Omron THERMAC NEO Series Instruction manual

1
OMRON Corporation
Temperature Controller
CompoWay/F Driver
1 System Configuration....................................................................................................... 3
2 Selection of External Device ............................................................................................ 7
3 Example of Communication Setting ................................................................................. 8
4 Setup Items ....................................................................................................................18
5 Cable Diagram ............................................................................................................... 23
6 Supported device ........................................................................................................... 38
7 Device Code and Address Code.................................................................................... 45
8 Error Messages.............................................................................................................. 47

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 2
Introduction
This manual describes how to connect the Display and the External Device (target Temperature Controller).
In this manual, the connection procedure will be described by following the below sections:
1System Configuration
This section shows the types of the
External Device and SIO type.
)"1 System Configuration" (page 3)
2Selection of External Device
Select a model (series) of the External
Device to be connected and connection
method.
)"2 Selection of External Device" (page 7)
3Example of Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
)"3 Example of Communication Setting" (page
8)
4Setup Items
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in offline mode.
)"4 Setup Items" (page 18)
5Cable Diagram
This section shows cables and adapters
for connecting the Display and the
External Device.
)"5 Cable Diagram" (page 23)
Operation

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of OMRON Corporation and the Display are
connected is shown.
Connection Configuration
• 1:1 Connections
• 1:n Connection
Series CPU*1
*1 Model number of the controller "" varies depending on the function specification of each controller.
Link I/F SIO Type
Communi-
cation
Settings
Cable
Diagram
THERMAC
NEO
E5EN--FLK
E5AN--FLK
Terminal block
on the
controller
RS232C
Setting
Example 1
(page 8)
Cable
Diagram 1
(page 24)
E5EN--FLK
E5AN--FLK
E5CN--FLK
E5GN--FLK
RS485
(2wire)
Setting
Example 2
(page 10)
Cable
Diagram 2
(page 26)
THERMAC
R
E5AR--FLK
E5ER--FLK
Terminal block
on the
controller
RS485
(2wire)
Setting
Example 3
(page 12)
Cable
Diagram 2
(page 26)
In-Panel
NEO E5ZN--FLK
Terminal block
on the
controller
RS485
(2wire) 1:1
Setting
Example 4
(page 14) Cable
Diagram 2
(page 26)
RS485
(2wire) 1:n
Setting
Example 5
(page 16)
Display
External Drive
Display
External
Drive
External
Drive
External
Drive
Maximum number of connections: 16 units

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 4
IPC COM Port
When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please
refer to the IPC manual for details.
Usable port
Series
Usable Port
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
PS-2000B COM1*1 , COM2,
COM3*1, COM4
*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.
--
PS-3450A, PS-3451A,
PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2
PS-3650A (T41 model),
PS-3651A (T41 model) COM1*1 --
PS-3650A (T42 model),
PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2
PS-3700A (Pentium®4-M)
PS-3710A
COM1*1, COM2*1,
COM3*2 , COM4
*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.
COM3*2 COM3*2
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
PS4000*3
*3 When making communication between an External Device and COM port on the Expansion slot,
only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the
specification of COM port.
For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.
Please refer to the IPC manual for details of pin layout.
COM1, COM2 - -
PL3000 COM1*1*2, COM2*1,
COM3, COM4 COM1*1*2 COM1*1*2
PE-4000B Atom N270 COM1, COM2 - -
PE-4000B Atom N2600 COM1, COM2 COM3*4 , COM4*4,
COM5*4, COM6*4
*4 Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.
COM3*4, COM4*4,
COM5*4, COM6*4
PS5000 (Slim Panel Type
Core i3 Model) *5 *6 COM1, COM2*4 COM2*4 COM2*4
PS5000 (Slim Panel Type
Atom Model)
*5 *6
COM1, COM2*7 COM2*7 COM2*7
PS5000 (Enclosed Panel
Type)*8 COM1 - -
PS5000 (Modular Type
PFXPU/PFXPP)*5 *6
PS5000 (Modular Type
PFXPL2B5-6)
COM1*7 COM1*7 COM1*7
PS5000 (Modular Type
PFXPL2B1-4) COM1, COM2*7 COM2*7 COM2*7

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 5
DIP Switch settings (PL3000 / PS3000 Series)
RS-232C
*5 When setting up communication between an External Device and the RS-232C/422/485 interface
module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using
PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+
and 8.CTS+, and connect 6.RTS- and 9.CTS-.
When using RS-422/485 communication with External Devices, you may need to reduce the
transmission speed and increase the TX Wait time.
*6 To use RS-422/485 communication on the RS-232C/422/485 interface module, the DIP Switch
setting is required. Please refer to "Knowledge Base" (FAQs) on the support site. (http://www.pro-
face.com/trans/en/manual/1001.html)
*7 Set up the SIO type with the DIP Switch. Please refer to the IPC manual for details of DIP Switch.
The BOX Atom has not a switch to set the RS-232C, RS-422/485 mode. Use the BIOS for the
setting.
*8 For the connection with the External Device, on the user-created cable read as if the connector on
the Display-side is a M12 A-coding 8 pin socket. The pin assignment is the same as described in
the cable diagram. For the M12 A-coding connector, use PFXZPSCNM122.
DIP Switch Setting Description
1OFF
*1
*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.
Reserved (always OFF)
2OFF
SIO type: RS-232C
3OFF
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
Settings FAQ ID
PFXZPBMPR42P2, RS422/485 change method FA263858
PFXZPBMPR42P2 termination resistor setting FA263974
PFXZPBMPR44P2, RS422/485 change method FA264087
PFXZPBMPR44P2 termination resistor setting FA264088

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 6
RS-422/485 (4 wire)
RS-422/485 (2 wire)
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available
8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available
9OFF
RS (RTS) Auto control mode: Disabled
10 OFF
DIP Switch Setting Description
1 OFF Reserved (always OFF)
2ON
SIO type: RS-422/485
3ON
4 OFF Output mode of SD (TXD) data: Always output
5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None
6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None
7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available
8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available
9ON
RS (RTS) Auto control mode: Enabled
10 ON

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 7
2 Selection of External Device
Select the External Device to be connected to the Display.
Setup Items Setup Description
Number of Devices/
PLCs Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the display.
Manufacturer Select the manufacturer of the External Device to connect. Select "OMRON Corporation".
Series
Select the External Device model (series) and the connection method. Select "Temp. Controller
CompoWay/F".
In System configuration, make sure the External Device you are connecting is supported by
"Temp. Controller CompoWay/F".
)"1 System Configuration" (page 3)
Port Select the Display port to connect to the External Device.
Use System Area Cannot be set in this driver.

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 8
3 Example of Communication Setting
Examples of communication settings of the Display and the External Device, recommended by Digital
Electronics Corp., are shown.
3.1 Setting Example 1
Setting of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 9
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
Settings of External Device
Use the level key, mode key, down key and up key in front of the Temperature Controller for communication
settings of the External Device.
Please refer to the manual of the Temperature Controller for more details.
Procedure
1. Press and hold the level key (3 minutes or more) to transfer from the operation level to the default level.
2. Press the level key again to transfer from the default level to the communication setting level.
3. Press the mode key to select the parameter.
4. Press the down/up keys to change the setting.
5. Press and hold the level key to transfer to the operation level.
Setting Value
• Set the HOST link unit No. for "Unit No.".
PSEL CWF
U-NO 1
BPS 9.6
LEN 7
SBIT 2
PRTY EVEN
SDWT 2
• Parameters to be set vary depending on the Temperature Controller. Please refer to the manual of
the Temperature Controller for more details.
• Set Wait to Send to 2ms or more. Adjust Wait to Send according to the communication status.

Temperature Controller CompoWay/F Driver
GP-Pro EX Device/PLC Connection Manual 10
3.2 Setting Example 2
Setting of GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].