currents,
vibrations, heat sources, or rapid temperature changes.
PREPARATION FOR USE
Step-1
Release the red Transportation Lock
on subplatform of the balance
Turn the pointer 90counter-clockwise.
Notes:
SJXN/E models may have different
transportation protection method.
For SJXN models, the shipping lock
needs to be removed (by pulling it out)
before installing the pan.
Step-2
Install the Pan
For SJX/E:
Rectangular pan: Place diagonally on
sub-platform and rotate counter-
clockwise until it locks.
Round pan: Set straight down on
subplatform.
For SJX: Install the stainless steel pan
directly on the subplatform.
Unlocked
Position
Locked
Position
For SJX/E
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights

ScoutTM SJX Balances Quick Start Guide
ScoutTM SJX Balances ii Corporation www.ohaus.com
Step-3
Connect Power
Connect the AC Adapter to the balance
input jack.
Battery Installation
Install the Four “AA” (LR6) batteries
(not included) with polarity as shown in
the battery compartment.
Step-4
Level the balance
Level the balance before using by
adjusting the feet until the air bubble is
centered
SAFETY PRECAUTIONS
CAUTION: Read all safety warnings before installing, making connections, or
servicing this equipment. Failure to comply with these warnings could result in
personal injury and/or property damage. Retain all instructions for future reference.
Verify that the local AC power supply voltage is within the input voltage
range printed on the AC adapter’s ratings label.
Only connect the AC adapter to a compatible grounded socket.
Position the instrument such that the AC adapter can be easily
disconnected from the socket.
Position the power cord so that it does not pose a potential obstacle or
tripping hazard.
Operate the equipment only under ambient conditions specified in the user
instructions.
Do not operate the equipment in hazardous or explosive environments.
Disconnect the equipment from mains power before cleaning or servicing.
Service should only be performed by authorized personnel.
AC Adapter Jack
Battery
Compartment
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights

Quick Start Guide ScoutTM SJX Balances
Ohaus Corporation www.ohaus.com iii ScoutTM SJX Balances
CONTROLS
Button Functions
Button
Short
Press
Zero/On
Turns the balance
on;
If balance is On,
sets Zero
Print
Initiates print
Function
Initiates an
application mode
Tare
Tare
Long
Press
Extended
Press
Off
Turns the balance
Off
None
Units
Changes the
weighing unit
None
Mode
Changes the
application mode
None
Menu
Enters the user
menu
View the preset
Tare value
Short
Press
(Menu
Function)
Yes
Accepts the current
setting
No
Advances to the
next menu or
setting
Back
Moves to previous
menu item
Exit
Exits the user menu
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights

ScoutTM SJX Balances Quick Start Guide
ScoutTM SJX Balances iv Corporation www.ohaus.com
CALIBRATION
When the balance is operated for the first time, a calibration is recommended to
ensure accurate weighing results.
External Span Calibration
With balance turned on:
Step-1
Press and hold Menu until [mMeNU] (Menu) is displayed.
Step-2
Release the button, the display will show [C.A.L].
Step-3
Press Yes to accept. [SpaN] will then be shown.
Step-4
Press Yes to begin the span calibration. [--C--] will blink and the
Zero reading is stored automatically.
Step-5
The specified mass blinks on the display.
Place the specified span calibration mass on the pan or press
No to select an alternate weight.
[--C--] will blink while the reading is stored.
The display will show [done] if the calibration was successful. The
balance returns to the previous application mode and is ready for
use.
Internal Calibration (not available for SJX/E models)
With balance turned on:
Step-1
Press and hold Menu until [mMeNU] (Menu) is displayed.
Step-2
Release the button, the display will show [C.A.L].
Step-3
Press Yes to accept. [In.CAL] will then be shown.
Step-4
Press Yes to begin the Internal calibration. Zero reading is
stored automatically.
Step-5
Pull the InCal handle while the
display show [PULL].
Step-6
Push the InCal handle while the
display show [PUSH].
Step-7
Repeat the step-5, and step-6 one
more time.
Step-8
The display will show [done] if the calibration was successful.
The balance returns to the previous application mode and is
ready for use.
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights

Quick Start Guide ScoutTM SJX Balances
Ohaus Corporation www.ohaus.com vScoutTM SJX Balances
OPERATION & APPLICATIONS
The balance can be configured to operate in one or more Application modes.
Press and hold Mode key to select your Application mode.
The Scout SJX balance incorporates the following Applications:
[wWeIGH]
[Count]
[Percnt]
[CHeCK]
[total]
[SPEC.Gr]
[Hold]
Weighing
Parts
Counting
Percent
Weighing
Check
Weighing
Totalization
Density
Determination
Display
Hold
Weighing
Step-1
Press the Zero/On button to turn the balance on.
Step-2
Select Weighing (default application) by pressing & holding
Mode key.
Step-3
Press Tare or Zero if necessary to begin.
Step-4
Place objects on the pan to display the weight. When stable, the
appears on the display. The display then shows the resulting
weight of the sample.
MENU STRUCTURE
Sub-Menus
C.a.l**
S.E.t.U.P
M.o.d.E
U.n.i.t**
E.n.d
User Menu Items:
In.CAL*
A.CAL*
On/Off
CAL.Adj*
-100
..
0
..
100
Span
Lin
Reset Yes/No
Filter
Low/Med/High
AZT 0.5/1/3/Off
StableRange
0.5/1/2//5
Backlight
Off/On/Auto
Auto Tare
Off/On/On-acc
Auto Off
Off/1/5/10
Reset Yes/No
Weighing
On/Off
Counting
On/Off
Percent
On/Off
Check On/Off
Totalize
On/Off
Density
On/Off
Hold
Disp/Peak/Off
Reset
g
kg
ct
oz
ozt
dwt
lb
grn
hkt
sgt
twt
ttola/tical
End
End
End
End
Note: Bold fonts are default settings in the menus.
* These sub-menus are not available in SJX/E models.
** Available Settings may vary by local regulations.
No/Back
Long press –
Enter menu
Short press -
Accept
Short press –
Go Next/Prev.
menu
Yes
Exit
Short press –
Exit menu
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights

ScoutTM SJX Balances Quick Start Guide
ScoutTM SJX Balances vi Corporation www.ohaus.com
ADDITIONAL FEATURES
Connecting the Interface
Use an optional interface connectivity
kit to connect the balance either to a
computer, printer or OHAUS auxiliary
display.
Below Interface kit accessories are
available:
RS232, USB Host, USB Device,
Ethernet, Bluetooth*.
Interface connection on the rear of the
balance:
* Interface kits may vary according to local regulations
Weigh Below Hook
The weigh below hook on SJX/E models is located at the reverse
side of the battery cover as shown below (on SJX models it is located in
the weigh below protective cover). To use this feature, remove the red
protective cover underneath for the weigh below opening.
Interface connection
AC Adapter Jack
Security slot
Weigh below protective cover
Weigh below
hook
(SJX/E)
0
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights

Quick Start Guide ScoutTM SJX Balances
Ohaus Corporation www.ohaus.com vii ScoutTM SJX Balances
COMPLIANCE
Compliance to the following standards is indicated by the corresponding mark on
the product.
Mark
Standard
This product complies with the EU Directives 2014/30/EU (EMC),
2014/35/EU (LVD) and 2014/31/EU (NAWI). The EU Declaration of
Conformity is available online at www.ohaus.com/ce.
This product complies with the EU Directive 2002/96/EC (WEEE).
Please dispose of this product in accordance with local regulations at
the collecting point specified for electrical and electronic equipment.
For disposal instructions in Europe, refer to www.ohaus.com/weee.
AS/NZS 61000.6.1, AS/NZS 61000.6.3
CAN/CSA-C22.2 No. 61010-1
UL Std. No. 61010-1
INSTRUCTION MANUAL
For more detailed information about the balance,
please refer to the product instruction manual. The
instruction manual can be obtained either by
scanning the QR code or by going to the Scout
SJX product page to download it.
Go to www.ohaus.com to register your product's
warranty.
Product Page:
http://www.ohaus.com/scout
QR Code:
Visit www.scaleman.com to purchase Ohaus Scout SJX Scale
Visit www.balances.com for balances, scales & calibration weights