OLT 12x16 Sunshed Garden User manual

12x16 Sunshed Garden
Shed Interior Wall Kit
Assembly Manual
Version #1.2
Jan 6th, 2020
In the event of a missing or broken piece, call the Outdoor Living Today Customer Support Line @ 1-888-658-1658 with-
in 30 days of the delivery of your purchase. It is our commitment to you to courier replacement parts, free of charge,
within 10 business days of this notification. Replacement parts will not be provided free of charge after the 30 day
grace period.
All structures purchased from Outdoor Living Today are covered for a period of one year for defects in manufacturing
and workmanship. Costs incurred for customer installations are not included.
Failure to use supplied parts included in this kit could result in poor product performance and may void your warranty.
Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from our written instructions.
Thank you for purchasing a 12x16 Sunshed
Garden Shed Interior Wall Kit. Please take the
time to identify all the parts prior to assembly.
Customer agrees to hold Outdoor Living Today and any Authorized
Dealers free of any liability for improper installation, maintenance and
repair.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 1

Thank you for purchasing our 12x16 Sunshed Garden Shed Interior Wall.
Please take the time to identify all the parts prior to assembly.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 2
A. Ceiling Section
1A: 2 - 3/4” x 2 1/2” x 71” - Ceiling Gable Cleats Long
2A: 2 - 3/4” x 2 1/2” x 30” - Ceiling Gable Cleats Short
3A: 1 - 3” x 5 3/4” x 20” - Ridge Cap Sleeve Front
4A: 3 - 3” x 5 3/4” x 44 3/4” - Ridge Cap Sleeve Middle
5A: 3 - 1” x 5 3/4” x 17 3/4” - Ridge Cap Sleeve Rear
6A: 4 - 3/4” x 3 1/2” x 28 1/2” - Gusset Cleats
7A: 4 - 1 1/2” x 2 1/2” x 68” - Roof Cleats Long
8A: 1 - 3/8” x 21” x 71 3/4” - Long Ceiling Plywood Front
9A: 3 - 3/8” x 44 3/4” x 71 3/4” - Long Ceiling Plywood Center
10A: 1 - 3/8” x 18 3/4” x 71 3/4” - Long Ceiling Plywood Rear
11A: 1 - 3/8” x 21” x 30 3/4” - Short Ceiling Plywood Front
12A: 4 - 1 1/2” x 2 1/2” x 30” - Roof Cleats Short
13A: 3 - 3/8” x 44 3/4” x 30 3/4” - Short Ceiling Plywood Center
14A: 1 - 3/8” x 18 3/4” x 30 3/4” - Short Ceiling Plywood Rear
16A: 8 - 1/2” x 3 1/2” x 19” - Interior Soffits
B. Wall Section
1B: 8 - 1 1/2” x 2 1/2” x 19” - Interior Wall Cleats
2B: 2 - 42 3/4”w x 82 1/2”h - Solid Wall Panel Left & Right
3B: 2 - 45 1/4”w x 82 1/2”h - Solid Wall Panel Center
4B: 2 - 42 3/4”w x 82 1/2”h - Double Window Wall Panel Left & Right
5B: 2 - 45 1/4”w x 82 1/2”h - Double Window Wall Panel Center
6B: 4 - 45”w x 82 1/2”h - Single Window Wall Panels
7B: 1 - 45 1/4”w x 82 1/2”h - Solid Rear Wall Panel
8B: 1 - 11 3/4”w x 74 1/2”h - Narrow Front Wall Panel
10B: 1 - 45 1/4”w x 35 5/8”h - Gable Center Panel (Front)
10B: 1 - 45 1/4”w x 26 3/4”h - Gable Center Panel (Rear)
11B: 2 - 44 3/4”w x 18 1/16”h - Gable Panel Left
12B: 2 - 44 3/4”w x 18 1/16”h - Gable Panel Right
13B: 1 - 3/4” x 3 1/2” x 31 1/2” - Top Plate for Bottom Dutch Door
14B: 1 - 3/8” x 31 3/8” x 29 3/16” - Top Door Plywood
15B: 1 - 3/8” x 31 3/8” x 41 3/16” - Bottom Door Plywood
C. Trim Section
1C: 1 - 7/8” x 2” x 72 1/2” - Vertical Door Stop (Jamb)
2C: 1 - 7/8” x 1/2” x 72 1/2” - Vertical Door Stop (Narrow Wall)
3C: 1 - 3/4” x 2” x 33 5/8” - Top Horizontal Door Stop
4C: 1 - 1/4” x 2” x 72 5/8” - Vertical Door Trim
5C: 1 - 1/2” x 2 1/2” x 33 1/2” - Horizontal Door Trim
8C: 4 - 1/4” x 2” x 71 1/4” - Gable Ceiling Trims
11C: 8 - 1/4” x 2” x 55” - Gable Trims (Top & Bttm.)
7C: 6 - 1/4” x 2” x 58” - Horizontal Side Wall Trims
12C: 6 - 1/4” x 2” x 82 1/4” - Vertical Side Wall Trims
13C: 4 - 1/2” x 1 1/2” x 41 1/4” - Single Rafter Bottom Trims
14C: 3 - 1/2” x 3” x 41 1/4” - Double Rafter Bottom Trims
15A: 4 - 1/4” x 2 1/2” x 31” - Ceiling Trims
15C: 4 - 21 1/16” x 26 3/8” - Large Window Inserts
16C: 8 - 16 3/4” x 24” - Small Window Inserts
D. Potting Shelves - Optional
1D - Potting Shelf Legs - 20 pcs @1 1/2” x 2 1/2” x 35”
2D - Extra Siding Pieces
Steps
Steps
Steps
Steps
1
1
2
3
3
4
5
6
7
8
9
10
11
12
13
14
15 - 16
17
18
19
20
21
22
23
26
24, 26
25, 26
27 - 28
29
30
32
33
34
35
36
37
38
39
40
40
41
42
44
45
31
42

2 1/2”
1 1/4”
Hardware Kit (Provided)
Safety Glasses Work Gloves
Safety Equipment Required (Not Provided)
2 Ladders
Screw Gun/Drill Tape Measure
Hammer Level
Tools Required (Not Provided)
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 3
1/8” Drill Bit
12X16 Sunshed Interior Wall Kit HARDWARE PACKAGE
Optional Materials and Tools - Not Included in Kit
Materials to Insulate Shed prior to installing Interior Wall Kit
2” thick Foam Board Insulation
550 sq ft. (covers walls and ceiling)
180 sq ft additional for floor
6 mm Poly - Air Vapor Barrier -
Tools -
Staple Gun
Utility Knife
Caulking Gun and Caulking
Med. Barrel Bolt
-12 pcs
S1 - 2 1/2” Screws - 120
S2 - 1 1/4” Screws - 275
N1 - 1 1/2” Finishing Nails - 350
BR1 - Square Drive Bit
Y3 - Black Handle
SB1 - 3/4” Screws
Black Headed
Wood Clamp

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 4
Exploded view of all parts necessary to complete Interior Ceiling Section. Please Identify all parts
prior to starting your project.
Ceiling Trim 4 pcs
Ridge Cap Sleeves-
5 pcs
Ceiling Section Exploded
1. Locate long and short cleats. Position cleat on top
of gable framing tight against rafter. Clamp and screw
to gable frame with 3 - 2 1/2” screws in short cleat
and 3 - 2 1/2” screws in long cleat.
A. Ceiling Section
Parts
1A - Ceiling Gable Cleats
(3/4” x 2 1/2” x 71”) x 2
2A - Ceiling Gable Cleats
(3/4” x 2 1/2” x 30”) x 2
Hardware
S1 - 2 1/2” Screws
x 12 total
Ceiling Gable
Cleats 4 pcs
Ceiling Plywood-
(Front) Long
Ceiling Plywood -
Center Short - 2 pc
Interior Soffits -
8 pcs
Ceiling Plywood -
(Front) Short -1 pcs
Rafter Cleats -
4 pcs
Gusset Cleats -
4 pcs
Ceiling Plywood-
(Rear) Long
Ceiling Plywood-
(Center) Long
Ceiling Plywood -
(Rear) Short -1 pcs

2. Lift up the 20” Ridge Cap Sleeve and
position over ridge board near the door of
your shed. Leave 1” gap from gable wall.
Screw from underside of sleeve using
3 - 1 1/4” screws.
3. Push second, third, and fourth sleeves (44 3/4”) tight between Gussets and attach as
per Step 2. Attach final sleeve (17 3/4”) over Ridge Board at rear of shed. At the rear of your
shed leave a 1” gap between Gable and Ridge Sleeve as per Step 2.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 5
Parts
3A,4A,5A - Ridge Cap Sleeve
(3” x 5 3/4” x 20”) x 1
(3” x 5 3/4” x 17 3/4”) x 1
(3” x 5 3/4” x 44 3/4”) x 3
Hardware
S2 - 1 1/4” Screws
x 30 total
1” Gap
4. Locate Gusset Cleats (22.5 cut one end) and
position on Rafter flush with Gusset. Attach
Gusset Cleat to Rafter with 3 - 1 1/4” screws.
Complete remaining three Gusset Cleats.
Parts
6A - Gusset Cleats
(3/4” x 3 1/2” x 28 1/2”) x 4
Hardware
S2 - 1 1/4” Screws
x 12 total
Gusset Cleats

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 6
5. Locate Roof Cleats and position flush with
Gusset and Gusset Cleat. Attach Roof Cleat to
Gusset and Gusset Cleat with 4 - 2 1/2” screws
per cleat.
Parts
7A - Roof Cleats Long
(1 1/2” x 2 1/2” x 68”) x 4
Hardware
S1 - 2 1/2” Screws
x 16 total
6. Locate long ceiling plywood (21” wide) and
position up against rafter and ceiling gable cleat.
Position squarely and attach with
12 - 1 1/4” screws.
Parts
8A - Long Ceiling Plywood
(front)
(3/8” x 21” x 71 3/4”) x 1
Hardware
S2 - 1 1/4” Screws
x 12 total
Rafter Cleats
7. Locate and position center ceiling plywood
(44 3/4” wide) panels and position against Rafters
and Roof Cleats. When positioned correctly,
attach to Rafter and Roof Cleat with
12 - 1 1/4” screws. Complete three sections.
Parts
9A - Long Ceiling Plywood
(Center)
(3/8” x 44 3/4” x 71 3/4”) x 3
Hardware
S2 - 1 1/4” Screws
x 36 total

9. Locate and position front ceiling plywood
panel below Rafter and Gable Cleat. Attach panel
to Rafter and Gable Cleat with 8 - 1 1/4” screws.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 7
Hardware
S2 - 1 1/4” Screws
x 8 total
8. Locate and position rear ceiling plywood
panel (18 3/4” wide) and position against Rafters
and Roof Cleats. When positioned correctly,
attach to Rafter and Roof Cleat with
12 - 1 1/4” screws. Complete three sections.
Parts
10A - Long Ceiling
Plywood (Rear)
(3/8” x 18 3/4” x 71 3/4”) x 3
Hardware
S2 - 1 1/4” Screws
x 12 total
Parts
11A - Short Ceiling
Plywood (Front)
(3/8” x 21” x 30 3/4”) x 1
10. Locate Roof Cleats Short and one Short Ceiling
Panel. Place Roof Cleat Short flush to Gusset. Attach
Cleat to Gusset using 3 - 2 1/2” screws per Cleat. Hold
a ceiling panel flush to rafter to help you line up the
cleat.
Hardware
S1 - 2 1/2” Screws
x 12 total
Parts
12A- Roof Cleat Short
(1 1/2” x 2 1/2” x 30”) x 4

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 8
11. Locate and position center ceiling plywood
panels below Rafter and Short Roof Cleat. Attach
panel to Rafter and Gable Cleat with
8 - 1 1/4” screws. Complete three panels.
Hardware
S2 - 1 1/4” Screws
x 24 total
Parts
13A - Short Ceiling
Plywood (Center)
(3/8” x 44 3/4” x 30 3/4”) x 3
12. Locate and position rear ceiling plywood
panel below Gable Ceiling Cleat and Short Roof
Cleat. Attach panel to both Cleats with
8 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 8 total
Parts
14A - Short Ceiling
Plywood (Rear)
(3/8” x 18 3/4” x 30 3/4”) x 3
13. Locate Interior Soffits. Interior Soffits sit tight up
against Polygal Panels and Polygal Support Cleats.
Soffits may need to be cut short to fit correctly.
Attach each with 4 - 1 1/2” Finishing Nails. Nail into
edge of short ceiling plywood. Complete all 8.
Hardware
N1 - 1 1/2” Finishing
Nails
x 16 total
Parts
16A - Interior Soffits
(1/2” x 3 1/2” x 19”) x 8
Tight against Polygal
Support Cleat
Flush
Tight against
Polygal

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 9
B. Wall Section
14. Position two Interior Wall Cleats against
side wall in corner. Attach each Cleat with
2 - 2 1/2” screws. Attach cleats to each corner of
your shed. Cleat provides an edge to screw
Interior Wall Panel to in Step 15.
Hardware
S1 - 2 1/2” Screws
x 16 total
Parts
1B - Interior Wall Cleats
(1 1/2” x 2 1/2” x 12”) x 8
15. Locate Left Solid Wall Panel (42 3/4” wide).
The left panel will have wall siding recessed on
the left side as illustrated above. Position on wall
studs and secure with 6 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 6 total
Parts
2B - Solid Wall Panel Left
(42 3/4”w x 82 1/2”) x 1
Siding recessed on
left side of panel.
16. Locate Right Solid Wall Panel
(42 3/4” wide). The right panel will have wall
siding recessed on the right side as illustrated
above. Position on wall studs and secure with
6 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 16 total
Parts
2B - Solid Wall Panel Right
(42 3/4”w x 82 1/2”) x 1
Siding recessed on
right side of panel.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 10
17. Locate Center Solid Wall Panel
(45 1/4” wide). Center Wall Panels have siding
flush with plywood backing. Position between
previously installed panels and secure with
6 - 1 1/4” screws.Complete both center panels.
Hardware
S2 - 1 1/4” Screws
x 12 total
Parts
3B - Solid Wall Panel
Center
(45 1/4”w x 82 1/2”) x 2
Pre-drill siding
with 1/8” drill bit
18. Locate Double Window Wall Panels Left &
Right (42 3/4” wide). the panels have recessed
siding as per Steps 15-16. Position on wall studs
and secure as previously illustrated.
Hardware
S2 - 1 1/4” Screws
x 12 total
Parts
4B - Double Window Wall
Panels (L&R)
(42 3/4”w x 82 1/2”) x 2
19. Locate Double Window Wall Center Panels
(45 1/4” wide). Panel wall siding will be flush with
plywood backing. Position between previously
installed panels on wall studs and secure with
6 - 1 1/4” screws per panel. Complete both panels.
Hardware
S2 - 1 1/4” Screws
x 12 total
Parts
5B - Double Window Wall
Panels (Center)
(45 1/4”w x 82 1/2”) x 2
Pre-drill siding
with 1/8” drill bit

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 11
20. Locate Single Window Wall Panels
(45” wide). All single window wall panels are built
the same. Position in front corner. Slide edge tight
in corner against side wall plywood backing.
Adjust panel so window openings match. Secure
with 6 - 1 1/4” screws. Complete each corner.
Hardware
S2 - 1 1/4” Screws
x 24 total
Parts
6B - Single Window Wall
Panels
(45”w x 82 1/2”) x 4
21. Locate Solid Center Wall Panel
(45 1/4” wide). Center panel wall siding is flush
with plywood backing. Position between
previously installed panels on wall studs and
secure with 6 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 6 total
Parts
7B - Solid Rear Wall Panel
Center
(45 1/4”w x 82 1/2”) x 1
22. Position and attach Narrow Wall Panel next
to door on wall framing. Attach with
6 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 6 total
Parts
8B - Narrow Front Wall
Panel
(11 3/4”w x 74 1/2”) x 1

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 12
23. Lift up Front Center Gable Panels and slide
notch up against roof Ridge Board. Once Gable
Panel is aligned correctly, attach to gable framing
with 4 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 4 total
Parts
10B - Front Gable Center
Panel
(45 1/4” x 35 5/8”) x 1
Pre-drill siding with 1/8” drill
bit before attaching Gable
Panel.
24. Locate Front Gable Panel Left and position in
front corner against gable framing. When positioned
correctly, gable siding will overhang window wall siding
with plywood backing pushed tight together. Attach
with 4 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 4 total
Parts
11B - Front Gable Left
Panel
(44 3/4” x 18 1/16”) x 1
Gable siding overhangs wall siding.
Pre-drill siding with 1/8” drill
bit before attaching Gable
Panel.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 13
25. Locate Front Gable Panel Right and posi-
tion in front corner of gable framing. Position and
attach as per Step 24.
Hardware
S2 - 1 1/4” Screws
x 4 total
Parts
12B - Front Gable Right
Panel
(44 3/4” x 18 1/16”) x 1
26. Attach Rear Gable Panels as per Steps 23 - 25.
Hardware
S2 - 1 1/4” Screws
x 12 total
Parts
10B - Rear Gable Center Panel
(45 1/4” x 26 3/4”) x 1
11B - Front Gable Left Panel
(44 3/4” x 18 1/16”) x 1
12B - Front Gable Right Panel
(44 3/4” x 18 1/16”) x 1
27. To accomodate Interior Door Plywood, the existing top plate on bottom door must be removed
first. Using a hammer, carefully pry off the top plate and remove any hardware.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 14
28. Position replacement top plate on bottom
door and attach with 6 - 1 1/2” Finishing Nails.
Replacement Top Plate will cap door siding.
Hardware
N1 - 1 1/2”
Finishing Nails
x 6 total
Parts
13B - Top Plate for Bottom
Dutch Door
(3/4” x 3 1/2” x 31 1/2”) x 1
29. Position top door plywood over door fram-
ing. Confirm it is evenly spaced on door framing
and attach with 12 - 1 1/2” finishing nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 12 total
Parts
14B - Top Door Plywood
(3/8” x 31 3/8” x 29 3/16”) x 1
30. Position bottom door plywood on door.
Position tight under new top cap and attach with
12 - 1 1/2” finishing nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 12 total
Parts
15B - Bottom Door Plywood
(3/8” x 31 3/8” x 41 3/16”) x 1

1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 15
C. Trim Section
31. Locate all 3 door stops. Start on the door
jamb side, position 2” wide stop against door
jamb and the edge of wall siding. Attach with
4 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 4 total
Parts
1C - Vertical Door Stop - Jamb
(7/8” x 2” x 72 1/2”) x 1
32. Position and attach the narrow wall door
stop on framing with 6 - 1 1/2” finishing nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 6 total
Parts
2C - Vertical Door Stop -
Narrow Wall
(7/8” x 1/2” x 72 1/2”) x 1
33. To complete the door stops, attach the
Horizontal Door Stop against Door Header and
attach with 3 - 1 1/4” screws.
Hardware
S2 - 1 1/4” Screws
x 3 total
Parts
3C - Top Horizontal Door Stop
(3/4” x 2” x 33 5/8”) x 1

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 16
34. Locate Vertical Door Trim. Vertical Door
Trim cover seams around the door and Narrow
Wall. Position each piece over Narrow Wall
Door Stop and wall seam. Attach each with
6 - 1 1/2” Finishing Nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 6 total
Parts
4C - Vertical Door Trim
(1/4” x 2” x 72 5/8”) x 1
35. Locate Horizontal Door Trim and position on
Door Header, tight against vertical Trim from the
previous step. Horizontal trim will have an addition-
al piece of wood pre-attached to the reverse face
to make it sit flush to the wall. Attach trim with
3 - 1 1/2” Finishing Nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 3 total
Parts
5C - Horizontal Door Trim
(1/2” x 2 1/2” x 33 1/2”) x 1
Filler Trim attached
on back

1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 17
37. Locate Gable Trims. Gable Trims (Top) have a
22.5° cut at the top to match Gable Ceiling Trims.
Gable Trims (Bttm.) have a straight cut end and a
bevel cut end. Gable Trim (Bttm.) will need to be
chopped at the bottom to fit your ceiling position.
Both pieces have a bevel cut where they meet in
the middle. Attache each piece with
3 - 1 1/2” Finishing Nails. Cover remaining seams
on front walls.Complete front and rear of shed.
Hardware
N1 - 1 1/2”
Finishing Nails
x 24 total
Parts
10C - Gable Trims (Top)
(1/4” x 2” x 55”) x 4
11C - Gable Trims (Bttm.)
(1/4” x 2” x 55”) x 4
36. Locate Gable Ceiling Trims. Position against
gable wall siding and bottom of ceiling plywood. Trims
will butt up against Ridge Cap Sleeves and Horizontal
Side wall Trims. Attach each piece with
6 - 1 1/2” Finishing Nails. Complete front and rear of
shed.
Hardware
N1 - 1 1/2”
Finishing Nails
x 24 total
Parts
8C - Gable Ceiling
Trims
(1/4” x 2” x 71 1/4”) x 4

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 18
39. Locate Vertical Side Wall Trims. Position over
seams in side walls on both sides of shed. Attach
each piece with 6 - 1 1/2” Finishing Nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 36 total
Parts
12C - Vertical Side Wall
Trims
(1/4” x 2” x 82 1/4”) x 6
40. Attach Rafter Bottom Trims to cover under-
side of Rafters with Cedar Trim. Position under
the Rafter and fasten with
5 - 1 1/2” Finishing Nails per piece.
Hardware
N1 - 1 1/2”
Finishing Nails
x 36 total
Parts
13C,14C - Rafter
Bottom Trims
(1/2” x 1 1/2” x 41 1/4”) x 4
(1/2” x 3” x 41 1/4”) x 3
38. Locate Horizontal Side Wall Trims. Position trims
up against wall siding and below ceiling plywood and
Rafters. Evenly space trims on side walls and attach
each piece with 4 - 1 1/2” Finishing Nails.
Hardware
N1 - 1 1/2”
Finishing Nails
x 24 total
Parts
7C - Horizontal Side
Wall Trims
(1/4” x 2” x 58”) x 6

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 19
42. Locate the 4 large Window Inserts and
position in window cavity. Nail to window wall
framing with 9 - 1 1/2” Finishing Nails from the
bottom and sides. Complete the smaller window
inserts in the same fashion.
Hardware
N1 - 1 1/2”
Finishing Nails
x 108 total
Parts
15C - Large Window Inserts
(21 1/16” x 26 3/8”) x 4
16C - Small Window Inserts
(16 3/4” x 24”) x 8
43. Attach barrel bolt to door
plywood. Male bolt attached to top while female
to bottom door. Attach door handle to top door.
Use 3/4” black headed screws for both pieces.
Hardware
SB1 - 3/4” Black
Head Screws
x 12 total
Parts
Barrel Bolt &
Door Handle
Pre-drill siding
with 1/8” drill bit.
41. Locate Ceiling Trims and position over seam
evenly to cover gaps between long ceiling pan-
els.Attach each trim piece with
4 - 1 1/2” Finishing Nails.
Hardware
N1 - 1 1/2” Finishing
Nails
x 16 total
Parts
15A - Ceiling Trims
(1/4” x 2 1/2” x 31”) x 4

1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 20
D. Potting Shelves - Optional
44. If you decide to use the Potting Shelves that came with your
12x16 Sunshed, this Interior Kit includes 20 Shelf Legs (4 Legs
per Shelf). The Legs that came with your Sunshed will have angle
cut ends, which will not work with the Interior Kit.
Fasten a square cut Leg in each corner of the shelf as illustrated,
attach with 2 - 2 1/2” Screws per Leg.
Parts
1D - Potting Shelf Legs
(1 1/2” x 2 1/2” x 35”) x 20
Hardware
S1 - 2 1/2” Screws
x 32 total
45. Position the Potting Shelves inside your Sunshed as desired, but the
above configuration provides optimal sunlight exposure from the Polygal
Roof and Windows. Attach the Shelves together with 2 - 2 1/2” Screws to
make them into a continuous Bench. You may also want to carefully
screw the Bench to the wall in a couple concealed spots to keep it in
place. Extra 2 1/2” Screws will be included in your hardware pack for this.
Hardware
S1 - 2 1/2” Screws
x 10 to 14 total