OLT 12x12 Space Maker Garden Shed with Plywood Roof & AK... User manual

12x12 Space Maker Garden Shed
with Plywood Roof & AK Siding
Assembly Manual
Revision #1.0
Aug 17, 2021
Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 1
Safety Points and Other Considerations
Our products are built for use based on
proper installation and normal residential
use, on level ground. Please follow the
instruction manual when building your
shed and retain the manual for future
maintenance purposes.
Thank you for purchasing a
12x12 SpaceMaker Garden
Shed from Outdoor Living
Today. Please take the time
to identify all the parts prior
to assembly.
Important Information:
- It is the sole responsibility of the customer to check with your local municipal or county by-laws before
ordering this product to confirm it complies with building codes in your area.
- If the product is elevated, any structural and building code requirements are solely the customer's
responsibility, and should be abided by.
- Customer agrees to hold Outdoor Living Today free of any liability for improper installation, maintenance and
repair of any of our products.
- Snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the
snow off the roof(s).
- In high or gusty wind conditions it is advisable to keep the structure securely grounded.
- Have a regular maintenance plan to ensure screws, doors, windows and parts are tight.
- In the event of a missing or broken piece, call the Outdoor Living Today Customer Support Line
@ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our commitment to you to courier
replacement parts, free of charge, within 10 business days of this notification. Replacement parts will not be
provided free of charge after the 30 day grace period.
- All structures purchased from Outdoor Living Today are covered for a period of one year for defects in manu-
facturing and workmanship. Costs incurred for customer installations are not included.
- Failure to use supplied parts included in this kit could result in poor product performance and may void your
warranty. Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from our written
instructions.
Roof Area: 160 sqft

What to do before my Shed arrives?
Become familiar with this assembly manual and determine if you can•
complete the project yourself or will require a professional contractor.
Clear the construcon area and ensure a clear pathway for delivery when•
the freight company arrives. Remove all debris: roots, grass, rocks, etc.
Excavate the site. Contact your local ulies company to ensure there are•
no gas or electric lines buried in the area before digging.
Decide on the type of foundaon you will be using:•
 Concrete slab, or
 46 inches of crushed gravel with paver stones or 4x4 stringers.
You can find the footprint for your shed on Page 3 of your Assembly Manual.
If doing the assembly yourself, have all the necessary tools ready to go and in•
working condion. A list of required tools can be found aer the parts list.
One helper is recommended to assist in construcng your shed.•
It generally takes two people 3 to 4 days to assemble a shed. If you’re hir
ing a contractor, their rate should be in line with that duraon of work.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 2

Foundation Types for 12x12 Garden Shed
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Concrete Slab Foundation:
- Slab must be at least the same size as assembled floor frame (141 1/2” x 136 1/2”) or larger.
- 6” Deep foundation.
- 2.5 Cubic Yards of concrete required.
- A concrete slab will have the longest durability out of your foundation options.
Once level, a concrete slab is the easiest surface to build on.
Gravel with 4x4 Pressure Treated Stringers:
- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 3.0 Cubic Yards of gravel required, approximately 27 wheelbarrows.
- 7 - 4x4 Pressure Treated Stringers 12’ long required.
- Evenly spaced, with one at each end of floor frame.
Saves money on materials, easy to level and work with.
Gravel with Patio Paver Stones:
- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 3.0 Cubic Yards of gravel required, approximately 27 wheelbarrows.
- 35 patio pavers (8” x 8” or larger).
- Center patio paver stones underneath floor runners and underneath seams in floor joists.
Patio paver stones are widely available from most landscape stores.
141 1/2”
136 1/2”
6” Deep
7 - 4”x4”x144”
35 Patio Stones
Floor Frame
Concrete Foundation Completed Foundation
18 5/8”
Gravel Foundation Gravel Foundation with treated stringers Completed Foundation
Gravel Foundation Completed Foundation
Gravel Foundation with Patio Pavers
Front Side Front Side Front Side
Front Side Front Side Front Side
Front Side Front Side
141 1/2”
136 1/2”
153 1/2”
148 1/2”
Front Side
153 1/2”
148 1/2”
Page 3

Thank you for purchasing our 12x12 SpaceMaker Garden Shed.
Please take the time to identify all the parts prior to assembly.
1. Floor Section
Floors
3 - 45 1/2” x 75” - Floor Joist Frames - Large
3 - 45 1/2” x 66 1/2” - Floor Joist Frames - Small
6 - 1 1/2” x 3 1/2” x 72” - Floor Joists Large - Unattached
6 - 1 1/2” x 3 1/2” x 63 1/2” - Floor Joists Small - Unattached
5 - 1 1/2” x 3 1/2” x 76 1/2” - Floor Runners
5 - 1 1/2” x 3 1/2” x 60” - Floor Runners
3 - 5/8” x 45 1/2” x 75” - Floor Plywood Large
3 - 5/8” x 45 1/2” x 66 1/2” - Floor Plywood Small
2. Wall Section
Main Wall Panels
9 - 45 1/2” x 81 3/4” - Solid Wall Panels
9 - 1 1/2” x 2 1/2” x 45 1/2” - Bottom Wall Plates
2 - 34 3/4” x 81 3/4” - Narrow Window Wall Panels
Door Headers
2 - 1 1/2” x 3 1/2” x 73” - Vertical Door Jambs
1 - 1 1/2” x 2 1/2” x 70” - Door Header Riser
1 - 1 1/2” x 7 1/4” x 70” - Door Header
2 - 1/2” x 7 1/4” x 70” - Door Header Spacer
1 - 67” long - Drip Edge with Bevel Siding attached
Top Wall Plates & Gables
4 - 1 1/2” x 2 1/2” x 70 3/4” - Front & Rear Riser Plates
4 - 1 1/2” x 2 1/2” x 65 3/4” - Side Riser Plates
4 - 3/4” x 2 1/2” x 45” - Front & Rear Top Plates (angle cut ends)
2 - 3/4” x 2 1/2” x 51 1/2” - Front & Rear Top Plates (straight cut ends)
4 - 3/4” x 2 1/2” x 35 3/4” - Side Top Plates (angle cut edge)
2 - 3/4” x 2 1/2” x 60” - Side Top Plates (angle cut edge)
4 - Triangular Gable Walls (end tip tucked inside)
3. Rafter and Roof Section
Rafter Assembly
2 - 3/4” x 9 1/4” x 68 1/4” - Roof Ridge Boards
3 - 3/4” x 9 1/4” x 45 1/2” - Roof Ridge Boards
18 - 1 1/2” x 3 1/2” x 80 7/8” - Roof Rafters (angle cut ends)
4 - 1/2” x 4 1/2” x 68 1/4” - Soffits
3 - 3/4” x 80” x 19 3/4” - Triangular Roof Gussets
Roof
6 - 5/8” x 48” x 81 1/2” - Roof Plywood
17 - 22
Steps
Steps
23 - 28
Steps
9 - 16
1 - 8
29 - 42
Parts List - Page 2
Continued on next page
43 - 46
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 4

47 - 56
Steps
4. Trim & Miscellaneous Section
Outer Wall Trim & Door
9 - 3/4” x 4 1/2” x 45 1/4” - Bottom Skirting (Bevel) - Solid Wall
2 - 3/4” x 4 1/2” x 33 3/4” - Bottom Skirting (Bevel) - Window Wall
1 - 3/4” x 4 1/2” x 68 1/2” - Bottom Skirting (Bevel) - Door
4 - 7/8” x 2 1/2” x 81 3/4” - Filler Trims
6 - 3/4” x 1 1/2” x 45 1/4” - Top Wall Trims
3 - 3/4” x 4 1/2” x 45 1/4” - Horizontal Gable Trims (Rear) - Bevel
1 - 3/4” x 4 1/2” x 68 1/2” - Horizontal Gable Trims (Door) - Bevel
2 - 3/4” x 4 1/2” x 32 1/4” - Horizontal Gable Trims (Window) - Bevel
8 - 1/2” x 2 1/2” x 87” - Side Trims
4 - 1/2” x 5 1/2” x 90” - Wide Corner Trims
2 - 1/2” x 2 1/2” x 85” - Rear Wall Trims
2 - 1/2” x 3 1/2” x 85” - Vertical Door Trims
Facia Trim
8 - 3/4” x 1 1/2” x 40” - Facia Cleat
4 - 3/4” x 5 1/2” x 81 1/4” - Front and Rear Facia Angled
4 - 3/4” x 5 1/2” x 71 1/4” - Side Facia
2 - 9 1/2” x 7 3/8” - Pentagon Detail Plates
2 - 8” x 5 1/2” Facia Detail Plates
4 - 8” x 4 1/2” Front & Rear Detail Plates
Miscellaneous
2 - 31 1/2” x 72” - Left & Right Doors (1 each)
2 - 1/2” x 2 1/2” x 72” - Interior Vertical Door Stops
1 - 1/2” x 2 1/2” x 68” - Interior Horizontal Door Stop
1 - 3/4” x 2 1/2” x 62 1/2” - Door Threshold
1 - 1/2” x 2 1/2” x 71” - Interior Door Flange
2 - Regular Window Inserts
2 - Regular Window Trim Pkgs
2 - Flower Box Kits
2 - Spare Bevel Siding
1 - Spare Lap Siding
2 - Spare Shingles - use to shim door, etc
63 - 73
57- 62
Advice: Wood has a tendency to split when
screwing near the ends of a board. To prevent
splitting, it is always recommended to pre-drill
pilot holes before screwing into these areas.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 5
Note: Trim Pieces are to be installed with the rough side facing out. Rough side is graded as best
face.

12x12 SPACEMAKER WITH PLY ROOF HARDWARE SHEET
Safety Glasses Work Gloves
Safety Equipment Required (Not Provided)
Ladder
Screw Gun/Drill Tape Measure
Hammer Wood Clamp
Level Pliers
Tools Required (Not Provided)
1/8” Drill Bits
Caulking Gun
2 1/2”
2”
1 1/4”
3/4”
2”
3/4”
Tee Hinge x6 Pull Handle x 2 Ridge Board
Connector x 3
Silver
Square Drive Bit
Hardware Kit (Provided)
Black Barrel Bolt
1 1/2” Finishing
400 pcs
245 pcs
39 pcs
505 pcs
24 pcs
23 pcs
650 pcs
2 pcs
Black Headed
Black Headed
Single Rafter
Bracket x 6
(22°)
Double Rafter
Bracket x 4
(22°)
Y6 - Cane Bolt
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 6

Regular Maintenance & Tips to prolong the life of your shed.
Before/During Assembly:
1.) Paint each face and edge of your plywood floor with a latex exterior paint.
2.) Caulk wall seams if gaps appear.
3.) Caulk around window framing.
4.) Caulk perimeter between floor plywood and bottom wall plate.
5.) Caulk channels in lap siding at the top of your door above the trim, just a drop in each channel.
6.) Caulk edge of door threshold.
7.) Optional: Install a Sill Gasket between floor runners and foundation.
8.) Optional: Install an 8” strip of roofing paper below Cedar Ridge Caps for Cedar Roof Sheds.
Routine Maintenance:
- Routinely check all fasteners are tight (ex. Door Hinges, Nails)
- Brush off dirt from walls.
- Brush off snow from roof regularly.
- Routinely remove needles and leaves from roof.
Painting/Staining
- Your cedar shed, if left untreated, will weather to a silvery grey color.
- Painting or staining your structure is highly recommended and will prolong the life of your shed.
- You do not need to wait to paint or stain your shed, the wood in your kit has been dried and can be
—stained or painted immediately.
- Consult your local paint store for the best paint or stain for cedar.
- Optional: stain the inside of your shed. (Note: this will remove the fresh cedar smell.)
1. 2. 3.
4. 5. 6.
7.
Sill Gasket
Floor Joists
Floor Runner
Foundation
8.
Floor Plywood
Wall Panel
Small gap between
bevel siding and
window trim
Dab of caulking
Strip of roofing paper over
apex of roof panels
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 7

A. Floor Section
Floor Frames (3)
75” x 45 1/2”
Floor Runners (5)
3 1/2” x 76 1/2”
Plywood Floor (3)
75” x 45 1/2”
Exploded view of all parts necessary to
complete Floor Section. Identify all parts
prior to starting. Note, Floor Footprint is
136 1/2” deep x 141 1/2” wide.
Concrete Pad
(optional foundation method)
Front
Plywood Floor (3)
66 1/2” x 45 1/2”
Floor Frames(3)
66 1/2” x 45 1/2”
1. Lay out all Floor Joist Frames and Floor
Joists on ground as illustrated above. Position
72” Floor Joists in 75” frames and 63 1/2” Floor
Joists in 66 1/2” frames. Position Joists equally
in Floor Joist Frame. Position Joist so flush
with framing.
Flush
with
framing
Floor Runners (5)
3 1/2” x 60”
Floor Joists (6)
3 1/2” x 63 1/2”
Floor Joists (6)
3 1/2” x 72”
Parts (Steps 1 - 3)
Floor Joists - Large
(1 1/2” x 3 1/2” x 72”) x 6
Floor Joists - Small
(1 1/2” x 3 1/2” x 63 1/2”) x 6
Floor Joist Frames - Large
(45 1/2” x 75”) x 3
Floor Joist Frames - Small
(45 1/2” x 66 1/2”) x 3
Hardware (Steps 1 - 3)
S1 - 2 1/2” Screws
x 66 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 8

2. When correctly positioned, attach each Joist with 4 - 2 1/2” screws (2 per end).
Complete all Floor Frame and Joist connections. You can find the Square Drive Bit for the screws
in with the Hardware Kit Bag.
You can find the
Square Drive Bit
for the screws in
with the Hardware
Kit Bag.
4. Attach each completed section together with 16 - 2 1/2” screws as illus-
trated above.
Hardware (Step 4)
S1 - 2 1/2” Screws
x 32 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 9
3. Lay out one of each Floor Frames as shown above. Attach th 66 1/2” frame to the 75” with
6 - 2 1/2” screws (18 total).Complete 3 sets.
136 1/2”
141 1/2
Front Door
on this side

7. Position Plywood Floor pieces (6) on top
of completed Floor Joists. Plywood will sit
slightly back from edge of Floor Joist
Framing.
Parts (Steps 7 - 8)
Floor Plywood - Large
(5/8” x 45 1/2” x 75”) x 3
Floor Plywood - Small
(5/8” x 45 1/2” x 66 1/2”) x 3
Hardware (Steps 7 - 8)
S2 - 1 1/4” Screws
x 120 total
6. With some helpers, flip the floor section over so it rests on your foundation. Caution: you will need
2 people to assist you. Be careful when laying floor down not to bend or twist floor. When in place,
level floor completely.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 10
5. Attach Floor Runners to completed floor
frame. There are 2 floor runner pieces per 136
1/2” side and 5 completed runners in total. use
6 - 2 1/2” screws per runner.
Hardware (Step 5)
S1 - 2 1/2” Screws
x 32 total
Parts (Step 5)
Floor Runners - Long
(1 1/2” x 3 1/2” x 76 1/2”) x 5
Floor Plywood - Short
(1 1/2” x 3 1/2” x 60”) x 5
45 1/2”
66 1/2”
45 1/2”
75”

8. With Floor Plywood pieces in position, attach with 1 1/4” screws. Use screws every 16”
(approximately 90 total). The plywood is cut slightly smaller than floor framing. Keep plywood seams
tight.
Hint: Use a chalk
line to mark location
of floor joists to
determine screw
placement.
Important: Check to confirm that your
floor is level prior to proceeding to the
next step of wall assembly.
141 1/2”
182”
Front of Shed
B. Wall Section
Solid Wall Panels (9)
1 with 2 extra studs
Side Riser Plates (4)
Side Top Plates (6)
Gable Half Walls (4)
F&R Riser Plates (4)
F&R Top Plates (6)
Narrow Window
Wall Panel (2)
Door Jambs (2)
Door Header Riser (1)
Door Header w/ Spacers (1)
Drip Edge w/ Bevel Siding (1)
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 11

Important: Make sure all walls are
aligned in their upright position. If
not ,water may leak into your shed.
Unsure if panel is facing up or
down? check siding on window wall
panel to match alignment.
2x3 Plate of wall panel is
flush with floor frame. Siding
overhangs floor by 1/2”.
Side Wall Panel
Rear of Shed
Rear of Shed
Bottom Wall Plate
9. Starting with Solid Wall Panels, carefully lay
panel face down. Position and attach Wall Plate to
bottom of wall studs of each Wall Panel with
3 - 2 1/2” screws. Position so plates are flush with
framing. Note: Bottom Wall Plates may already be
attached to some Solid Walls.
Important:
Pilot hole ALL 2x3 Wall Studs
with 1/8” drill bit prior to screwing.
This will make it much easier to
attached together.
Pilot
Hole Plate
first.
Parts (Step 9)
Solid Wall Panels
(45 1/2” x 81 3/4”) x 9
Bottom Wall Plates
(1 1/2” x 2 1/2” x 45 1/2”) x 9
Hardware (Step 9)
S1 - 2 1/2” Screws
x 27 total
10. Starting at Rear Corner, position a Solid Wall
Panel on top of plywood floor. Make sure panel is
facing up. The Side Wall Panels will sit flush with
floor frame with the front and rear panels sandwiched
between them. Note: siding will overhang the floor
by approx. 1/2”.
Parts (Step 10)
Solid Wall Panels
(45 1/2” x 81 3/4”) x 9
Narrow Window Wall Panels
(34 3/4” x 81 3/4”) x 2
Hardware (Step 10)
S1 - 2 1/2” Screws
x 39 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 12

11. Position rear Wall Panel into place on plywood floor. Butt both vertical wall studs of side and rear
walls together and attach with 3 - 2 1/2” screws. Screw at the bottom, middle and top of stud to
secure properly.
Optional:
Small bead of
Caulk on wall
frame first.
Rear Window Wall
Side Solid Wall
12. With the corner wall attachment complete, position a Solid Rear Wall Panel so bottom 2x3 wall
framing is sitting flush with outside floor frame. Wall siding should overhang floor by approximately
1/2”. Attach rear wall panel studs together as per Step 11.
2x3 wall framing flush with
outside of floor frame.
13. With Position the final Rear Panel on the
floor (Window Wall Panel). Position vertical
wall studs together and attach as per Step 11.
Important: Do not
attach walls to floor
until Step 22.
Important: Rear
Center Solid Wall
Panel has 3 studs.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 13

14. Attach a Solid Wall Panel in corner. Attach as per Step 11. Start positioning and securing
remaining Solid Walls. Attach wall studs together as per Step 11.
Important: Pilot
hole studs first.
15. Complete attachment of left side Solid Wall Panels. At the front of the shed, side walls will sit
flush with front floor framing.
Wall panel will sit
flush with floor
framing at front of
shed.
16. Secure remaining two Narrow Window Walls to both front corners of shed.
Important: Remove the marked support block from
Narrow Window Walls before installation to reveal
notch for Door Header.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 14

17. Locate Vertical Door Jamb and position flush
against each wall panel stud. The Jamb is 3 1/2” wide
and will sit flush to outside of wall siding. When
positioned correctly, secure Jamb using 4 - 2 1/2”
screws.
Part (Step 17)
Vertical Door Jamb
(1 1/2” x 3 1/2” x 73”) x 2
Hardware (Step 17)
S1 - 2 1/2” Screws
x 8 total
Door Jamb sits
flush with wall
framing and tips
of bevel siding.
18. Position and attach Door Header Riser to
Door Jamb and Narrow Wall Panel top framing.
Header should fit flush with Door Jamb and
Outside of Narrow Wall Siding. Attach with
4 - 2 1/2” screws.
Part (Step 18)
Door Header Riser
(1 1/2” x 2 1/2” x 70”) x 1
Hardware (Step 18)
S1 - 2 1/2” Screws
x 4 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 15

19. Locate Door Header and Door Header
Spacers. Lineup three pieces together so they
are flush to creater a larger piece, attach with
6 - 2” screws.
Part (Step 19 - 20)
Door Header
(1 1/2” x 7 1/4” x 70”) x 1
Door Header Spacer
(1/2” x 7 1/4” x 70”) x 2
Hardware (Step 19 - 20)
S3 - 2” Screws
x 13 total
20. Place assembled Door Header onto Door Header Riser and attach with 7 - 2” screws.
21. Locate Drip Edge with Bevel Siding
attached. Attach to Door Header Spacer with
8 - 1 1/2” Finishing Nails.
Part (Step 21)
Drip Edge w/ Bevel Siding
(67”) x 1
Hardware (Step 21)
N1 - 1 1/2” Finishing
Nails
x 10 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 16

22. When all walls are attached
together, check alignment with the
floor. Bottom wall framing should
sit flush with outside of floor joists.
When positioned correctly, fasten
bottom wall plates to floor using
4 - 2 1/2” screws per wall panel
(48 total). Confirm 64” wide
door opening at bottom.
Bottom Wall
Framing
Important: If walls are not lining
up and appear higher or lower than
each other, please check the level
of your floor. You may need to
make slight adjustments before
proceeding.
Optional: Caulking seams will
help prevent moisture from
entering your shed. Caulking
is included to complete roof
only. Additional Caulking may
be required.
Caulking
Angle
screws into perimeter
Floor Joists.
64”
Advice: Prior to fastening walls and installing
rafters, take time to confirm your walls are
level, square and plumb.
Measure diagonal at top and bottom of walls
corner-to-corner. This should be approximately
189 3/8”. More importantly, if measurements
are not within 1/4”, your walls are not square.
Adjusting now will make it easier to the roof
section later.
189 3/8”
189 3/8”
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 17

23. Position and attach F & R Riser Plates on
top of Front and Rear Wall Frames. attach with
4 - 2 1/2” screws each. Complete both front and
rear of shed.
Parts (Steps 23)
F&R Riser Plates
(1 1/2” x 2 1/2” x 70 3/4”)
x 4
Hardware (Steps 23)
S1 - 2 1/2” Screws
x 16 total
24. Position and attach Side Riser Plates with
6 - 2” screws per piece. Complete both sides of
shed.
Parts (Steps 24)
Side Riser Plates
(1 1/2” x 2 1/2” x 65 3/4”)
x 4
Hardware (Steps 24)
S3 - 2” Screws
x 24 total
25. Position and attach Front & Rear Top
Plates.There are two pieces with angle cut ends
and one straight piece per side. Attach with
4 - 1 1/4” screws per piece. Complete Front and
Rear
Parts (Steps 25)
F&R Top Plates Angle
(3/4” x 2 1/2” x 45”) x 4
F&R Top Plates Straight
(3/4” x 2 1/2” x 51 1/2”) x 2
Hardware (Steps 25)
S2 - 1 1/4” Screws
x 24 total
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 18

26. Position and attach Side Top Plates on Side
Riser Plates. 35 3/4” side plates are on the outside
with the 60” plate in the center. Angle of Side Plates
should match angle of F&R Top Wall Plates. Attach
each piece with 4 - 1 1/4” screws. Complete both
sides of shed.
Parts (Steps 26)
Side Top Plates
(3/4” x 2 1/2” x 60”) x 2
(3/4” x 2 1/2” x 35 3/4”) x 4
Hardware (Steps 26)
S2 - 1 1/4” Screws
x 24 total
Top and Side
plates flush
27. Locate Triangular Gable Half Walls for
both sides of shed. Align framing and wall siding
lap together. Screw center wall framing of each
piece together with 4 - 2 1/2” screws. Note: Prior
to attaching, try each combination of Gables for
best fit.Tip of Gables are separate pieces that
need to be attached on in Step 28.
Parts (Steps 27-28)
Gable Half Walls x 4
Hardware (Steps 27-28)
S1 - 2 1/2” Screws
x 8 total
S3 - 2” Screws
x 8 total
Male / Female Gable
Siding Overlap
Gable End tucked inside
Gable.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 19