Copyright © 2010. All Rights Reserved.
www.okinausa.com 3 REV012011-V06
There are 2 pages of the OSD main menu. Adjust the item with buttons eand f, for the item with sub-menus, click enter to edit it.
Main Menu 1 Main Menu 2
Main Menu 1
yLENS: MANUAL / AUTO<┘
ySHUTTER/AGC: AUTO<┘/ MANUAL<┘
yNR: NR MODE / Y LEVEL / C LEVEL
yWHITE BAL: ATW / PUSH / USER1 / USER2 / ANTI CR /
MANUAL / PUSH LOCK
yATR: OFF / ON<┘
yBACKLIGHT: OFF / BLC / HLC
yDAY/NIGHT: AUTO<┘/ COLOR / B/W
yNEXT<┘: Go to the next page of the main menu.
yEXIT<┘: Exit the OSD menu.
ySAVE ALL<┘: Save all the settings made.
1. Never point the camera toward the sun
Do not expose the lens directly to the sun or to strong light as this may damage the pick-up device.
2. Handle this camera with care
Avoid any shock or bumping of the camera. Improper handling could damage the camera.
3. Requires a proper operating environment
This camera is designed for indoor and outdoor use. The allowable temperature range for operation of this camera is between 14˚F~122˚F /
-10°C~50°C and the allowable humidity is 90%RH maximum.
4. Clean the front face to the pick-up device
It is recommended that the pick-up device surface be cleaned before lens installation or whenever the lens is changed. Cleaning should be done by
using a chamois, a very fine soft cloth, lens tissue, or cotton tipped applicator and ethanol to carefully remove any fingerprint or dust.
5. Check the power source voltage
The power source voltage should be within the specified range. (Camera must meet the specifications). Camera must be connected to a surge
protector at all times.
6. Objects and liquid entry
Never push objects of any kind into this camera as this may touch dangerous voltage points of short out parts that could result in a fire or electric
shock. Never spill any kind of liquid on the video product.
7. Servicing
Do not attempt to service this video product by yourself as opening or removing covers may expose you to dangerous voltage or other hazards.
Refer all service to qualified servicing personnel.
8. Damage requiring service
Unplug this video product from the wall outlet and refer service to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product has been dropped or the cabinet has been damaged.
e. When the video product exhibits a distinct change in performance.
OKINA USA products are covered under warranty for one year from the date of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed
If the camera sticker is removed, we will not be able to confirm any information regarding when and where the product was purchased. We have no
other way to verify the purchase record without the serial number on the camera sticker; therefore, it should not be removed.
2. Camera is modified in any way
If the camera is scratched, damaged, or modified in a manner not described in this manual, the warranty will be voided immediately. It is the
customer’s responsibility to keep the camera in good condition.
3. Video or power cable is cut
The video cable and the power cable should not be tampered with. Cutting or modifying of the cables will result in termination of the warranty.
BASIC SETTINGS
CAUTION
WARRANTY
SETUP MENU
LENS AUTO<┘
SHUTTER/AGC AUTO<┘
NR <┘
WHITE BAL ATW<┘
ATR OFF
BACKLIGHT OFF
DAY/NIGHT AUTO<┘
NEXT<┘
EXIT<┘SAVE ALL<┘
SETUP MENU
PICT ADJUST <┘
MOTION DET ON<┘
PRIVACY OFF
CAMERA ID OFF
LANGUAGE ENGLISH
CAMERA RESET
BACK<┘
EXIT<┘SAVE ALL<┘
Main Menu 2
yPICT ADJUST: MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS /
HUE / GAIN
yMOTION DET: DETECT SENSE / BLOCK DISP / MONITOR AREA /
AREA SEL(TOP / BOTTOM / LEFT / RIGHT)
yPRIVACY: AREA SEL(TOP / BOTTOM / LEFT / RIGHT) / COLOR /
TRANSP / MOSAIC
yCAMERA ID: OFF / ON<┘
yLANGUAGE: ENGLISH / 日本語 / DEUTSCH / FRANCAIS РУССКИЙ /
PORTUGUÊS / ESPAÑOL
yCAMERA RESET: Select to restore all the setting to the default values.
yBACK<┘: Go back to the previous page of the main menu.
yEXIT<┘: Exit the OSD menu.
ySAVE ALL<┘: Save all the settings made.
