OLT CABANA CB128-SLIDER-CEDAR-BEV User manual

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 1
Important Information:
- It is the sole responsibility of the customer to check with your local municipal or county by-laws before
ordering this product to confirm it complies with building codes in your area.
- If the product is elevated, any structural and building code requirements are solely the customer's
responsibility, and should be abided by.
- Snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep
snow off roof frequently.
- In areas with high or gusty wind conditions, it is advisable to install the structure securely to the ground.
- Have a regular maintenance plan to ensure screws, doors, windows and parts are tightly affixed.
- All structures purchased from Outdoor Living Today are covered for a period of one year for defects in
manufacturing and workmanship. Costs incurred for customer installations are not included.
- Failure to use supplied parts included in this kit could result in poor product performance and may void
your warranty. Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from
our written instructions.
Thank you for purchasing a
12x8 Cabana. Please take
the time to identify all the
parts prior to assembly.
Version #1.0
September 28, 2023
In the event of a missing or broken piece, simply call the Outdoor Living Today Customer Support Line
@ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our commitment to you to courier
replacement parts, free of charge, within 10 business days of this notification. Replacement parts will not be
provided free of charge after the 30 day grace period.
Stock Code:
CB128-SLIDER-CEDAR-BEV
Customer agrees to hold Outdoor Living Today and any Authorized Dealers free of any liability for improper
installation, maintenance and repair.
12x8 CABANA SLIDER
WITH BEV SIDING & CEDAR
ROOF

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 2
What to do before my Shed arrives?
Become familiar with this assembly manual and determine if you can com•
plete the project yourself or will require a professional contractor.
Clear the construction area and ensure a clear pathway for delivery when•
the freight company arrives. Remove all debris: roots, grass, rocks, etc.
Excavate the site. Contact your local utilities company to ensure there are•
no gas or electric lines buried in the area before digging.
Decide on the type of foundation you will be using:•
 Concrete slab, or
 46 inches of crushed gravel with paver stones or 4x4 stringers.
You can find the footprint for your shed on Page 3 of your Assembly
Manual.
If doing the assembly yourself, have all the necessary tools ready to go and•
in working condition. A list of required tools can be found after the parts
list.
One helper is recommended to assist in constructing your chalet.•
It generally takes two people more than two days to assemble a chalet.
If you’re hiring a contractor, their rate should be in line with that duration
of work.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 3
Foundation Types for 8x12 Garden Shed
Concrete Slab Foundation:
- Slab must be at least the same size as assembled floor frame (136 1/2” x 96”) or larger.
- 6” Deep foundation.
- 1.7 Cubic Yards of concrete required.
- A concrete slab will have the longest durability out of your foundation options.
Once level, a concrete slab is the easiest surface to build on.
Gravel with 4x4 Pressure Treated Stringers:
- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 2.1 Cubic Yards of gravel required, approximately 19 wheelbarrows.
- 7 - 4x4 Pressure Treated Stringers 8’ long required.
- Evenly spaced, with one at each end of floor frame.
Saves money on materials, easy to level and work with.
Gravel with Patio Paver Stones:
- Excavate at least 6” deep, and 6” wider than floor frame on each side.
- 2.1 Cubic Yards of gravel required, approximately 19 wheelbarrows.
- 25 patio pavers (8” x 8” or larger).
- Center patio paver stones underneath floor runners and underneath seams in floor joists.
Patio paver stones are widely available from most landscape stores.
96”
136 1/2”
6” Deep
108”
148 1/2”
7 - 4”x4”x96”
25 Patio Stones
Floor FrameConcrete Foundation Completed Foundation
18 5/8”
Gravel Foundation Gravel Foundation with treated stringers Completed Foundation
Gravel Foundation Gravel Foundation with Patio Pavers Completed Foundation
96”
136 1/2”
108”
148 1/2”

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 4
Thank you for purchasing our 12x8 Cabana.
Please take the time to identify all the parts prior to assembly.
Note: Trim and Skirting pieces are graded with the best face being rough sawn.
Rough sawn cedar is much easier to paint and stain.
Parts List
A. Floor Section
Floors
3 - Floor Joist Frames - Large - 45 1/2” x 75”
3 - Floor Joist Frames - Small - 45 1/2” x 21”
6 - Center Floor Joists - Unattached
- 1 1/2” x 3 1/2” x 71 7/8”
2 - Front Floor Runners - 1 1/2” x 5 1/2” x 68 3/16”
8 - Floor Runners - 1 1/2” x 3 1/2” x 68 3/16”
3 - Plywood Floor - Large - 45 3/8” x 74 7/8”
3 - Plywood Floor - Small - 45 3/8” x 20 7/8”
Steps
1 - 11
B. Wall Section
Main Wall Panels
7 - Solid Wall Panels (Side & Rear) - 45 1/2” x 75”
2 - Front Wall Panels - 35” x 73”
7 - Bottom Wall Plates - 1 1/2” x 2 1/2” x 45 1/2”
2 - Bottom Wall Plates - 1 1/2” x 2 1/2” x 35”
Door Headers
2 - Door Header (Dado cut edge) - 2” x 3” x 26 1/4”
1 - Door Header (Dado cut edge, Metal Strip Attached)
- 2” x 3” x 84”
1 - Interior Door Header - 1 1/2” x 3” x 66 1/2”
Top Wall Plates & Gables
6 - Side Top Plates - 3/4” x 2 1/2” x 32”
(4 pieces angle cut on end, 2 piece straight cut both
ends)
4 - Front & Rear Top Plates (angle cut edge)
- 3/4” x 2 1/2” x 65 3/4”
4 - Gable Half Walls - Triangular Shaped
12 - 18
19 - 22
23 - 26
C. Rafter & Roof Section
Rafter Assembly
2 - Roof Ridge Boards - 3/4” x 4 1/2” x 84”
2 - Roof Ridge Boards - 3/4” x 4 1/2” x 52 1/2”
18 - Roof Rafters - 1 1/2” x 3 1/2” x 56 1/2”
4 - Soffits - 1” x 4 1/2” x 68 1/4”
3 - Roof Gussets (angle cut on ends) - 3/4” x 3 1/2” x 72”
Roof
4 - Outer Roof Panels - 51” x 59 1/4”
2 - Middle Roof Panels - 45 1/2” x 59 1/4”
16 - Filler Shingles - Long
4 - Filler Shingles - Short
22 - Cedar roof Ridge Caps (1 short Ridge Cap for center
of roof)
27 - 37
38 - 47
D. Trim / Misc. Section
Filler & Outer Trim
7 - Bottom Skirting Side & Rear (Bevel) -
1/2” x 4 1/2” x 45 1/4”
3 - Bottom Skirting Front - 1/2” x 4” x 43 1/2”
4 - Filler Trim - 3/4” x 2 1/2” x 75”
3 - Top Wall Trim (Bevel) - 1/2” x 1 1/2” x 45 1/4”
4 - Horizontal Gable Trim (Bevel) - 1/2” x 4 1/2” x 45 1/4”
Door & Track Section
2 - Aluminum Door Tracks
2 - Sliding Doors - 36” x 73”
2 - Lower Door Track - 1 1/2” x 1 5/8” x 60”
3 - Door Track Stops - 1 1/2” x 2 1/4” x 3 1/2”
3 - Lower Door Track Cover - 3/4” x 3 1/2” x 43 1/2”
1 - Interior Door Flange - 3/4” x 3 1/2” x 71 1/2”
Facia Trim
4 - Corner Trim - 1/2” x 3 1/2” x 79”
4 - Wide Corner Trim - 1/2” x 5 1/2” x 82”
2 - Rear Wall Narrow Trim - 1/2” x 2 1/2” x 79”
2 - Side Wall Narrow Trim - 1/2” x 2 1/2” x 77 1/2”
4 - Facia Nailing Strips - 3/4” x 2 1/2” x 51”
4 - Side Facia (Angle Cut, 2 right, 2 left)
- 3/4” x 5 1/2” x 58”
4 - Front and Rear Facia - 3/4” x 5 1/2” x 71 3/4”
2 - Pentagon Facia Plate - For Side Facia Peaks
2 - Horizontal Gable Trim Detail Plates - 4 1/2” high
2 - Facia Detail Plates - 3 1/2” high
Miscellaneous
2 - Metal Window Inserts
2 - Window Trim Pkgs - (1 - 24 1/16” angle cut / 3 - 23”
square cut)
1 - Spare Wall Siding
2 - Spare Shingles - use to shim door, etc
Steps
48 - 52
53 - 57
58 - 66
67 - 71
Note: We recommend you drill a 1/8” pilot hole for each
screw to avoid splitting wood. The hole depth should be
equal to 3/4 the length of screw.

Hardware Kit (Provided)
Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 5
Single
Rafter
Bracket x 6
Double Rafter
Bracket x 4
Ridge Board
Connector x 2
Black Hasp Roller Assembly x 4 90° Metal
Bracket
x 8
Tools Required (Not Provided)
Safety Equipment Required (Not Provided)
12x8 CABANA - CEDAR ROOF
Safety Glasses
Work Gloves
Ladder
Screw Gun/Drill Tape Measure
Hammer Wood Clamp
Level Pliers 1/8” & 3/8” Drill Bits
3/4”
1 1/2”
Door
Handle
x 2
Black Headed Screw
Finishing
Square Drive Bit
18 pcs
320 pcs
1 pc
2 1/2”
3/4”
Silver
1 1/4”
350 pcs
210 pcs
26 pcs
3” 30 pcs
1 1/2”
Shingle
60 Pcs
2” 150 pcs

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 6
Regular Maintenance & Tips to prolong the life of your shed.
Before/During Assembly:
1.) Paint each face and edge of your plywood floor with a latex exterior paint.
2.) Caulk wall seams if gaps appear.
3.) Caulk around window framing.
4.) Caulk perimeter between floor plywood and bottom wall plate.
5.) Caulk channels in lap siding at the top of your door above the trim, just a drop in each chan-
nel.
6.) Caulk edge of door threshold.
7.) Optional: Install a Sill Gasket between floor runners and foundation.
8.) Optional: Install an 8” strip of roofing paper below Cedar Ridge Caps for Cedar Roof Sheds.
Routine Maintenance:
- Routinely check all fasteners are tight (ex. Door Hinges, Nails)
- Brush off dirt from walls.
- Brush off snow from roof regularily.
- Routinely remove needles and leaves from Metal Roof.
Painting/Staining
- Your cedar shed, if left untreated, will weather to a silvery grey colour.
- Painting or staining your structure is highly recommended and will prolong the life of your shed.
- You do not need to wait to paint or stain your shed, the wood in your kit has been dried and can
be stained or painted immediately.
- Consult your local paint store for the best paint or stain for cedar.
- Optional: stain the inside of your shed. (Note: this will remove the fresh cedar smell.)
1. 2. 3.
4. 5. 6.
7.
Sill Gasket
Floor Joists
Foundation
8.
Floor Plywood
Wall Panel
Dab of caulking
Strip of roofing paper over
apex of roof panels
Floor Runner
Small gap
between bevel
siding and
window trim

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 7
You can find the Square Drive Bit for the screws in with the Hardware Kit Bag.
1. Lay out Large Floor Joist Frame and 2 Floor Joists as illustrated above. Position Joists equally
in Floor Joist Frame. Use Small Floor Joist Frame as a template to determine joist position. Position
Joist so flush with framing.
Parts (Steps 1 - 6)
Floor Joists
(1 1/2” x 3 1/2” x 71 7/8”) x 6
Floor Joist Frames - Large
(45 1/2” x 75”) x 3
Floor Joist Frames - Small
(45 1/2” x 21”) x 3
Hardware (Steps 1 - 6)
2 1/2” Screws
x 58 total
A. Floor Section
Exploded view of all parts necessary to complete Floor Section. Identify all parts prior to
starting. Note: Floor Footprint is 136 1/2” wide x 96” deep.
Flush
with
framing
Plywood Floor
Large (3)
Floor Joist
Frames
Large (3)
Floor Runners (8)
Plywood Floor
Small (3)
Concrete Pad
(optional foundation method)
Floor Joist
Frames
Small (3)
Floor Runners (2)

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 8
2. When correctly positioned, attach each Joist with 4 - 2 1/2” screws (2 per end). You can find
the Square Drive Screw Bit in the Hardware Kit Bag.
3. Lay out Floor Joist Frames as illustrated.
There are 3 larger and 3 smaller Frame Sections.
The Footprint for the floor when attached together
will be 136 1/2” wide x 96” deep.
5. Complete all large and small frame
attachments. Screw each completed section
together with 8 - 2 1/2” Screws.
Front of Shed
You can find the Square Drive Bit for the
screws in with the Hardware Kit Bag.
4. Attach each Large and Small Floor Joist
Frame together with 6 - 2 1/2” Screws per
section.
96”
136 1/2”
6. When completed, your floor footprint should
be 136 1/2” wide x 96” deep.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 9
7. Attach Front Floor Runners to completed floor frame with notch
aligned flush with corner of floor framing and edge overhanging front
by 2”. The overhanging edge of the Front Floor Runners will be used
later to support the sliding door track. Attach with 6 - 2 1/2” Screws
per Runner.
Parts
Front Floor Runners
(1 1/2” x 5 1/2” x 68 3/16”) x 2
Hardware
2 1/2” Screws x 12 total
9. With Floor Runners attached, carefully flip the floor over and place on your foundation.
Caution: you will need 2 people to assist you. Be careful when laying floor down not to bend or twist
floor. When in place, level floor completely.
Note: The floor will be flipped over
and the floor runners will sit on your
foundation. It is important to note that
having a level foundation is critical.
Choosing a foundation will vary
between regions.
See page 3 of this assembly manual
for more information on foundations.
Foundations
8. Attach Floor Runners to completed floor frame as shown
above. Make sure Runners are flush with side and rear of floor
framing but not overhanging. Use 6 - 2 1/2” Screws per Runner.
Parts
Floor Runners
(1 1/2” x 3 1/2” x 68 3/16”) x 8
Hardware
2 1/2” Screws x 48 total
Concrete Slab
Foundation

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 10
Front
10. Position all Large and Small Plywood Floor pieces on top of completed Floor Joists. Plywood
will sit flush with outside of Floor Joist Frame.
Parts (Steps 10 - 11)
Plywood Floor - Large
(45 3/8” x 74 7/8”) x 3
Plywood Floor - Small
(45 3/8” x 20 7/8”) x 3
Hardware (Steps 10 - 11)
1 1/4” Screws
x 70 total (approx.)
Important - Make sure floor is
level before moving on to wall
section. Use a level to confirm,
and shim floor joists as required.
11. With Plywood positioned correctly on floor framing, attach with 1 1/4” Screws. Use screws every
16” along the perimeter of each piece of Floor Plywood.
push plywood
together at seams.
Front
Completed Floor
configuration
Hint: Use a chalk
line to mark
location of floor
joists to determine
screw placement.

Gable Walls (4)
Front Wall Panel (2)
Solid Wall Panels (7)
Side Top Plates (6)
Bottom Wall
Plates (4)
Door Headers (3)
B. Wall Section
Exploded view of all parts necessary to complete the Wall Section. Identify all parts prior to
starting.
Important:
Pilot hole ALL 2x3 Wall
Studs with 1/8” drill bit prior
to screwing. This will make it
much easier to attach
together.
Pilot Hole
first.
Bottom Wall Plate
12. For each Solid Wall Panel/Front Wall Panel, carefully lay panel face down. Position and
attach Bottom Wall Plates to bottom of wall studs of each wall panel with 3 - 2 1/2” Screws.
Position so Plates are flush with framing.
Parts
Solid Wall Panels (45 1/2” x 75”) x 7
Bottom Wall Plates (1 1/2” x 2 1/2” x 45 1/2”) x 7
Front Wall Panels(35” x 73) x 2
Bottom Wall Plates (1 1/2” x 2 1/2” x 35”) x 2
Hardware
2 1/2” Screws
x 27 total
Front/Rear Top
Plates (4)
Interior Door Header (1)

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 12
Side of Shed
14. Starting at rear corner, position a Rear Solid Wall Panel on top of Plywood Floor. The Bottom
Wall Plate will sit flush with Plywood. Wall siding will overhang the Floor. The Rear Wall panels will sit
flush at the end of the Plywood Floor with the Side Wall panels sandwiched between them.
Note: Siding will overhang the Floor by approximately 1/2”.
Front of Shed
Important - Make sure all walls are aligned in their upright position. If not, water may leak into your
shed.
1st Rear Wall Panel
side of shed
13. Lay out all the Wall Panels and become familiar with their location. On Standard Kits, there are
7 Solid Wall Panels and 2 Front Wall Panels. Make sure to position panels right side up so water is
directed away from and not into shed. Look at door opening and exposed wide Floor Runner to
determine proper wall position to confirm.
1st Rear Solid
Wall Panel
1/2” overhang
Flush with
Floor Framing

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 13
Do Not Attach Walls To
Floor Until Step 22
Side Wall
Rear Wall
15. Position Side Solid Wall Panel into place on Plywood Floor. Butt both
vertical wall studs of side and rear walls together and attach with 3 - 2 1/2”
Screws. Screw at the bottom, middle and top of stud to secure properly.
Hardware (Steps 15 -17)
2 1/2” Screws
x 18 total
Rear Wall
Side Wall
16. With the corner wall attachment complete, position a second Side Solid Wall Panel in place so
bottom 2x3 wall framing is sitting flush with outside floor joists and Plywood Floor. Wall siding should
overhang floor by approximately 1/2”. When positioned correctly, attach both Side Wall panel studs
together as shown.
Pilot Hole
first.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 14
17. Complete all Side and Rear Wall attachments as per Steps 15 - 16. The rear wall is made up of
three Rear Solid Wall Panels.
Pilot Hole
first.
Pilot Hole
first.
Pilot Hole
first.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 15
Pilot Hole
first.
Pilot Hole
first.
18. Position and attach both Front Wall Panels
as per Steps 15 - 17.
Parts
Front Wall Panels
(35” x 73”) x 2
Hardware
2 1/2” Screws
x 6 total
19. Position Door Header - Short on top of
wall stud so it is flush on the inside with 2x3
wall stud. Attach by screwing down into top wall
framing with 3 - 3” Screws.
Parts (Step 19 - 20)
Door Headers - Short
(2” x 3 1/2” x 26 1/4”) x 2
Door Header - Long
(2” x 3 1/2” x 84”) x 1
Hardware (Step 19 - 20)
3” Screws
x 10 total
1 1/4” Screws
x 4 total
Step to front
and top.
Align flush
outside with
wall siding.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 16
20. Attach Door Header - Short to other side. Position and attach Door Header - Long between
Short Door Headers. The Long Door Header has an aluminum strip attached to the back for added
support. Attach by screwing down into wall framing with 2 - 3” Screws per side. Fasten aluminum
strip to Short Headers with 2 - 1 1/4” Screws per side.
Aluminum strip on back
of Long Door Header
21. Attach Interior Door Header as shown above. Align with top framing of front walls. Attach with
4 - 2 1/2” Screws.
Hardware
2 1/2” Screws
x 4 total
Parts
Interior Door Header
(1 1/2” x 3” x 66 1/2”) x 1
Advice: Use Interior Door Header
to confirm doorway opening is
66 1/2” wide at top and bottom.
66 1/2”

22. When all walls are attached together, check alignment with the floor.
Bottom of wall frames should sit flush with outside of floor framing, with siding
overhanging by approximately 1/2”. Confirm 66 1/2” wide door opening at
bottom. When positioned correctly, fasten Bottom Wall Plates to floor using
4 - 2 1/2” Screws per wall panel.
Hardware
2 1/2” Screws
x 36 total
23. Position Side Top Plates (one side only) on top of wall studs so they are flush on the inside.
There are 3 Side Top Plate pieces per side (2 angle cut on one end and one straight cut - both ends).
Together, the Plates should be centered evenly on the wall left to right. Attach by screwing down into
top wall framing with 3 - 2” Screws per Plate.
Parts (Steps 23 - 24)
Side Wall Top Plates - 4 Angle Cut End, 2 Straight Cut
(3/4” x 2 1/2” x 32”) x 6
Front & Rear Wall Top Plates - Angle Cut Edge
(3/4” x 2 1/2” x 65 3/4”) x 4
Hardware (Steps 23 - 24)
2” Screws
x 34 total
159 7/8”
159 7/8”
Angle
screws into perimeter
Floor Joists.
Pilot Hole
first.
66 1/2”
Advice: Prior to fastening walls and installing rafters, take time to confirm your walls are level, square and
plumb. Measure diagonal at top and bottom of walls corner-to-corner. This should be approximately 159 7/8”.
More importantly, if measurements are not within 1/4”, your walls are not square. Adjusting now will make it
easier to install roof section.
Optional - Caulking
seams will help prevent
moisture from entering
your shed. Caulking
not included in kit.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 18
24. Next, attach the Front Top Plates. The Front and Rear Top Plates are angle cut down the length.
Once again, position Top Plates on wall frame so they are flush. Front and Rear Top Plates will fit
between Side Top Plates. Attach with 4 - 2” Screws per plate. Complete all other Side & Rear Top
Plate attachments the same.
Male / Female Gable
Siding Overlap
25. Locate Triangular Gable Half Walls for both sides of the shed. Align framing and wall siding
lap together. Screw center wall framing of each piece together with 3 - 2 1/2” Screws.
Note: Prior to attaching, try each combination of Gables for best fit.
Parts
Triangular Gable Half Walls x 4
Hardware
2 1/2” Screws x 6 total

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 19
Flashing overhangs
wall on outside.
26. Place completed Gable section so framing sits flush with the inside of the Top Wall Plate.
It should also be centered side-to-side on the Top Wall Plate. Gable Flashing overhangs wall on the
outside. Temporarily attach to Gables and Top Wall Plate with 2 - 2” Screws. Gables may need slight
adjustment in Step 35 when attachment will be completed with an additional 6 Screws. Screw from
the bottom of Gable framing down into Top Wall Plate and Wall Framing. Complete Gable positioning
and attachment on the other side.
Hint: Use a straight edge to check the angle of the Gable framing and Top Plate. Both angles should
line up (see diagram above).
Hardware
2” Screws x 4 total
Use a straight edge to check that angle of
Gable lines up with Top Wall Plate angle.
Adjust Gable for best fit.

Outdoor Living Today www.outdoorlivingtoday.com [e-mail]
Page 20
Ridge Board
Ridge Board
Metal Ridge Board Connector
8 - 3/4” Screws
Parts
Ridge Board Long
(3/4” x 4 1/2” x 84”) x 2
Ridge Board Short
(3/4” x 4 1/2” x 52 1/2”) x 2
Hardware
3/4” Screws
x 16 total
27. Locate Ridge Boards Long & Ridge Boards Short and attach together with Metal Ridge
Board Connector using 8 - 3/4” silver screws. Position Metal Ridge Board Connector evenly on
Ridge Boards. Total length when connected is 136 1/2”. Complete two sets.
Roof Gussets (3)
Roof Rafters (18)
C. Rafter & Roof Section
Exploded view of all parts necessary to complete the Rafter and Roof Section. Identify all
parts prior to starting.
Outside Roof Panels (2)
Outside Roof
Panels (2)
Middle Roof Panels (2) Filler Shingles (20)
Metal Ridge Board
Connectors (2)
Soffits (4) Rafter Brackets Double (4)
Single (6)
Ridge Boards (4)
52 1/2” and
84” long