Omron MicroHAWK V/F3 F Series User manual

Z435-E-01 (84-9320017-02)
Installation Guide
MicroHAWK Optics and Lighting
Accessory Kit

MicroHAWK Optics and Lighting Accessory Kit
Installation Guide
This guide contains instructions for how to install the optical accessories on a MicroHAWK ID/MV-20,
V/F320-F, V/F330-F, V/F420-F and V/F430-F.
Contents
1. MicroHAWK ID/MV-20 Diffuser and Polarizer Kit Installation
2. MicroHAWK V/F3XX-F Diffuser and Polarizer Kit Installation
3. MicroHAWK V/F4XX-F Window and LED Kit Installation
4. MicroHAWK V/F4XX-F With Ring Light Window and LED Kit Installation
5. MicroHAWK V/F4XX-F Polarizer Kit Installation
MicroHAWK Optics and Lighting Accessory List
Type Description Kit Part Number
ID/MV-20
Window Kits
Kit, Diffuser, MicroHAWK ID/MV-20 98-9000077-01
Kit, Polarizer, MicroHAWK ID/MV-20 98-9000062-01
V/F330-F
and
V/F320-F Window
Kits
Kit, Diffuser, MicroHAWK V/F330 V330-AF1
Kit, Polarizer, MicroHAWK V/F330 V330-AF2
V/F430-F
and
V/F420-F
Window Kits
Kit, Window, V/F4XX V430-AF0
Kit, Diffuser, V/F4XX V430-AF1
Kit, Polarizer, V/F4XX V430-AF2
Kit, YAG Filter, V/F4XX V430-AF4
Kit, ESD Window, V/F4XX V430-AF5
Kit, Red Filter, V/F4XX V430-AF6
Kit, Blue Filter, V/F4XX V430-AF7
V/F430-F
and
V/F420-F
LED Kits
Kit, Red LED, V/F4XX V430-ALR
Kit, White LED, V/F4XX V430-ALW
Kit, Blue LED, V/F4XX V430-ALB
Kit, IR LED, V/F4XX V430-ALI
V/F430-F
With Ring Light
Window Kits
Kit, Window, RING LT, F/V430 V430-AF0R
Kit, Diffuser, RING LT, F/V430 V430-AF1R
Kit, Polarizer, RING LT, F/V430 V430-AF2R
V/F430-F
With Ring Light
LED Kits
Kit, Red LED, RING LT, F/V430 V430-ALRR
Kit, White LED, RING LT, F/V430 V430-ALWR
Kit, Blue LED, RING LT, F/V430 V430-ALBR
Kit, IR LED, RING LT, F/V430 V430-ALIR

MicroHAWK ID/MV-20 Diffuser and Polarizer Installation
Diffuser Kit Hardware, MicroHAWK ID/MV-20
Qty Description Kit Part Number
1 Kit, Diffuser, MicroHAWK ID/MV-20 98-9000077-01
Diffuser Kit Installation, MicroHAWK ID-20/MV-20
Step 1: Peel the protective liner from the adhesive on the diffuser.
Step 2: Rest the narrow edge of the diffuser on the bottom edge of the window opening at an angle as
shown below.
Step 3: Center the diffuser left-to-right in the window opening.
Step 4: Affix the diffuser to the window.
Step 5: Run your finger over the surface of the diffuser using light pressure to complete the bond.

Polarizer Kit Hardware, MicroHAWK ID-20/MV-20
Qty Description Kit Part Number
1 Kit, Polarizer, MicroHAWK ID/MV-20 98-9000062-01
Polarizer Kit Installation, MicroHAWK ID-20/MV-20
Step 1: Peel the protective liner from adhesive on the polarizer.
Step 2: Rest the narrow edge of the polarizer on the bottom edge of the window opening at an angle as
shown below.
Step 3: Center the polarizer left-to-right in the window opening.
Step 4: Affix the polarizer to the window.
Step 5: Run your finger over the surface of the polarizer using light pressure to complete the bond.

MicroHAWK V/F320 and V/F330 Diffuser and Polarizer Installation
Diffuser Kit Hardware, MicroHAWK V/F330 and V/F320
Qty Description Kit Part Number
1 Kit, Diffuser, MicroHAWK V/F330 V330-AF1
Diffuser Kit Installation, MicroHAWK V/F330 and V/F320
Step 1: Follow same steps as above for the ID/MV-20
Note: Take care to align the Diffuser so that the narrow edge is at bottom, that there is an equal gap
laterally, and that the bottom edge is aligned with bottom edge of window.
.
Polarizer Kit Hardware, MicroHAWK V/F330-F and V/F320-F
Qty Description Kit Part Number
1 Kit, Polarizer, MicroHAWK V/F330 V330-AF2
Polarizer Kit Installation, MicroHAWK V/F330 and V/F320
Step 1: Follow same steps as above for the ID/MV-20
Note: Take care to align the Polarizer so that the narrow edge is at bottom, that there is an equal gap
laterally, and that the bottom edge is aligned with bottom edge of window.

MicroHAWK V/F4XX-F Window and LED Kit Installation
Window Kit Hardware, MicroHAWK V/F430-F and V/F420-F
Qty Description Kit Part Number
1 Window, Diffuser, Polarizer or Filter Kits
(included)
V430-AF0 (Window)
V430-AF1 (Diffuser)
V430-AF2 (Polarizer)
V430-AF4 (YAG Filter)
V430-AF5 (ESD Window)
V430-AF6 (Red Filter)
V430-AF7 (Blue Filter)
4 0-80 Phillips-Head Screws (included)
1 Gasket (included)
1 Phillips Torque Wrench (not included) N/A
LED Kit Hardware, MicroHAWK V/F430-F and V/F420-F
Qty Description Kit Part Number
1 LED Board Kits (included) V430-ALR (Red LEDS)
V430-ALW (White LEDs)
V430-ALB (Blue LEDs)
V430-ALI (IR LEDs)
4 0-80 Phillips-Head Screws (included)
1 Gasket (included)
1 Phillips Torque Wrench (not included) N/A
1 Fine-Tip Tweezers (not included) N/A
Window Removal, MicroHAWK V/F4XX-F
Step 1: Disconnect power from the camera.
Step 2: Remove the four screws from the front window of the camera.
Step 3: Remove the front window and gasket.
Note: If installing a window accessory only, skip to Step 8.

Outer LED Removal, MicroHAWK V/F4XX-F
Note: If installing an LED accessory only, skip to Step 6.
Step 4: Remove the two screws from the LED boards.
Step 5: Unplug the LED boards from the camera.
Note: The LED boards have a connector interface. Gently pry the top of each LED board from the main
board using fine-tipped tweezers or an equivalent tool. Use caution not to contact the LEDs as they may
become damaged.
Outer LED Installation, MicroHAWK V/F4XX-F
Step 6: Plug the LED boards into the main board. Use caution not to touch the LEDs, as they may be
damaged by contact.
Step 7: Secure the LED boards in place using the screws provided. Do not over-tighten the screws.
(1.0 in./lbs. (0.11 nm max.)

Window Installation, MicroHAWK V/F4XX-F
Step 8: Install the gasket onto the camera. Ensure that the gasket is properly seated in place and is
covering all sealing surfaces.
Step 9: Install the window (or window accessory) onto the camera.
Step 10: Secure the window in place using the screws provided. Do not over-tighten the screws.
(1.0 in./lbs. (0.11 nm max.)

MicroHAWK V/F430-F with Ring Light Window and LED
Installation
Window Kit Hardware, MicroHAWK V/F430-F with Ring Light
Qty Description Part Number
1 Window Assembly (included) V430-AF0R (Window)
V430-AF1R (Diffuser)
1 Window Gasket (included)
2 #2-56 X 3/8” Phillips Flat Head Screw (included)
4 #4-40 X 1/4” Phillips Pan Head Screw w/ Lock
Washers (included)
1 Phillips Torque Wrench (not included) N/A
LED Kit Hardware, MicroHAWK V/F430-F with Ring Light
Qty Description Part Number
1 LED Board Kits (included) V430-ALR (Red LEDs)
V430-ALW (White LEDs)
V430-ALB (Blue LEDs)
V430-ALI (IR LEDs)
1 Window Gasket (included)
2 #2-56 X 3/8” Phillips Flat Head Screw (included)
4 #4-40 X 1/4” Phillips Pan Head Screw w/ Lock
Washers (included)
1 Phillips Torque Wrench (not included) N/A
Window Removal, MicroHAWK V/F430-F with Ring Light
Step 1: Disconnect power from the camera.
Step 2: Unscrew the four #4-40 pan head screws that secure the window.
Step 3: Remove the gasket from around the window frame.
Step 4: If not replacing the LED Board, go to step 8. If replacing the LED Board, unscrew the two #2-56
flat head screws that secure the diffuser.
Note: Do not touch the electronics or lens, as this may cause damage.

Outer LED Removal, MicroHAWK V/F430-F Ring Light
Step 5: Unplug the LED board from the camera.
Note: The LED board has two connectors on the left and right of the camera front face. Gently pry the
LED board from the camera using fine-tipped tweezers or an equivalent tool. Use caution not to contact
the LEDs as they may become damaged.
Outer LED Installation, MicroHAWK V/F430-F with Ring Light
Step 6: Plug the new LED board into the camera connectors. Use caution not to touch the LEDs, as they
may be damaged by contact.