Oliver MODEL 619-16 Operation instructions

0619S20000-CVR
Walker, Michigan, U.S.A. 49534
USER’S OPERATING AND INSTRUCTION MANUAL
MODEL 619-16
MODEL 619-20
MODEL 619-24
MODEL 619-24R
DOUGH DIVIDERS

REV. 10/12/2010 0619S20000
MODEL 619-16,20,24,&24R DOUGH DIVIDERS
INDEX
SAFETY INSTRUCTIONS..........................................................................0619S20001
DESCRIPTION/SPECIFICATIONS.............................................................0619S20002
Description/Dimensional Specifications......................................... 0619S20002-1/3
Electrical Specifications/Wiring Diagrams......................................0619S20002-2/3
OPERATION INSTRUCTIONS...................................................................0619S20003
MAINTENANCE..........................................................................................0619S20149
Cleaning.........................................................................................0619S20149-1/7
Cleaning.........................................................................................0619S20149-2/7
Lubrication......................................................................................0619S20149-3/7
Hydraulic Oil Specifications............................................................0619S20149-3/7
Hydraulic Filter Replacement......................................................... 0619S20149-3/7
Removing The Lid..........................................................................0619S20149-3/7
Replacing The Locking Hook Or Cam............................................0619S20149-3/7
Replacing Plastic Bottom Element.................................................0619S20149-4/7
Changing The Blades.................................................................... 0619S20149-4/7
Replacing The Thrust Plate............................................................0619S20149-5/7
Replacing The Hydraulic Cylinder..................................................0619S20149-5/7
Removing The Motor .................................................................... 0619S20149-6/7
Changing The Pump Or Coupling..................................................0619S20149-6/7
Replacing The Control Valve ........................................................ 0619S20149-7/7
TROUBLESHOOTING...............................................................................0619S20005
RECOMMENDED SPARE PARTS LIST....................................................0619S20006
PARTS LIST.............................................................................................. 0619S20146
MAIN FRAME ASSEMBLY DRAWING...................................................... 0619S20008
COVERS ASSEMBLY DRAWING............................................................. 0619S20145
HYDRAULIC ASSEMBLY DRAWING........................................................0619S20010
LID ASSEMBLY DRAWING.......................................................................0619S20011
PUSHER-16 PART ASSEMBLY DRAWING..............................................0619S20043
PUSHER-20 PART ASSEMBLY DRAWING..............................................0619S20012
PUSHER-24 PART (SQUARE) ASSEMBLY DRAWING............................0619S20013
PUSHER-24 PART (ROUND) ASSEMBLY DRAWING .............................0619S20044
WARRANTY...............................................................................................GEN040225
WARRANTY PROCEDURE…………………………………………………… GEN040226
RETURN PARTS POLICY..........................................................................GEN040227

REV. 1-31-96 0619S20001
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
SAFETY INSTRUCTIONS
Every effort has been made by Oliver Products Company to provide you with a safe
machine. It is essential however, that machine operators and maintenance personnel
observe the following safety precautions.
1. Before attempting to operate your divider read this manual. Never allow an
untrained person to operate this machine.
2. Make sure that the machine is only connected to a properly grounded electrical
supply source of sufficient capacity for the load the divider will put on it. Always
unplug the machine when it is not in use.
3. Always make sure the machine has been disconnected from the power supply
before cleaning or servicing.
4. All guards must be in place before starting the machine.
5. Keep your hands away from the moving parts of the machine.
6. Use only proper replacement parts.
7. Do not wear loose fitting clothing. Shirt tails should be tucked in.
8. In addition to these general safety instructions, also follow the more specific safety
instructions given for the different areas of the machine in the operating
instructions.

0619S20002-1
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
DESCRIPTION/SPECIFICATION
Description:
The Oliver divider consists of a hopper which can be loaded with dough from a
minimum of ten and one half pounds up to forty-five pounds. The lid and sides of the
hopper are made of heavy cast aluminum. The moveable hydraulic floor of the hopper
is made of a collection of food grade plastic plates which, when moved upward, will
compress the dough until it completely fills the remaining area. At this point a group of
stainless steel knives come between the plates cutting the dough into equal weight,
easy to use pieces.
This machine is ideal for pizza and bakery operations and is mounted on four casters
for easy movement about the work area. The divider can divide pieces as small as
seven ounces, on a 24 part divider, to as large as forty five ounces, on the 16 part
divider. See below for specific maximums.
The hydraulic pump is powered by a two horse power, totally enclosed motor. The
system has a built-in four and one half gallon hydraulic oil tank making the machine
totally self contained.
Physical specifications
OVERALL MACHINE DIMENSIONS
REV. 1-31-96

0619S20002-2
Physical specifications (continued)
Net Weight:
Approximately 455 pounds.
Shipping Weight:
Approximately 500 pounds.
Product Capacities:
Fill Capacity (approximate) = 10-1/2 to 45 pounds
Divided piece Size (approximate):
16 part dividers = 10-1/2 to 45 ounces
20 part dividers = 8-1/2 to 36 ounces
24 part dividers = 7 to 30 ounces
Electrical Specifications
2 Horse Power, 1 phase, 60 hertz, 230 Volts AC, 10 Amps.
2 Horse Power, 3 phase, 60 hertz, 208 Volts AC, 6.5 Amps.
2 Horse Power, 3 phase, 60 hertz, 230 Volts AC, 6.2 Amps.
2 Horse Power, 3 phase, 60 hertz, 460 Volts AC, 3.1 Amps.
Others consult factory
Electrical Wiring Diagrams
1 ph, 60 hz, 230 VAC
Rev. 1-31-96

0619S20002-3
Electrical Wiring Diagrams (Continued)
3 ph, 60 hz, 208/230 VAC
3 ph, 60 hz, 460 VAC
Rev. 5-24-96

0619S20003-1
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
OPERATING INSTRUCTIONS
Before You Start
CAUTION
THE DIVIDER SHOULD ONLY BE PLUGGED INTO AN OUTLET
WITH THE SAME VOLTAGE AS STATED ON THE NAMEPLATE
Before starting a new divider with THREE PHASE electrical power for the first time you
should check to see if the motor is running in the correct direction. Remove the front
cover by removing the four thumbscrews which secure it; you will also have to remove
the handle from the directional control lever before removing the front cover. Once the
cover has been removed you should be able to see the fan end of the motor on your
divider, this fan MUST rotate in a clockwise direction.
CAUTION
EXTENDED RUNNING OF A DIVIDER WITH THE MOTOR ROTATING
IN THE INCORRECT DIRECTION WILL SEVERELY DAMAGE THE
HYDRAULIC PUMP OF YOUR DIVIDER.
If the motor is rotating in the incorrect direction turn the machine off, disconnect it from
the power supply and have a qualified electrician reverse two of the three power wires
in the plug at the end of the power cord. DO NOT move the ground (green) wire.
WARNING
ALWAYS HAVE ELECTRICAL WORK DONE BY QUALIFIED ELECTRICIANS ONLY.
Recheck the divider making sure that it is now running in the correct direction,
(clockwise looking at the fan end of the motor).
Basic Operation
·Start by weighing out a piece of dough, which, when divided by the number of
compartments available on your divider, will provide you with the desired end
weight. For example: a thirty pound piece of dough after division on a twenty-four
part divider will yield twenty-four twenty ounce pieces, perfect for molding into one
and a quarter pound loaves of bread.
·Make sure the floor of the hopper has been lowered before attempting to open the
lid of the divider.
Rev. 5-5-00

0619S20003-2
Basic Operation (Continued)
·Open the lid and load the preweighed dough into the hopper. Spread the dough
over the floor of the hopper making it approximately the same height, this is done to
eliminate large air pockets and to insure equal division of the dough.
·Close the lid and turn the handle in a clockwise direction making sure it is secure.
·With the machine running grasp the control valve handle and lift it to start the floor
of the hopper up. Hold it in this position until the light on the starter switch box
comes on, this means that the upward stroke has stopped and that division is
complete. Let loose of the valve handle when you see the light come on.
·Press the control valve handle down slightly to release the pressure on the lid so it
can be opened. Open the lid.
·We suggest that the cut pieces of dough be removed as soon as possible to
prevent them from sticking together.
·The above process may now be repeated.
WARNING
NEVER LEAVE DOUGH IN THE MACHINE; RISING DOUGH MAY
CAUSE EXPLOSIVE PRESSURES TO DEVELOP.
WARNING
NEVER FORCE THE LID HANDLE OPEN
·If dough has been left in the machine and the lid handle is difficult to turn,
recompress the dough by lifting the control valve handle until the light come on.
This will raise the floor of the hopper, after doing so lower the hopper floor by
pressing down on the control valve handle. This may have to be done more than
once if dough has been left in the machine for quite awhile. With the hopper floor
all the way down try to open the lid again, the handle should turn easily, if it does
not, recompress the dough and try again.
·The divider is designed so that if dough is left in the hopper it will eventually force
the hopper’s floor to the bottom, thus allowing the dough to vent to the outside of
the machine through openings on the left side. If dough is coming out of these
openings follow the steps above recompressing the dough a number of times
before attempting to open the lid.
Rev. 5-5-00

0619S20149-1
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
MAINTENANCE
WARNING
ALWAYS MAKE SURE THE MACHINE HAS BEEN DISCONNECTED
FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING.
Cleaning
Remove- all scraps from lower pan. Open side doors and brushing out all scraps. Wash all
interior surfaces; Knives, pusher plates, hopper, lid surface with a damp rag and mild soap
solution. The exterior and contact surfaces should be cleaned daily using common cleaners.
The knives should be extended for easier cleaning. This can be done by placing the cleaning
separator, furnished with the machine, IN THE CENTER OF THE HOPPER straddling the
knives. Close the lid and bring the floor of the hopper up until the light on the manual starter is
on, lower the floor slightly. Open the lid and disconnect the divider from the power supply.
Clean the knives and plastic compartment floors of all dough build-up. Rinse all interior surfaces
with a damp rag and clean water. Sanitize all interior surfaces with a damp rag and sanitizing
solution. Air Dry, leave divider lid open and allow interior to air dry before using. SEE
CLEANING
INSTRUCTION SHEET (S20143) AT THE END OF THIS CHAPTER (S20004)
CAUTION
IF NOT CLEANED A BUILD-UP OF DRIED DOUGH BETWEEN THE
PLASTIC FLOORS AND THE KNIVES COULD DAMAGE THE DIVIDER.
In addition to the general cleaning discussed above, it is important that you check for and
remove scraps of dried dough from between the blade holder and the bottom thrust plate. This
can be done by first extending the knives as described above and then by removing the front
cover from the machine by removing the four knobs and the control valve handle. This will allow
access to the blade holder area which can then be cleaned of all dried scraps of dough. When
finished replace the front cover.
Occasionally, as required, you should also remove the build up of flour and dough
particles in the base of the machine around the motor.
CLEANING INSTRUCTIONS FOR THE 619
RUN PRESS ALL THE WAY UP

0619S20149-2
*********W A R N I N G******
UNPLUG MACHINE
USING THE ACCESS DOORS ON BOTH SIDES OF THE UNIT
PULL DOOR UP, USE ONE HAND TO HOLD DOOR UP
WIPE DOWN MACHINE WITH OTHER, USING A RAG
OR A BRUSH
Lubrication
The machine requires no lubrication but the oil level in the hydraulic system should be checked
periodically. To check the oil level remove the rear cover by removing the four knobs which
secure it to the divider, then remove the tank breather/cap and determine where the top of the oil
is in relation to the top surface of the tank. Fill with oil to within approximately one inch of the
top surface. If necessary add HYDRAULIC OIL to return it to the proper level, DO NOT
OVERFILL. In addition to the above we advise replacing the hydraulic oil in the system
approximately every three years.
Hydraulic Oil Specification
The hydraulic oil used in your divider should be made of good quality base stocks compounded
with the following additives: anti-wear, anti-oxidation, antifoaming, and antirust. In addition it
should be an “ISO”viscosity grade No. 32.
Rev. 7-30-02

0619S20149-3
Hydraulic Filter Replacement
At least once a year the throw-away filter on the hydraulic system should be replaced, more
often when under heavy use. To replace the filter remove the front cover unscrew the old filter
and replace it with a new one. The filter is located on the return line near the tank.
Removing The Lid
·Remove the lid cover by removing the four screws which secure it in position.
·Open the lid as far as it will go.
·Release the tension on the two large torsion springs by moving the long leg of the spring to
the side and out from behind the bracket.
WARNING
USE CARE AS THE LID WILL DROP ONCE THE SPRING TENSION
HAS BEEN REMOVED.
·Close the lid and remove the right hand snap ring from the lid hinge pin and push the pin to
the left to remove it.
·Reassemble by reversing the above steps.
Replacing The Locking Hook Or Cam:
·Remove the lid cover by removing the four screws which secure it in position.
·Detach the spring from the hook.
·Open the lid.
·Turn the handle until the pin securing the cam to the shaft is in line with the notch in the
locking hook. Using a small drift punch force the pin upwards removing it from the handle
shaft.
·Pull the shaft and cam assembly forward out of the lid.
·The hook or locking cam can now be replaced.
·Reassemble by reversing the above steps.
Replacing A Plastic Bottom Element
·Open the lid and raise the bottom of the hopper.
·Turn the machine off and disconnect it from the power supply.
·Remove the front and rear panels to gain access to the pusher components.

0619S20149-4
·Remove the nut securing the float to the thrust plate.
·Using a block of wood or other soft material to protect the threads on the float, force the float
and bottom element assembly upwards until it is free from the thrust plate and then lift the
assembly from the blades.
·Once the assembly has been removed, the bottom element can be disassembled from the
float by removing the fasteners from the under side of the element which secure it to the
float.
·Replace each float and element assembly by reversing the above steps.
Changing The Blades
·To ease removal of the blade assembly the front, rear, and side panels should first be
removed from the machine.
·Next remove all of the float and element assemblies, see replacing plastic bottom elements
covered above.
·Remove the nuts securing the four blade holder braces, to the star plate.
·Lift the entire blade assembly, (blades, blade holder, and braces), out of the hopper.
·Once removed, a blade or blades can be replaced. Remember it is important before
securing any blades that the blade holder and knife assembly be inverted on a surface plate
or other known flat surface, verifying that all the blades are level and in with each other. If
no other flat surface is available the lid of the divider could be emoved and used for this
purpose.Once complete, re-insert the assembly in the hopper and reverse the above steps to
re-assemble the machine.
Replacing The Thrust Plate
·Should the thrust plate require replacement you should start by removing the blade assembly
as described above.
·Remove the bolt securing the thrust plate to the cylinder rod. Once this bolt is removed the
thrust plate can be lifted from the machine and replaced.
·When the machine is re-assembled the bolt securing the thrust plate to the cylinder rod
should be installed using “Loctite”adhesive to prevent loosening during operation. The
remaining components can be reinstalled by reversing the above steps.
Replacing The Hydraulic Cylinder
·Using the four wedges extend the knives about half of their travel. Turn the machine off and
disconnect it from the power supply.
·To remove the hydraulic cylinder the front, rear, and side panels must be removed from the
machine.
·Place blocks of wood between the thrust plate and the cylinder mounting channel to secure it
during cylinder removal.

0619S20149-5
·Remove one of the center float assemblies, (see above procedures). Once this has been
done the bolt securing the thrust plate to the cylinder rod can be removed using a universal
socket style wrench.
·Remove the four screws securing the star to the outer cylinder rod.
·Remove the bolts securing both the main starter switch bracket and the limit switch bracket
to the hex support rods. DO NOT disconnect the wires.
·Remove one of the snaprings securing the yoke and safety lock pivot pin. Remove the pin
so that the linkage can be unhooked from the top of the machine.
·Remove the eight screws securing the cylinder to the cylinder mounting channel.
·Remove the four bolts securing the cylinder mounting channel to the lower hex support rods.
·The upper portion of the divider can now be removed and set to one side.
Replacing The Hydraulic Cylinder (Continued)
·Disconnect both high pressure hoses at the cylinder allowing removal of the
cylinder for repair or replacement.
·When the machine is reassembled the bolt securing the thrust plate to the cylinder
rod should be installed using “Loctite”thread locker #242 to prevent loosening
during operation. All other components can be reinstalled by reversing the above
steps.
Removing The Motor
·Remove the front, rear and “Motor Side”panels.
·Remove the four screws securing the pump bracket to the front of the motor.
·Remove the four nuts securing the motor to the base of divider.
·Remove the terminal cover on the motor and disconnect the wiring, remember to note the
wire locations to ease replacement of the motor.
·The motor should now be free and can be removed by sliding the motor out and lifting it free
of the machine.
·Re-assemble by reversing the above steps.
Changing The Pump Or Coupling
·Remove the rear cover and the “Motor Side”panels.
·Loosen the intake hose at the pump, make sure you have something available to catch the
hydraulic oil leaking from the end of the hose when it is disconnected.

0619S20149-6
·Remove the high pressure hose from the outlet side of the pump.
·Remove the four bolts from the feet of the motor which secure it to the base this will allow
the motor to be pivoted slightly to allow pump removal.
·Remove the bolts securing the pump to the bracket, pivot the motor and slide the pump with
its half of the coupling out and free of the motor.
·Replace the pump by reversing the above procedures.
Replacing The Control Valve
·Remove the front and side panels from the divider.
·Disconnect the three high pressure hoses and remove the filter head assembly form
the machine.
·Remove the lower pivot bolt from the lower end of the linkage connecting the valve
and the control handle.
·Remove the four screws holding the valve to the valve mounting plate and remove
the valve from the divider.
·Remove the remaining linkage parts from the old valve and re-install them on the
new valve. The new valve can then be installed in the divider by reversing the
above procedures.
·Once the installation has been completed it IS NOT necessary to adjust the
pressure relief valve to allow proper operation of the divider. Note: Oliver’s valves
are normally preset at the factory and adjustment IS NOT necessary. Should it
become necessary to change the pressure relief setting follow the two steps given
below.
·Connect a pressure gauge at the quick disconnect provided on the high pressure
hose at the pump fitting. Note: a pressure gauge test kit can be purchased from
Oliver Products Co. at additional cost.
·With the pump running use the calibrating screw in the bottom of the valve to set
the pressure at 1100 PSIG secure the calibrating screw in place with the locking
nut once the proper pressure has been achieved.

0619S20005-1
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
TROUBLE SHOOTING GUIDE
The “End of Stroke Light”does not come on.
Possible Causes
·There may be a disconnected wire.
·The bulb may have burnt out.
·The limit switch is not adjusted properly.
·The limit switch is not operating and needs replacement.
The motor “Hums”but will not start.
Possible Causes
·The motor is a dual voltage motor and may be wired for high voltage, but, an
attempt is being made to run it on low voltage.
·The electric supply to the motor is single phase instead of three phase.
·One of the leads of the three phase system has opened.
The motor runs but “Stalls”at either end of the cylinders travel.
Possible Causes
·The incorrect overload relay was installed or the setting of that overload
relay is incorrect.
·The setting of the hydraulic relief valve is to high.
The motor runs “Slowly”but stalls easily before completion of its stroke.
Possible Causes
·The motor is wired for high voltage but is connected to a low voltage supply.
The motor has “Stalled”and can not be restarted.
Rev. 1-31-96

0619S20005-2
Possible Causes
·The overload relay has tripped. Allow the relay about five minutes to cool
and attempt to restart the divider.
The divider is not cutting properly.
Possible Causes
·Dough scraps and flour have accumulated between the blade holder and
the float plate. See “Cleaning”under maintenance.
·Check the oil level in the tank, refill if necessary. See “Lubrication”under
maintenance.
·Check to see if the calibrating screw on the control valve has become loose.
If it has, check the procedure for setting the pressure, given under
“Replacing the Control Valve”in the maintenance section.
Rev. 1-31-96

0619S20006-1
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
RECOMMENDED SPARE PARTS
PART NUMBER PART DESCRIPTION NO. REQ’D.
7024-6101 Extension Spring 1
4605-1000-0028 LH Lid Spring 1
4605-1000-0029 RH Lid Spring 1
5835-7636 Coiled Pin 1
5114-9556 Hydraulic Filter 1
0620-0047 Blade Holder Brace 4
0620-0012-1 Star Plate 1
5757-8081 Limit Switch 1
5709-9924 Starter Enclosure 1
5709-0191 Pilot Light 1
5709-3040 Motor Starter (3-60-460V) 1
5709-3041 Motor Starter (3-60-230V) 1
5709-3042 Motor Starter (3-60-208V) 1
5709-3043 Motor Starter (1-60-230V) 1
SPARE PARTS FOR MODEL 619-16 ONLY
0620-0011-002 Blade Holder 1
0620-0048-002 Plastic Outside Plate 12
0620-0049-002 Plastic Inside Plate 4
0620-0052-003 Large Lower Blade 1
0620-0053-003 Large Upper Blade 1
0620-0054-003 Small Blade 12
0620-0055-003 Outside Blade 8
SPARE PARTS FOR MODEL 619-20 ONLY
0620-0011 Blade Holder 1
0620-0048-003 Plastic Outside Plate 16
0620-0049-003 Plastic Inside Plate 4
0620-0052-001 Large Lower Blade 1
0620-0053-001 Large Upper Blade 1
0620-0054-001 Small Blade 16
0620-0055-001 Outside Blade 12
SPARE PARTS FOR MODEL 619-24 ONLY
0620-0064 Blade Holder 1
0620-0062-001 Plastic Plate 24
0620-0066-001 Lower Blade 3
0620-0065-001 Upper Blade 5
Rev. 8/22/05

0619S20006-2
RECOMMENDED SPARE PARTS (Continued)
PART NUMBER PART DESCRIPTION NO. REQ’D.
SPARE PARTS FOR MODEL 619-24R ONLY
0620-0011-001 Blade Holder 1
0620-0048-001 Plastic Outside Plate 20
0620-0049-001 Plastic Inside Plate 4
0620-0052-002 Large Lower Blade 1
0620-0053-002 Large Upper Blade 1
0620-0054-002 Small Blade 20
0620-0055-002 Outside Blade 16
OPTIONAL SPARE PARTS
0620-0036 Handle Shaft 1
0620-0037-1 Latch Cam 1
0619-0018-001 Handle Rod 1
0619-0019 Handle Hub 1
5911-7001 Handle Knob 1
5148-5623 Valve (Hydraulic) 1
5137-7004 Hydraulic Pump 1
5604-6958 Coupling 1
6303-6613 Motor 3 ph, 60 hz, 208/230/460 VAC 1
6303-6725 Motor 1 ph, 60 hz, 230VAC 1
0620-0050 Outer Plunger (619-16, 619-20, 619-24) 4
0620-0050-001 Outer Plunger (619-24R) 4
0620-0051 Inner Plunger (619-16, 619-20) 2
0620-0051-001 Inner Plunger (619-24R) 2
Rev. 3-7-00

0619S20146-1
MODEL 619-16, 20, 24, & 24R DOUGH DIVIDERS
PARTS LIST
ITEM NO. PART DESCRIPTION PART NO.
001 Brace-Lower W/Holes 0620-0005-001
002 Brace-Lower 0620-0006
003 Plate-Cylinder Support 0620-0007-001
004 Base 0620-0008
005 Plate-Star 0620-0012-1
006 Panel-Separation 0620-0032
008 Actuator-Limit Switch 0620-0044-1
009 Spacer-Cylinder Rod 0620-0045
010 Caster-Ridged 5902-2378
011 Caster-Swivel W/Brake 5902-2377
101 Chute-Round Hopper Dough (Painted) 0619-0027
101 Chute-Round Hopper Dough (Stainless) 0619-0027
101 Chute-Square Hopper Dough (Painted) 0619-0027-008
101 Chute-Square Hopper Dough (Stainless) 0619-0027-008
102
103
103
104
104
105
105
106
106
107
107
108
109
109
110
111
112
113
201
202
203
204
205
206
208
209
210
211
212
213
Plate-Handle Backing
Guard-Top Cover (Painted)
Guard-Top Cover (Stainless)
Cover-Side (Painted)
Cover-Side (Stainless)
Cover-Side W/Chute (Painted)
Cover-Side W/Chute (Stainless)
Cover-Front (Painted)
Cover-Front (Stainless)
Cover-Rear (Painted)
Cover-Rear (Stainless)
Guard Switch
Door Side Cleaning (Painted)
Door Side Cleaning (Stainless)
Hinge Door
Screw-Thumb
Handle Recessed
Handle-Pull
Stirrup
Safety Lock
Rod-Valve Actuating
Clevis-Rod
Rod-Eye
Pin-Long
Rod-Handle
Pin-Stirrup Pivot
Lever-Valve Actuating
Plate-Valve Mtg.
Tank-Oil Powdercoat
Spacer
0619-0028
0620-0001
0620-0001-001
0620-0029-006
0620-0029-008
0620-0029-007
0620-0029-009
0620-0030
0620-0030-003
0620-0031
0620-0031-001
0620-0106
0620-0121
0620-0121-001
0620-0122
5843-0536
5908-5046
0620-0123
0620-0015
0620-0016
0620-0019-002
0620-0020
0620-0021
0620-0022
0620-0024-002
0620-0025
0620-0026-001
0620-0027-001
0620-0069-003
0620-0086
(Continued)
Rev. 04/23/18

0619S20146-2
PARTS LIST
ITEM NO. PART DESCRIPTION PART NO.
214 Hose Clamp 5106-8087
215 Filter Head 5114-9554
216 Filter-Spin On 5114-9556
217 Cylinder-Custom Hydraulic 5108-7818
218 Flange-Tank 5115-0388
219 Fitting-Elbow 5115-2090
220 Fitting-Hose 5115-2079
221 Fitting-Adapter 5115-4031
222 Fitting-Adapter 5115-4032
223 Hose-Bottom Cylinder 5121-8169
224 Flange-Pump Mounting 5137-7375
225 Hose-Pump 5121-8173
226 Hose-Upper 5121-8174
227 Hose-Hydraulic 0619-0016
228 Pump-Vane 5137-7004
229 Tube-Return 5147-0130
230 Valve 5148-5623
231 Breather-Tank 5149-0204
232 Coupling 5604-6958
233 Knob 5911-7001
234 Plate-Cylinder Alignment 0620-0120
235 Nipple-Black Pipe 6203-0407
236 Coupling-Black Pipe 5115-0332
238 Valve-Check 5148-5217
239 Spacer-Pump/Flange 0619-0044
301 Hook-Locking 0620-0017-3
302 Pin-Hinge 0620-0033
303 Clamp-Spring 0620-0034
304 Bracket-Spring 0620-0035
305 Shaft-Handle 0620-0036
306 Cam-Latch 0620-0037-1
307 Rod-Handle 0619-0018
308 Spring-LH 7030-0024
309 Spring-RH 7030-0023
310 Spring-Extension 7024-6101
311 Lid-Round (619-16, -20, -24R) 0619-0022
311 Lid-Square (619-24 Only) 0620-0018-001
313 Hub-Handle 0619-0019
314 Knob-Handle 5911-7001
401 Adj. Upper Brace W/Holes 0619-0023
402 Adj. Upper Milled Brace 0619-0024
403 Adj. Rear Upper Brace 0619-0025
404 Plate-Thrust (619-16) 0620-0009-003
404 Plate-Thrust (619-20) 0620-0009
(Continued)