Omron E5CC-T User manual

最小60
45
45
+0.6
0
+0.6
0
+0.6
0
（48×台数 - 2.5）
+1.0
0
45
表示潜在的危险情况，如不加以防止，很可能导致轻
度或中度的人身伤害或财产损坏。在使用该产品前应
仔细阅读本手册。
E5CC-T
数字式控制器
安全使用注意事项
有关详细的应用步骤，请参阅《E5@C-T数字式控制器用户手册》
（Cat. No. H188）。
使用说明书
感谢您购买欧姆龙E5CC-T数字式控制器。
本手册描述了产品的功能、性能以及使产品达到最佳使用效
果的应用方法。
请在使用该产品时注意以下事项：
·使用该产品的人必须具备足够的电气系统知识。
·在使用该产品前应通读并理解本手册以确保正确的使用。
·妥善保管该手册以确保在需要时可以随时查阅。
欧姆龙公司
©All Rights Reserved
警告
CHN
安全注意事项
警告符号的要点
尺寸规格 安装 连接（端子适用性因机器型号而异。）
规格
接线
前面板的元件名称
·°C / °F：温度单位
根据温度单位的设定值显示C或F。
·模式键
按此键改变显示内容。
按该按钮1秒以上反方向显示内容。
•同时按住O键和M键并保持3秒钟以上即可切换
为保护菜单。
·菜单键
使用该键切换菜单。
·移位键（PF键）
按此键后，设定的功能即会按高级功能设定标准
的“PF设定”启动运行。PF设置参数默认设定为使
数位移位。
•:
当设定变更保护为ON（禁用向上/向下
键）时点亮。
操作菜单
•同时按住M键和D键并保持1秒钟以上即可在运行/
复位之间相互切换。
•默认的报警类型为“2”
*1: 要使参数1、4和5提供不同的报警类型，可对其设定上限与下限。下限和上限分
别用字母 L和H指示。
*2: 关于输入类型和报警类型的项目，请参考上面的表格。
*3: 只有参数“ins时：温度输入偏移”参数中的设定值应用于整个温度输入范围。
如果输入偏移值设定为1.2°C，则过程值为200°C时，经过输入偏移后按照
201.2°C处理。而如果输入偏移值设定为-1.2°C，则经过输入偏移后过程值按照
198.8°C处理。
*4: 当转至初始设定菜单时运行停止。
（控制/报警均停止。）
调整菜单
∗只在显示为“PV/SP”时出现错误显示，其它状态下不会出现。
■联系方式
●制造商
●技术咨询
欧姆龙(上海)有限公司
地址:中国（上海）自由贸易试验区金吉路789号
电话:[phone]
欧姆龙自动化(中国)有限公司
地址:中国上海市浦东新区银城中路200号中银大厦2211室
电话:[phone]
技术咨询热线:400-820-4535
网址:http://www.fa.omron.com.cn
当发生一个错误时，第一显示将显示错误代码。参考下表，根据错误代码采取适当的措施。
检查输入类型参数的设置，检查输入接线并检查温度传感器是否
存在破损或短接。
关掉电源再打开，如果显示不变，则须修理控制器。如果显示恢复
正常，则可能是控制系统受到外部干扰。检查外部干扰。
确认输入异常后，请重新接通电源。如果显示不变，则须修理控制
器。如果显示恢复正常，则故障原因可能是控制系统受到外部干
扰。请检查外部干扰。
第一显示 含义
A/D转换错误
*
内存错误
输入错误
*
s.err (S. Err)
e111 (E111)
操作
OFF
报警
出错状态
OFF
OFF
同上述上限
报警工作
OFF
OFF
e333 (E333)
错误显示（故障诊断）
控制输出
报警
* 根据型号和设定的不同，有些灰色的设定项目可能不显示。
如果输入值超出了显示范围（-1999～9999），即使仍然在控制范围内，低于-1999的数值也将显示为 [[[[ ，而
高于9999的数值将显示为 ]]]] 。在这种情况下，控制输出和报警输出均为正常工作状态。可控制范围详情请参
阅《E5□C-T数字式控制器用户手册》（Cat. No. H188）。
使用时的注意事项
在客户的应用中，欧姆龙不负责产品与任何客户端产品所涉及的规格、规范和标准
保持一致性。请务必考虑本产品对于所应用的系统、机器和设备间的适用性。使用
时请注意并遵守本产品的禁止事项。
在没有确认整个系统设计时所考虑到的风险，以及没有确认在设备和系统中该欧姆
龙产品的额定使用条件和正确安装条件的情况下，禁止将本产品应用于对人身及财
产存在严重危险的场合。
详见产品规格书中保证及免责事项内容。
警告
警告符号
通电期间，请勿触摸端子。
否则会因触电而导致轻伤。
不得让金属物体、导线或安装时产生的切屑或湿气进入控制器、调试工具端口或调试工具电缆连接
器的引脚上。否则会导致触电、火灾或机器误动作。
请勿将该产品用于有易燃易爆气体的场合。否则有可能因为爆炸而造成轻度伤害。
绝对不要拆卸、改装以及修理该产品或接触任何内部元件。否则会导致轻微触电、火灾或机器误动
作。
注意－火灾或触电的危险
a) 该产品为UL列表的开放型过程控制设备，必须安装在能够防止火花迸出的机壳中。
b) 在使用两个以上断电开关的情况下，维修前请先断开所有开关，确保本产品处于断电状态。
c) 信号输入为SELV（安全低压电源），回路受限。
d) 注意：为了减少火灾或触电的危险，请勿将不同的2类回路的输出互联。
如果输出继电器超过了预期的使用寿命，有时会发生触点熔化或燃烧。始终要注意输出继电器的应
用环境，并在额定负载及预期寿命以内使用。输出继电器的预期寿命随着输出负载以及开关条件的
变化而变化。
松动的螺丝可能导致火灾。请以指定的0.43～0.58 N·m的指定扭矩拧紧螺丝。
请设定适合系统控制用的产品参数。如果设定不当，可能会因意外操作而造成财产损失或事故。
控制器误动作很可能造成控制操作失效或阻止报警输出，导致财产损失。为了在控制器发生误动作
时确保安全，应采取适当的安全措施，如使用单独的线路安装监控设备。
供电电压
工作电压范围
功率消耗
指示精度
（环境温度：23°C）
事件输入
有接点输入
无接点输入
控制输出1
控制方法
辅助输出
转换输出
使用环境温度
使用环境湿度
存储温度
高度
推荐保险丝
重量
防护等级
安装环境
内存保护
暂时过电压
100～240 VAC，50/60 Hz或者
24 VAC，50/60 Hz/24 VDC
额定电压的85～110%
最大7.5 VA（100～240VAC）
最大4.1 VA（24VAC）/最大2.3 W（24VDC）
热电偶输入：
（显示值的±0.3%或者±1°C中的较大值）
最大±1位数
铂电阻输入：
（显示值的±0.2%或者±0.8°C中的较大值）
最大±1位数
模拟量输入：
±0.2 % FS 最大±1位数
输出电流：每个触点约7 mA。
ON：最大1 kΩ，OFF：最小100 kΩ
ON：残余电压最大1.5 V
OFF：漏电流最大0.1 mA
继电器输出：SPST-NO
250 VAC，3 A（阻性负载）
继电器电气寿命：100,000次运行
电压输出（用于驱动SSR）：
12 VDC±20%，21 mA
线性电流输出：4～20 mA DC，0～20mA DC
负载：最大500 Ω
2路PID控制
继电器输出：SPST-NO，250 VAC，
2 A（阻性负载）
继电器电气寿命：100,000次运行
4～20 mA DC，最大负载500 Ω
1～5 VDC，最小负载1 kΩ
-10～55°C
（应避免结冰或结露）
RH 25～85%
-25～65°C
（应避免结冰或结露）
最高2,000米
T2A，250 VAC，时延，低熔断容量
约120 g（仅数字控制器）
前面板：IP66
后壳：IP20，端子：IP00
安装种类II，
污染等级2（IEC61010-1）
非挥发内存
（写次数：1,000,000）
短时间过电压 1200V+（电源电压）
长时间过电压 250V+（电源电压）
请务必遵守以下注意事项，以避免操作失误、误动作或对产品特性及功能造成不良影响。否则，
可能会导致意外事故。请在指定范围内使用本产品。
(1) 该产品只被设计为室内使用。请勿在室外使用。请勿在以下任何地方使用或存放该产品。
· 直接受加热设备热辐射的地方。
· 有液体或油气飞溅的地方。
· 阳光直射的地方。
· 灰尘较多或有腐蚀性气体（特别是硫化物气体和氨气）的地方。
· 温度剧烈变化的地方。
· 结冰和结露的地方。
· 有震动或大的冲击的地方。
(2) 在额定的温度和湿度范围内使用 /存储该设备。必要时应采取强制冷却。
(3) 为利于散热，不要填塞该产品周围的空间。
不要堵塞产品的通风孔。
(4) 按端子的极性进行正确的接线。
(5) 请使用规定尺寸的压接端子（M3，宽度小于或等于 5.8 mm）进行接线。使用标有 AWG24
～AWG18（相当于横截面积 0.205～0.8231mm2）的铜绞线或实心电缆连接裸线和接线板。（剥
线长度为 6～8 mm。）一个端子内最多插入两根相同型号尺寸的导线或压接端子。
(6) 不用的端子不要接线。
(7) 在控制器与可以产生高频和浪涌的设备之间应保持足够远的距离。将高压或大电流电源线
与其它导线隔离，在端子接线时避免与电源线共端或并联。
(8) 在额定负载和供电电源下使用该产品。
(9) 使用开关或继电器触点以确保在两秒内将电源升为额定电压。如果电压是逐渐上升的，电
源可能无法复位或者发生输出误动作。
(10)
在接通电源到开始实际操作前应确保控制器进行30分钟以上的预热，以保证正确的温度显示。
(11) 在该产品的附近应该有开关或者断路器。开关或者断路器应该在操作者便于够到的地方，
并且有明显的断开标志。
(12) 清洁时，请用干的软布擦拭。请勿使用稀释剂、汽油、酒精等含溶剂的药品。否则会导致
变形或变色。
(13) 在设计系统（如控制面板）的时候，需要考虑到控制器的输出在电源上电后有2秒的延时。
(14) 当切换到初始设定菜单时，输出可能会关闭。在实施控制时需要考虑到这一点。
(15) 非挥发内存的写次数是有限的。所以在通信或其它操作需要频繁重写数据时，请使用 RAM
写模式。
(16) 拆卸控制器进行废弃处理时，请使用适当的工具。
(17) 请勿超过规格中给出的通信距离并使用指定的通信电缆。关于通信距离和电缆规格，请参
阅《E5□C-T 数字式控制器用户手册》（Cat. No. H188）。
(18) 连接了 USB 系列转换电缆时，请勿开、关控制器的电源。否则会导致控制器故障。
(19) 端子最高温度达 75℃，请多加小心。使用耐热在 75℃以上的导线连接端子。
stb
0.00
p
8.0
i
233
wt-b
off
ins
0.0
M
M
M
M
M
d
40
at
off
cmwt
off
spmd
psp
fsp
0
M
M
M
M
ol-h
100.0
ol-l
0.0
M
of-r
50.0
M
M
M
M
plcm
1234
M
ct1
0.0
hb1
0.0
M
M
恒定SP
积分时间
（单位：秒）
比例带
AT执行/取消
100%AT执行at-2
40%AT执行at-1
加热器电流值1监控
（单位：A）
加热器断线检测1
（单位：A）
微分时间
（单位：秒）
通信写入
SP模式
MV上限
MV下限
PV输入偏移量 *3
等待区间
待机时间
通信监控
调整菜单用于在控制时输入设定值和偏移值。
手动复位值
清除P或PD控制
期间的偏移量。
orl
0.0
MV变化率极限
运行停止
（控制/报警均停止。） *4
初始设定菜单
尺寸（mm）
E5CC-T默认设定为一K型热电偶（输入类型5）。
如果使用不同的传感器，则会发生输入错误（s.err）。
检查输入类型参数的设置。
通电之前检查接线。
*1
*1
*1
X
ON
OFF SP
X
ON
OFF SP
ON
OFF SP
X
X
ON
OFF SP
L H
ON
OFF SP
X
ON
OFF SP
X
ON
OFF SP
X
ON
OFF 0
ON
OFF X
0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF X
0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF X
0
ON
OFF X
0
ON
OFF X
0
ON
OFF X
0
L H
ON
OFF SP
SP
ON
OFF X
ON
OFF X
0
1
0
2
3
4
5
6
7
8
9
14
15
16
17
10
11
12
13
SP
X
ON
OFF
ON
OFF X
0
通电
输入类型 *2
比例缩放上限（仅限
设定模拟量输入时）
比例缩放下限（仅限
设定模拟量输入时）
小数点位置（仅限
设定模拟量输入时）
温度单位
SP上限
SP下限
in-t
5
in-h
100
in-l
0
dp
0
d-u
c
17
18 12
15
16
1
213 14
3
11
4
6
7
8
9
10
5
动作显示 6
4
5
65 6
Pt +
−
mA
−
+
5
4
传感器温度/模拟量输入
V
−5
V6
+
4
TC 4
I
（无极性）
11
12
输入电源
11
12
100～240 VAC 24 VAC/DC
(64)
85
604
144.8×44.8
辅助输出
辅助输出1、2、3
7
8
9
10
辅助输出2
辅助输出3
辅助输出1
+
+
−
16
17
18
13
16
17
18
13
14
15
18
16
17
065
事件输入1～4
064
通信（RS-485）和
事件输入3、4
13
066
事件输入1、2和转换
输出
选项
061
事件输入1、2和
CT1
V
I
14
15 14 15
EV1
EV2 EV1
EV2
EV3
EV4 EV3
EV4
B(+)
A(−)
RS-485
+−
3
1
2
3
1
2−
1个线性电流
1个继电器
3
控制输出1
1
2
1个电压
(SSR驱动专用)
+
RX QX CX
在包装内有：
·主单元
·使用说明书
·防水密封圈（Y92S-P8）：
·适配器（Y92F-49）：
另售件
·端子盖（E53-COV23）
·USB串行转换电缆
（E58-CIFQ2）
∗请勿拆下接线板。否则，会导致故障或误动作。
∗产品的上部备有调试工具端口。当需使用调试工具时，可通过该端口将个人计算机与本产品相连。连接个人计算机与产品需要
E58-CIFQ2 USB串行转换电缆。（使用该产品时不可一直连接USB串行转换电缆。）
详细的连接方法，请参照USB串行转换电缆附带的使用说明书。
·第一显示
过程值或设定数据类型
·第二显示
设定值、设定数据读出值或更改的输入值
·向上和向下键
每按一次U键，第二显示上的值将增大或显
示下一个值。
每按一次D键，第二显示上的值将减小或返
回上一个值。
•TUNE:
AT(自动调整)时亮灯。
•CMW:
当通信写允许时点亮，禁止时熄灭。
°C= c
°F= f
初始设定菜单可以使用户指定喜欢的工作条件（输入类型、报警类
型、等等）。
操作菜单
5377448-7A
M
M
M
M
M
M
M
∗ 为符合EMC标准，连接传感器的电缆不得长于30米。
如果电缆长度超过30米，则不符合EMC标准。
单独安装（mm） 紧密安装（mm）
·将主单元插入面板（1～5mm厚）的安装孔中。把安装支架（提供）插入后壳顶部和底部的
固定槽中。
·拧紧适配器顶部和底部的两颗安装螺丝使其保持平衡，最终使其扭矩保持在0.29至
0.39N·m之间。
·当安装多台机器时，请确保环境温度不超过规定限值。
紧密安装无法确保防水性能。
当有防水要求时，请在前面
板的后侧安装防水密封圈。
CQR

非焊接端子尺寸：M3
输出1输出1输出1
A
B
B
L H
ON
OFF
SP
控制输出1
继电器
250 VAC，3 A（阻性负载）
电压（用于驱动SSR）
12 VDC，21 mA
线性电流
0～20 mA DC
负载：最大500 Ω
4～20 mA DC
继电器
250 VAC，2 A
（阻性负载）
辅助输出
48×48
•SUB1～3：显示辅助输出1～3
• FSP:
恒定SP模式为开启状态时亮灯。
•OUT1：显示控制输出1
• RST:
程序复位中亮灯。
• MANU:
手动模式时亮灯。
• WAIT:
程序待机中亮灯。
pru
m
pvst
sp
tspu
0
M
M
M
M
M
M
M
alt1
2
alh1
0.2
M
M
M
传送输出类型
tr-t
off
传送输出上限
tr-h
100.0
传送输出下限
tr-l
0.0
事件输入分配1
事件输入分配2
事件输入分配3～4
转至高级功能
设定菜单
amov
0
传送输出信号
trst
4-20
M
M
M
M
ev-2
adv
ev-1
rr-1
M
M
ev-3
none
M
M
25
0
hold
off
ct1
0.0
pgsg
0.00
prg
0
a-m
r-r
rst
25
0
M
25
0
M
M
M
M
M
seg
0
M
M
stbm
0.00
prgt
0.00
M
M
rptm
0
M
M
styp
ramp
sp
0
M
pr
0
M
time
0.00
M
rpt
0
link
end
M
M
M
pid
1
M
M M
d.seg
end
U
Eend 0～7时
s-no
8
M
M
7
6
5
4
3
2
1
d.prg
0
D
7
6
5
4
3
2
1
d.seg
0
al1l
0
M
al-1
0
al1h
0
M
M
of1
0.00
M
ts1s
0
on1
0.00
M
M
25
0
U
D
U
D
d.pid
1
M
有关高级功能设定菜单、手动控制菜单以及其它功能的详细信息，请参阅《E5□C-T
数字式控制器用户手册》（Cat. No. H188）。有关通信的详细信息，请参阅《E5□
C-T数字式控制器通信手册》（Cat. No. H189）。
其它功能
保护菜单
PV/SP (1)
连接的传感器与
输入类型不同时，
显示s.err。
PV/SP (2)
连接的传感器与
输入类型不同时，
显示s.err。
自动/手动切换
仅限PID 控制
按住O和
M键至少
1秒
按住O和M
键至少3秒
PID设定菜单
按O（不超过1秒） 按O（不超过1秒）
按O
（不超过1秒）
按O
（不超过1秒）
按住O至少1秒
（第一显示闪烁，然后控制停止。）
按住O至少3秒
*2
报警1～4类型
报警1～4滞后
程序时间单位
时间设定/斜坡设定
斜坡时间设定单位
复位操作
通电后的操作
运行结束时的操作
PV开始
程序编号
已过程序时间监控
程序执行重复监控
剩余待机时间监控
分段 编号
暂停
程序No.监控/
分段No.监控
加热器电流值
1监控
（单位：A）
(程序的)
运行/复位
PID设定编号
报警值
1～4
报警上限
1～4
报警下限
1～4
使用的分段编号
显示程序选项
分段n格式
(仅限斜坡设定时)
分段n SP
分段n时间
时间信号1～2
设定分段
时间信号1～2
ON时间
时间信号1～2
OFF时间
在此菜单中，输入程序的
SP和时间。
有关其它信息， 请参阅
《E5@C-T数字式控制器用户手册》
（Cat. No. H188）。
操作时应正常使用操作菜单。
程序链接
目标
程序
重复
控制输出1
信号
选择显示的PID
t-u
h-m
t-pr
time
rtsm
stop
p-on
cont
eset
rst
控制输出 选项
E5CC T M
CCT5
13
14
15
16
17
18
EV1
EV2
CT1
所有PID组AT上限SP
转换输出
请勿在灰色端子上连接任何器件。
对比例缩放采用下列范围：-1999～9999、
-199.9～999.9、-19.99～99.99、-1.999～
9.999
电流输入
电压输入
模拟量输入
类型
4～20mA
0～20mA
1～5V
0～5V
0～10V
25
26
27
28
29
设定范围
输入类型 输入
Pt100
JPt100
热电偶 K
J
T
E
L
U
N
R
S
B
W
PL II
设定
10～70°C
60～120°C
115～165°C
140～260°C
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
输入类型
-200～850
-199.9～500.0
0.0～100.0
-199.9～500.0
0.0～100.0
-200～1300
-20.0～500.0
-100～850
-20.0～400.0
-200～400
-199.9～400.0
-200～600
-100～850
-200～400
-199.9～400.0
-200～1300
0～1700
0～1700
100～1800
0～2300
0～1300
0～90
0～120
0～165
0～260
-300～1500
-199.9～900.0
0.0～210.0
-199.9～900.0
0.0～210.0
-300～2300
0.0～900.0
-100～1500
0.0～750.0
-300～700
-199.9～700.0
-300～1100
-100～1500
-300～700
-199.9～700.0
-300～2300
0～3000
0～3000
300～3200
0～3200
0～2300
0～190
0～240
0～320
0 ～500
铂电阻
温度计
∗默认值是“5”。
∗当输入类型不是铂电阻而错误的将铂电阻接入时，将会显示s.err。为了清除s.err
显示，需要正确接线并重新上电。
°C °F
红外温度
传感器
ES1B
温度输入
报警类型
根据L、H值
的不同而不同
根据L、H值
的不同而不同
根据L、H值
的不同而不同
无报警功能 无输出
绝对值上限
绝对值下限
LBA（仅对报警1）
偏差上/下范围
偏差上限
偏差上/下限
偏差下限
报警输出功能
正报警值（X）
负报警值（X）
设定
PV变化率报警
SP绝对值上限
SP绝对值下限
MV绝对值上限
MV绝对值下限
偏差上/下限待机序列ON
偏差上限待机序列ON
偏差下限待机序列ON
绝对值上限待机序列ON
绝对值下限待机序列ON
o1st
4-20
sl-h
1300
M
sl-l
-200
操作菜单的
PV/SP(1)(2)
分段n斜坡
(仅限斜坡设定时)
显示分段选项，
END或0到分段编号−1
在U程序SP模式
下1秒钟以上
由于UL认证要求，请使用带有出厂接线（内部接线）的E54-CT1L或
E54-CT3L电流互感器。
使用经UL认证的UL类别XOBA或XOBA7电流互感器进行现场接线（外部接
线），而非出厂接线（内部接线）。
在使用本产品时，请务必外接说明书上推荐的保险丝。
如果产品未按本公司指定的方法使用，那么产品具备的保护功能很
可能损坏。
在输入电源、 继电器输出之间以及其它端子之间提供了强化
绝缘。
符合安全标准
关于模拟输入
•
输入电压或电流时，请按照本产品的输入类别设定输入类型。
• 请勿将本产品用来测定“测量范畴为 II 、 III 、 IV ”的回路。
•
请勿将本成品用来测定“印加电压超过30Vrms或60VDC”的对象。
符合EN/IEC标准
这是一种A类产品。
因其在住宅区中会导致无线电干扰， 所以要求用户采取适当的措施
减少干扰。
程序设定菜单
线性电流输出时，0%输出以外
均亮灯。
A 급 기기 (업무용 방송통신기자재)
이 기기는 업무용(A 급) 전자파적합기기로서 판매자또는 사용자는 이 점을
주의하시기 바라며, 가정외의지역에서 사용하는 것을 목적으로 합니다.
控制周期（加热）
（单位：秒）
∗电压输出
（用于驱动SSR）：2
cp
20
M
orev
or-r
正向/反向运行
反向运行（加热）中
= or-r
正向运行（冷却）中
= or-d
M
oapt
0
pmsk
on
icpt
1
wtpt
off
pfpt
off
M
M
M
M
M
操作/调整保护
初始设定/
通信保护
设定改变保护
PF键保护
参数屏蔽有效
限制可以显示或改变的设定类型以及通过按键操作
进行的更改。
(−)
(−)
(−) (−)
(−)
∗ 对事件输入使用无电压输入。
无触点输入的极性在括号中给出。
如果将辅助输出1,2和3连接到不同的电位，
请在使用前检查COM端子的单一故障情况。

60 min.
45
45
+0.6
0
+0.6
0
+0.6
0
(48 x number of units - 2.5)+1.0
0
45
Indicates a potentially hazardous situation which, if
not avoided, is likely to result in minor or moderate
injury or property damage. Read this manual
carefully before using the product.
E5CC-T
Digital Controller
Be sure to observe the following precautions to prevent operation failure, malfunction, or adverse effects on the
performance and functions of the product. Not doing so may occasionally result in unexpected events.
Use the product within specifications.
(1) The product is designed for indoor use only. Do not use the product outdoors. Do not use or store the product
in any of the following locations.
•Places directly subject to heat radiated from heating equipment.
•Places subject to splashing liquid or oil atmosphere.
•Places subject to direct sunlight.
•Places subject to dust or corrosive gas (in particular, sulfide gas and ammonia gas).
•Places subject to intense temperature change.
•Places subject to icing and condensation.
•Places subject to vibration and large shocks.
(2) Use/store within the rated temperature and humidity ranges. Provide forced-cooling if required.
(3) To allow heat to escape, do not block the area around the product.
Do not block the ventilation holes on the product.
(4) Be sure to wire properly with correct polarity of terminals.
(5) Use the specified size of crimped terminals (M3, width 5.8 mm or less) for wiring. To connect bare wires to the
terminal block, use copper braided or solid wires with a gage of AWG24 to AWG18 (equal to cross- sectional
area of 0.205 to 0.8231 mm2). (The stripping length is 6 to 8 mm.) Up to two wires of same size and type, or
two crimped terminals can be inserted into a single terminal.
(6) Do not wire the terminals which are not used.
(7) Allow as much space as possible between the controller and devices that generate a powerful high- frequency
or surge. Separate the high-voltage or large-current power lines from other lines, and avoid parallel or
common wiring with the power lines when you are wiring to the terminals.
(8) Use this product within the rated load and power supply.
(9) Make sure that the rated voltage is attained within two seconds of turning ON the power using a switch or relay
contact. If the voltage is applied gradually, the power may not be reset or output malfunctions may occur.
(10) Make sure that the Digital Controller has 30 minutes or more to warm up after turning ON the power before
starting actual control operations to ensure the correct temperature display.
(11) A switch or circuit breaker should be provided close to this unit. The switch or circuit breaker should be within
easy reach of the operator, and must be marked as a disconnecting means for this unit.
(12) Wipe off any dirt from the Digital Controller with a soft dry cloth. Never use thinners, benzine, alcohol, or any
cleaners that contain these or other organic solvents. Deformation or discoloration may occur.
(13) Design system (control panel, etc) considering the 2 second of delay that the controller’s output to be set after
power ON.
(14) The output will turn OFF when you move to the Initial Setting Level. Take this into consideration when
performing control.
(15) The number of non-volatile memory write operations is limited. Therefore, use RAM write mode when
frequently overwriting data during communications or other operations.
(16) When disassembling the Temperature Controller for disposal, use suitable tools.
(17) Do not exceed the communications distance that is given in the specifications and use the specified
communications cable. Refer to the E5@C-T Digital Controllers User’s Manual (Cat. No. H185) for the
communications distance and cable specifications.
(18) Do not turn the power supply to the Digital Controller ON or OFF while the USB-Serial Conversion Cable is
connected. The Digital Controller may malfunction.
(19) The terminals can reach temperatures of up to 75°C. Use wires with heat resistance of 75°C min to wire the
terminals.
Precautions for Safe Use
Refer to the E5@C-T Digital Controllers User’s Manual (Cat. No. H185) for
detailed application procedures.
INSTRUCTION MANUAL
Thank you for purchasing the OMRON E5CC-T Digital Controller.
This manual describes the functions, performance, and
application methods needed for optimum use of the product.
Please observe the following items when using the product.
• This product is designed for use by qualified personnel with
a knowledge of electrical systems.
•Before using the product, thoroughly read and understand
this manual to ensure correct use.
•Keep this manual in a safe location so that it is available for
reference whenever required.
OMRON Corporation
©All Rights Reserved
Power supply voltage 100 to 240 VAC, 50/60 Hz or
24 VAC, 50/60 Hz / 24 VDC
Operating voltage range 85 to 110% of the rated voltage
Power consumption 7.5 VA max. (100 to 240 VAC)
4.1 VA max. (24 VAC)/2.3 W max. (24 VDC)
Indication accuracy Thermocouple:
(Ambient temperature: 23°C) (±0.3 % of indication value or ±1°C,
whichever is greater) ±1 digit max.
Platinum resistance thermometer:
(±0.2 % of indication value or ±0.8°C,
whichever is greater) ±1 digit max.
Analog input:
±0.2 % FS ±1 digit max.
Event input Output current: approx. 7 mA per contact.
Contact input ON:1 kΩ max., OFF: 100 kΩ min.
No-contact input ON: residual voltage 1.5 V max.,
OFF: leakage current 0.1 mA max.
Control output 1 Relay output :SPST-NO
250VAC, 3A(resistive load)
Electrical life of relay: 100,000 operations
Voltage output (for driving SSR):
12 VDC ±20%, 21 mA
Linear current output: 4 to 20 mA DC, 0 to 20mADC
Load: 500Ω max.
Control method 2-PID control
Auxiliary outputs Relay outputs:SPST-NO, 250 VAC,
2 A (resistive load),
Electrical life of relay: 100,000 operations
Transfer output 4 to 20 mA DC with load of 500 Ω max.
1 to 5 VDC with load of 1 kΩ min.
Ambient temperature -10 to 55°C (Avoid freezing or condensation)
Ambient humidity 25 to 85%
Storage temperature -25 to 65°C (Avoid freezing or condensation)
Altitude Max. 2,000m
Recommended fuse
T2A, 250 VAC, time-lag, low-breaking capacity
Weight Approx. 120 g (Digital Controller only)
Degree of protection Front panel: IP66
Rear case: IP20, Terminal section: IP00
Installation environment Installation categoryII, pollution
degree 2 (as per IEC61010-1)
Memory protection Non-volatile memory
(Number of write operations: 1,000,000)
Temporary overvoltage Short term: 1200 V+ power supply voltage
Long term: 250 V+ power supply voltage
CAUTION
CAUTION
Minor injury due to electric shock may occasionally occur.
Do not touch the terminals while power is being supplied.
Electric shock, fire, or malfunction may occasionally occur. Do not allow metal objects, conductors,
cuttings from installation work, or moisture to enter the Digital Controller, the Setup Tool ports, or
between the pins on the connectors on the Setup Tool cable.
Do not use the product where subject to flammable or explosive gas. Otherwise, minor injury from
explosion may occasionally occur.
Never disassemble, modify, or repair the product or touch any of the internal parts. Minor electric
shock, fire, or malfunction may occasionally occur.
CAUTION - Risk of Fire and Electric Shock
a) This product is UL listed as OpenType Process Control Equipment. It must be mounted in an enclosure that
does not allow fire to escape externally.
b) More than one disconnect switch may be required to de-energize the equipment before servicing.
c) Signal inputs are SELV, limited energy.
d) Caution: To reduce the risk of fire or electric shock, do not interconnect the outputs of different Class 2 circuits.
If the output relays are used past their life expectancy, contact fusing or burning may occasionally occur.
Always consider the application conditions and use the output relays within their rated load and
electrical life expectancy. The life expectancy of output relays varies considerably with the output load
and switching conditions.
Loose screws may occasionally result in fire. Tighten the terminal screws to the specified torque of 0.43
to 0.58 N•m.
Set the parameters of the product so that they are suitable for the system being controlled. If they are
not suitable, unexpected operation may occasionally result in property damage or accidents.
Amalfunction in the Digital Controller may occasionally make control operations impossible or prevent
alarm outputs, resulting in property damage. To maintain safety in the event of malfunction of the Digital
Controller, take appropriate safety measures, such as installing a monitoring device on a separate line.
EN
Safety Precautions
Key to Warning Symbols
Dimensions
When an error has occurred, the No.1 display shows the error code. Take necessary measure
according to the error code, referring the table below.
Check the setting of the Input Type parameter, check the input wiring,
and check for broken or shorts in the temperature sensor.
Turn the power OFF then back ON again. If the display remains the same, the
controller must be repaired. If the display is restored to normal, then a probable
cause can be external noise affecting the control system. Check for external noise.
After the check of Input error, turn the power OFF then back ON again. If
the display remains the same, the controller must be repaired. If the display
is restored to normal, then a probable cause can be external noise affecting
the control system. Check for external noise.
No.1 display Meaning
A/D converter error
*
Memory error
Input error
*
s.err (S. Err)
e111 (E111)
Action
OFF
Alarm
Control
output
Status at error
OFF
OFF
Operates as above
the upper limit.
OFF
OFF
e333 (E333)
Error Display (troubleshooting)
Warning Symbols
Installation Connections (The applicability of the electric terminals varies with the type of machine.)
Specifications
Wiring
Names of Parts on Front Panel
•°C / °F : temperature unit
Either Cor Fis displayed when the displayed value
is a temperature.
•Mode key
Press this key to move across the items within the setting level.
Press this button for 1 second or longer for reverse scroll.
•Hold the Okey and the Mkey together for at least 3
seconds to switch to protect level.
•Level key
Use this key to change levels.
•Shift key (PF key)
Pressing this key operates the function that has been set
on "PF Setting" of the advanced function setting level.
The default PF Setting parameter is for shifting the digit.
•:
Lit when Setting Change Protect is
ON (disables the Up and Down Keys).
Operation Menu
Alarms
OMRON EUROPE B.V.
Wegalaan 67-69, NL-2132 JD Hoofddorp The Netherlands
Phone [phone]
FAX [phone]
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg, IL 60173-5302 U.S.A
Phone [phone]
FAX [phone]
OMRON ASIAPACIFIC PTE. LTD.
No. 438AAlexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Phone [phone]
FAX [phone]
OMRON Corporation
Shiokoji Horikawa, Shimogyo-ku, Kyoto 600-8530 JAPAN
•Hold the Mkey and the Dkey together for at least 1
second to switch Run/Reset.
•The default alarm type is "2".
*1: Upper and lower limits can be set for parameters 1, 4 and 5 to provide for
different types of alarm. These are indicated by the letter "L" and "H".
*2: Refer to the tables above for details of input types and alarm types.
*3: Only the value set to the ins: Temperature Input Shift parameter is applied to the
entire temperature input range. When the process value is 200°C, the process value is
treated as 201.2°C after input shift if the input shift value is set to 1.2°C. The process
value is treated as 198.8°C after input shift if the input shift value is set to -1.2°C.
*4: Operation is stopped when moved to the initial setting level.
(control/alarm are both stopped.)
* The grayed-out setting items are not displayed for some models and some
settings of other setting items.
Adjustment Level
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide
applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This
information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the
end product, machine, system, or other application or use. Buyer shall be solely responsible for determining
appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take
application responsibility in all cases.
NEVER USE THE PRODUCT FORAN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY
WITHOUT ENSURING THAT THE SYSTEM ASA WHOLE HAS BEEN DESIGNED TOADDRESS THE RISKS, AND
THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Suitability for Use
* Error shown only for "Process value / Set point". Not shown for other status.
If the input value exceeds the display limit (-1999 to 9999), though it is within the control range, [[[[ will be displayed
under -1999 and ]]]] above 9999. Under these conditions, control output and alarm output will operate normally. Refer
to the E5@C-T Digital Controllers User’s Manual (Cat. No. H185) for the controllable ranges.
stb
0.00
p
8.0
i
233
wt-b
off
ins
0.0
M
M
M
M
M
d
40
M
at
off
cmwt
off
spmd
psp
fsp
0
M
M
M
M
ol-h
100.0
ol-l
0.0
of-r
50.0
M
M
M
plcm
1234
M
ct1
0.0
hb1
0.0
M
M
Communications Writing
SP Mode
AT Execute / Cancel
100%AT Execute at-2
40%AT Execute at-1
Heater Current 1
Value Monitor
(Unit: A)
Heater Burnout
Detection 1
(Unit: A)
Fixed SP
PV
Input Shift *3
Wait Band
Integral Time
(Unit: Seconds)
Proportional
Band
Standby Time
Derivative Time
(Unit: Seconds)
Adjustment level is for entering set values and shift values for control.
Manual Reset Value
Clears the offset
during P or PD control.
MV Upper Limit
MV Lower Limit
Communications
Monitor
orl
0.0
M
MV Change
Rate Limit
Operation stopped.
(Control/alarm are both stopped.)
*4
Initial Setting Level
Use the following ranges for scaling: -1999
to 9999, -199.9 to 999.9, -19.99 to 99.99,
-1.999 to 9.999
Analog
input type
Current input
Voltage input
Do not connect anything to the terminals that are shaded gray.
Dimensions (mm)
The E5CC-T is set for a K thermocouple (input type
of 5) by default. If a different sensor is used, an input
error (s.err) will occur.
Check the setting of the Input Type parameter.
Check the wiring before turning ON the power supply.
*1
*1
*1
Alarm type
Vary with
"L", "H" values
Vary with
"L", "H" values
Vary with
"L", "H" values
No alarm function Output off
Deviation upper/lower limit
standby sequence ON
Absolute value upper limit
Absolute value lower limit
Absolute value upper limit
standby sequence ON
Absolute value lower limit
standby sequence ON
LBA (only for alarm 1)
Deviation lower limit
standby sequence ON
Deviation upper limit
standby sequence ON
Deviation upper/lower range
Deviation upper limit
Deviation upper/lower limit
Deviation lower limit
Alarm output function
Positive alarm value (X) Negative alarm value (X)
Setting
PV Change Rate Alarm
X
ON
OFF SP
X
ON
OFF SP
ON
OFF SP
X
X
ON
OFF SP
L H
ON
OFF SP
X
ON
OFF SP
X
ON
OFF SP
X
ON
OFF 0
ON
OFF X
0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF X
0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF X
0
ON
OFF X
0
ON
OFF X
0
ON
OFF X
0
L H
ON
OFF SP
SP
ON
OFF X
ON
OFF X
0
1
0
2
3
4
5
6
7
8
9
SP absolute value upper limit
SP absolute value lower limit
14
15
MV absolute value upper limit
MV absolute value lower limit
16
17
10
11
12
13
SP
X
ON
OFF
ON
OFF X
0
POWER ON
Input Type *2
Scaling Upper Limit
(only when setting
analog input)
Scaling Lower Limit
(only when setting
analog input)
Decimal Point
(only when setting
analog input)
Temperature
Unit
SP Upper Limit
SP Lower Limit
in-t
5
in-h
100
in-l
0
dp
0
d-u
c
sl-h
1300
4 to 20mA
0 to 20mA
1 to 5V
0 to 5V
0 to 10V
25
26
27
28
29
Setting range
Input type Input
Pt100
JPt100
Thermocouple
Infrared
Thermosensor
ES1B
K
J
T
E
L
U
N
R
S
B
W
PL II
Setting
10 to 70°C
60 to 120°C
115 to 165°C
140 to 260°C
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
17
18 12
15
16
1
213 14
3
11
4
6
7
8
9
10
5
Operation indicators 6
4
5
65 6
Pt +
−
mA
−
+
5
4
Sensor Temperature/Analog Input V
−5
V6
+
4
TC 4
I
(no polarity)
11
12
Input Power Supply
11
12
100 to 240 VAC 24 VAC/DC
(64)
85
604
144.8×44.8
Auxiliary Outputs
Auxiliary outputs 1, 2,
and 3
7
8
9
10
Auxiliary output 2
Auxiliary output 3
Auxiliary output 1
+
+
−
16
17
18
13
16
17
18
13
14
15
18
16
17
065
Event inputs 1 to 4
064
Communications (RS-485)
and event inputs 3 and 4
13
066
Event inputs 1 and 2, and
transfer output
Options
061
Event inputs 1 and 2,
and CT1
V
I
14
15 14 15
EV1
EV2 EV1
EV2
EV3
EV4 EV3
EV4
B(+)
A(−)
RS-485
+−
3
1
2
3
1
2−
One linear
current
One relay
3
Control Output 1
1
2
One voltage
(for driving SSR)
+
RX QX CX
Sold Separately
*Terminal cover (E53-COV23)
*USB-Serial Conversion Cable
(E58-CIFQ2)
In the pack:
*Main unit
*Instruction manual
*Watertight packing (Y92S-P8): 
*Adapter (Y92F-49): 
* Do not remove the terminal block. Doing so may result in failure or malfunction.
* A Setup Tool port is provided on the upper of the product. Use this port to connect a personal computer to the product when using
the Setup Tool. E58-CIFQ2 USB-Serial Conversion Cable is required to connect the personal computer to the product. (Do not use
the product with the USB-Serial Conversion Cable left permanently connected.)
Refer to the instruction manual provided with the USB-Serial Conversion Cable for details on connection methods.
•No.1 display
Process value or set data type
•No.2 display
Set point, set data read-out value or changed input
value
• Up and Down keys
Each press of Ukey increments or advances the
values displayed on the No.2 display.
Each press of Dkey decrements or returns the
values displayed on the No.2 display.
•TUNE:
Lit during AT (auto-tuning).
•CMW:
Lit when communications writing is
enabled and not lit when it is disabled.
Input Type
-200 to 850
-199.9 to 500.0
0.0 to 100.0
-199.9 to 500.0
0.0 to 100.0
-200 to 1300
-20.0 to 500.0
-100 to 850
-20.0 to 400.0
-200 to 400
-199.9 to 400.0
-200 to 600
-100 to 850
-200 to 400
-199.9 to 400.0
-200 to 1300
0 to 1700
0 to 1700
100 to 1800
0 to 2300
0 to 1300
0 to 90
0 to 120
0 to 165
0 to 260
-300 to 1500
-199.9 to 900.0
0.0 to 210.0
-199.9 to 900.0
0.0 to 210.0
-300 to 2300
0.0 to 900.0
-100 to 1500
0.0 to 750.0
-300 to 700
-199.9 to 700.0
-300 to 1100
-100 to 1500
-300 to 700
-199.9 to 700.0
-300 to 2300
0 to 3000
0 to 3000
300 to 3200
0 to 3200
0 to 2300
0 to 190
0 to 240
0 to 320
0 to 500
Platinum
resistance
thermometer
Temperature inputs
*The default is“5”.
* s.err will be displayed when a platinum resistance thermometer is mistakenly connected while
input type is not set for it. To clear the s.err display, correct the wiring and cycle the power supply.
°C= c
°F= f
Initial setting level enables users to specify their preferred
operating conditions (input type, alarm type, etc.)
Operation Level
M
M
M
M
M
M
M
* When complying with EMC standards,
the line connecting the sensor must be
30 m or less. If the cable length exceeds
30 m, compliance with EMC standards
will not be possible.
Individual mounting (mm) Side-by-side mounting (mm)
• Insert the main unit through the mounting hole in the panel (1 to 5 mm thickness). Insert the
mounting brackets (supplied) into the fixing slots located on the top and bottom of the rear
case.
• Tighten the two mounting screws on the top and bottom of the adapter to keep them
balanced, and finally tighten them to a torque of between 0.29 and 0.39 N·m.
• When more than one machine is installed, make sure that the ambient temperature does
not exceed the specified limit.
Waterproofing is impossible
with side-by-side
installation. When
waterproofing is required, fit
watertight packing on the
backside of front panel.
°C °F
CQR

Solderless terminal size: M3
OUT1 OUT1 OUT1
A
B
B
Conformance to EN/IEC Standards
This is a class A product. In residential areas it may cause radio
interference, in which case the user may be required to take
adequate measures to reduce interference.
L H
ON
OFF
SP
Control output 1
Relay
250 VAC, 3 A (resistive load)
Voltage (for driving SSR)
12 VDC, 21 mA
Linear current
0 to 20 mA DC
Load: 500 Ω max.
4 to 20 mA DC
Relay
250 VAC: 2 A
(resistive load)
48×48
• SUB1 to 3: Auxiliary outputs 1 to
3 indicators
• FSP:
Lit when the Fixed SP mode is
ON.
• OUT1: Control output 1 indicator
Lit for other than 0% output for
linear current output.
• RST:
Lit during a program reset.
• MANU:
Lit during Manual Mode.
• WAIT:
Lit during a program wait.
pru
m
pvst
sp
tspu
0
M
M
M
M
M
M
M
Control Period (Heating)
(Unit: Seconds)
*Voltage output
(for driving SSR): 2
cp
20
M
alt1
2
alh1
0.2
M
M
M
Transfer
Output Type
tr-t
off
Transfer Output
Upper Limit
tr-h
100.0
Transfer Output
Lower Limit
tr-l
0.0
Event Input
Assignment 1
Event Input
Assignment 2
Event Input
Assignments 3 to 4
Move to Advanced
Function Setting
Level
amov
0
Transfer Output
Signal Type
trst
4-20
M
M
M
M
ev-2
adv
ev-1
rr-1
M
M
ev-3
none
M
M
25
0
hold
off
ct1
0.0
pgsg
0.00
prg
0
a-m
r-r
rst
25
0
M
25
0
M
M
M
M
M
M
seg
0
M
M
stbm
0.00
prgt
0.00
M
M
rptm
0
M
styp
ramp
sp
0
M
pr
0
M
time
0.00
M
rpt
0
link
end
M
M
M
pid
1
M
M M
d.seg
end
U
Eend 0 to 7
s-no
8
M
M
7
6
5
4
3
2
1
d.prg
0
D
7
6
5
4
3
2
1
d.seg
0
al1l
0
M
al-1
0
al1h
0
M
M
of1
0.00
M
ts1s
0
on1
0.00
M
M
25
0
U
D
U
D
d.pid
1
M
Refer to the E5@C-T Digital Controllers User’s Manual (Cat. No. H185) for
information on the Advanced Function Setting Level, Manual Control Level, and
other functions.
Refer to the E5@C-T Digital Controllers Communications Manual (Cat. No. H186)
for information on communications.
Other functions
Protect Level
s.err is displayed when
connected sensor is
different from input type.
Process Value/
Set Point (1)
Process Value/
Set Point (2)
s.err is displayed when
connected sensor is
different from input type.
Auto/Manual Switch
PID control only.
Hold Oand
Mkeys down
for at least 1
second
Hold Oand Mkeys
down for at least
3 seconds
Program Setting Level
PID Setting Level
Press O
(less than 1 second) Press O (less than 1 second)
Press O(less than 1 second) Press O(less than 1 second)
Hold Odown for
at least 1 second
(No.1 display flashes, then the control stops.)
Hold Odown for at least 3 seconds
*2
Alarms 1 to 4 Type
Alarms 1 to 4
Hysteresis
Program Time Unit
Step Time/Rate of
Rise Programming
Time Unit of Ramp Rate
Reset Operation
Startup Operation
Operation End
Operation
PV Start
Program Number
Elapsed Program
Time Monitor
Program Execution
Repetition Monitor
Remaining Standby
Time Monitor
Segment Number
Hold
Program No. Monitor/
Segment No. Monitor
Heater Current 1
Value Monitor
(Unit: A)
Run/Reset
(of the program)
PID Set
No.
Alarm
Values 1 to 4
Alarm
Upper
Limits 1 to 4
Alarm
Lower
Limits 1 to 4
Number of
Segments Used
Display Program
Selection
Display Segment Selection,
END or 0 to Number of
Segments − 1
Segment
n Format
(Only at
Slope Setting)
Segment
n SP
Segment n Slope
(Only at Slope
Setting)
Segment
n Time
Time Signals 1 to 2
Set Segment
Time Signals 1 to 2
ON Time
Time Signals 1 to 2
OFF Time
In this level, the SPs and times
are input for the programs.
For other information, refer to the E5@C-T
Digital Controllers User’s Manual
(Cat. No. H185).
Operation level should normally
be used during operations.
Program
Link
Destination
Program
Repetitions
Control Output
1 Signal
Press Ufor at least 1 sec.
in Program SP Mode
Display PID Selection
t-u
h-m
t-pr
time
rtsm
stop
p-on
cont
eset
rst
Control outputs Options
E5CC T M
13
14
15
16
17
18
EV1
EV2
CT1
All PID AT Upper
Limit SP
Transfer output
Conformance to Safety Standard
Reinforced insulation is provided between input power
supply, relay outputs, and between other terminals.
Due to UL Listing requirements, use the E54-CT1Lor E54-CT3L
current transformer with the factory wiring (internal wiring).
Use a UL category XOBAor XOBA7 current transformer that is UL
Listed for field wiring (external wiring) and not the factory wiring
(internal wiring).
Always externally connect the recommended fuse that is specified
in the Instruction Manual before you use the Digital Controller.
Analog Input
•
If you input an analog voltage or current, set the Input Type
parameter to the correct input type.
•Do not use the Digital Controller to measure a circuit with
Measurement Category II, III, or IV.
•
Do not use the Digital Controller to measure an energized circuit to
which a voltage that exceeds 30 Vrms or 60 VDC is applied.
The protection provided by the Digital Controller may be impaired if the
Digital Controller is used in a manner that is not specified by the
manufacturer.
sl-l
-200
Auxiliary outputs
o1st
4-20
PV/SP (1) (2) of
Operation
Level
orev
or-r
In Direct operation (Cooling)
= or-d
In Reverse operation (Heating)
=
or-r
Direct/Reverse Operation
M
Restricts which settings can be displayed or
changed, and restricts change by key operation.
oapt
0
pmsk
on
icpt
1
wtpt
off
pfpt
off
M
M
M
M
M
Operation /
Adjustment
Protect
Initial Setting /
Communication
Protect
Setting Change
Protect
Parameter Mask
Enable
PF Key Protect
* Use non-voltage inputs for the event inputs.
The polarity for a non-contact input is
indicated by “(-).”
(−)
(−)
(−)(−)
(−)
(−)
＊Check for a single-fault
condition of the COM
terminal before use if
auxiliary outputs 1,2 and
3 will be connected to
different electrical
potentials.