Omron STC-MBS1242POE Installation instructions

No.18S052-02
1/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
GigE Vision
Monochrome / Color CMOS PoE Camera
STC-MBS1242POE (12M / Monochrome)
STC-MCS1242POE (12M / Color)
Product Specifications and User’s Guide

No.18S052-02
2/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
Table of Contents
1Product Precautions ............................................................................................ 8
2Warranty................................................................................................................ 8
3Software Licensing .............................................................................................. 9
3.1 LWIP TCP/IP Licensing ............................................................................................................9
4Introduction ........................................................................................................ 10
4.1 Features .................................................................................................................................. 10
4.2 Naming Method ...................................................................................................................... 10
5Specifications......................................................................................................11
5.1 Electronic Specifications....................................................................................................... 11
5.2 Spectral Sensitivity Characteristics ..................................................................................... 13
STC-MBS1242POE .......................................................................................................................... 13
STC-MCS1242POE (without IR Cut Filter) ..................................................................................... 13
IR Cut Filter (STC-MCS1242POE)................................................................................................... 14
5.3 Mechanical Specifications..................................................................................................... 14
5.4 Environmental Specifications ............................................................................................... 15
6Connector Specifications .................................................................................. 16
6.1 RJ45 Connector...................................................................................................................... 16
6.2 Power and Control Signal Connector................................................................................... 17
Opto-isolated input ......................................................................................................................... 20
Opto-isolated output....................................................................................................................... 20
Open Collector GPIO ...................................................................................................................... 21
Input and Output Signal Timing (Hardware Trigger)..................................................................... 22
Input and Output Signal Timing (Software Trigger)...................................................................... 23
External Hardware Trigger Input Delay.......................................................................................... 24
6.2.6.1 External Trigger Signal Delay (Positive polarity trigger signal)................................................ 24
6.2.6.2 External Trigger Signal Delay (Negative polarity trigger signal) .............................................. 24
6.2.6.3 Measured External Trigger Signal Delay through Opt-Isolated Port (Line 0)........................... 25
6.2.6.4 Measured External Trigger Signal Delay through Open Collector GPIO Port (Line 2) ............ 26

No.18S052-02
3/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
7Dimensions......................................................................................................... 27
7.1 STC-MBS1242POE ................................................................................................................. 27
7.2 STC-MCS1242POE ................................................................................................................. 28
8Sensor Information ............................................................................................ 29
8.1 Pixel Transferring Image........................................................................................................ 29
9Camera Operational Modes............................................................................... 30
9.1 Normal Mode (Rolling shutter) .............................................................................................. 30
9.2 Pulse width trigger mode....................................................................................................... 31
Timing (when using rolling shutter) .............................................................................................. 31
Exposure Timing with Positive Polarity Trigger Signal................................................................ 32
Exposure Timing with Negative Polarity Trigger Signal............................................................... 33
9.3 Edge Preset Trigger Mode ..................................................................................................... 34
Timing (When using rolling shutter).............................................................................................. 34
Exposure Timing with Positive Polarity Trigger Signal................................................................ 35
Exposure Timing with the Negative Polarity Trigger signal......................................................... 35
9.4 Edge Preset Trigger Mode (Trigger input while image is out) ............................................ 36
Timing.............................................................................................................................................. 36
10 Camera Functions.............................................................................................. 37
10.1 Save and load the camera settings.................................................................................... 37
Saving Camera Settings.............................................................................................................. 37
Loading Camera Settings............................................................................................................ 38
Loading Camera Settings when Camera Power is on ............................................................... 38
Camera Settings Initialization ..................................................................................................... 38
10.2 Frame rate ............................................................................................................................ 39
10.3 Gain ...................................................................................................................................... 39
Analog Gain ................................................................................................................................. 39
Digital Gain................................................................................................................................... 39
10.4 Exposure Time..................................................................................................................... 40
10.5 Black Level........................................................................................................................... 40
10.6 ALC (Auto Light Control) .................................................................................................... 41

No.18S052-02
4/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
ALC control method .................................................................................................................... 42
AGC (Auto Gain Contorl)............................................................................................................. 43
Auto shutter ................................................................................................................................. 44
ALC settings procedure .............................................................................................................. 44
10.7 White balance (Only available for color camera).............................................................. 45
White balance control methods.................................................................................................. 45
White balance control method selection.................................................................................... 45
White balance calculate region setting ...................................................................................... 46
10.8 Gamma correction............................................................................................................... 47
10.9 ROI (Region of Interest) ...................................................................................................... 47
10.10 Sensor Height Limitation ................................................................................................. 48
10.11 Pixel Format......................................................................................................................... 48
10.12 Precautions for STC-SBS1242POE................................................................................. 49
10.13 Trigger ............................................................................................................................... 50
Trigger signal processing procedure ......................................................................................... 50
10.14 Image Flip.......................................................................................................................... 51
10.15 LUT Control....................................................................................................................... 51
10.16 Defective pixel correction................................................................................................ 52
10.17 Counter And Timer Control ............................................................................................. 53
10.18 Event Control.................................................................................................................... 54
10.19 Chunk Control .................................................................................................................. 55
10.20 Action Control .................................................................................................................. 55
10.21 IEEE1588 ........................................................................................................................... 56
11 GenICam command............................................................................................ 58
11.1 DeviceControl ...................................................................................................................... 58
11.2 ImageFormatControl ........................................................................................................... 60
11.3 AcquisitionControl .............................................................................................................. 61
11.4 AnalogControl ..................................................................................................................... 62
11.5 LUTControl........................................................................................................................... 63

No.18S052-02
5/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
11.6 DigitalIOControl................................................................................................................... 64
11.7 LogicBlockControl .............................................................................................................. 64
11.8 SoftwareSignalControl........................................................................................................ 64
11.9 CounterAndTimerControl ................................................................................................... 65
11.10 EventControl........................................................................................................................ 66
11.11 UserSetControl .................................................................................................................... 66
11.12 ChunkDataControl............................................................................................................... 67
11.13 ActionControl ...................................................................................................................... 67
11.14 File AccessControl .............................................................................................................. 68
11.15 TestControl .......................................................................................................................... 68
11.16 TransportLayerControl ....................................................................................................... 69
12 Revision History................................................................................................. 71

No.18S052-02
6/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
Precautions for safe use
Please read carefully this “Precautions for safe use” before use the camera. Then the camera uses correctly with
agreeing with below notes.
In this “Precautions for safe use”, notes divides into “Warning” and “Caution” to use the camera safety and prevent to
harm and damage.
Warning
This shows, assumption for possibility of serious accident leading death or
serious injury if ignore this note and camera uses incorrectly.
Caution
This shows, assumption for possibility of bear the damage or physical
damage if ignore this note and camera uses incorrectly.
About Graphic
symbols
This symbol shows general prohibition.
This symbol shows completion or instruction.
[Environment / condition]
Warning
Do not use flammable or explosiveness
atmospheres.
This will cause of personal injury or fire.
Do not use for “safety for human body” related
usage.
This camera is designed for use “do not harm
human body immediately” if by any chance the
camera has malfunction.
Caution
Use and store under specified environmental
conditions (Vibration, shock, temperature,
humidity) in the specifications for this camera.
This will cause of fire or damage the camera.
[Installation and cable wiring]
Warning
Do not use with out of power voltage range
that is specified in the specifications for this
camera.
This will cause of fire, electrification or
malfunction.
Do not wrong wiring.
This will cause of fire or malfunction.

No.18S052-02
7/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
Caution
The camera housing and 0 V line of camera
inside circuit are isolated.
There is a risk of short circuit between camera
inside ciurcuit and frame ground through other
devices.
This will cause of malfunction.
It is necessary to wiring and mounting that is
specified in the specifications for this camera.
This will cause of fire or malfunction.
It is necessary to wiring with turn off the camera.
This will cause of electrification or malfunction.
It is necessary to mounting the camera without
stress for the cable.
This will case of electrification or fire.
[Usage instruction]
Warning
Do not touch the terminal and PCB board
While turn on the camera.
This will cause of electrification or accident
caused by malfunction.
Do not put combustibles near the camera.
This will cause of fire.
Do not use without usage that is specified in
the specifications for this camera.
This will cause of personal injury or malfunction.
Do not push metals including screw driver into
radiation holes.
This will cause of electrification or malfunction.
Do not touch the camera housing while or
afterusing the camera.
There is a risk of get burned.
Caution
Do not push contamination into opening of
the camera.
This will cause of electrification or malfunction.
Do not block the radiation holes.
This will cause of fire due to increase the
camera inside temperature.
[Maintenance]
Caution
Do not disassemble or repair the camera.
This will cause of fire, electrification or
malfunction.
It is turn off the camera when maintaining or
inspecting the camera.
This will cause of electrification.
[Disposal]
Caution
It is necessary to dispose as industrial waste.
]

No.18S052-02
8/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
1 Product Precautions
Do not give shock to the camera.
Do not haul or damage the camera cable.
Do not wrap the camera with any material while using the camera. This will cause the internal camera
temperature to increase.
When the camera moving or using the place that temperature difference is extreme, countermeasure for dew
condensation (heat removal / cold removal) is necessary.
While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting
in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.
・In wet, moist, high humidity or dusty place
・Under direct sunlight
・In extreme high or low temperature place
・Near an object that releases a strong magnetic or electric filed
・Place with strong vibrations
Apply the power that satisfies the specified in specifications for the camera.
The defective pixels may appear due to the sensor characteristics.
Use below recommend materials (or equivalent materials) to clean the surface of glass.
・Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)
・Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)
・Non-woven: nikowipe clean room (NKB)
Use a soft cloth to clean the camera.
2 Warranty
■Warranty period
One year after delivery (However, the camera had malfunction with camera uses correctly)
In below case for a fee even within warranty period.
・The malfunction caused by incorrect usage, incorrect modify or repair.
・The malfunction caused by external shock including the camera dropping after delivery the camera.
・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or
wrong voltage.
■Warranty coverage
Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.

No.18S052-02
9/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
3 Software Licensing
3.1 LWIP TCP/IP Licensing
The software in this camera includes LWIP TCP/IP implementation.
The copyright information is
Copyright (c) 2001-2004 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.

No.18S052-02
10/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
4 Introduction
This document describes the specification of the following cameras:
STC-MBS1242POE / STC-MCS1242POE
4.1 Features
GigE Interface
Support PoE (Power over Ethernet)
Small robust camera housing
Maximum frame rate (Full resolution): 9.2 fps @ 12M 8bits
CMOS (Global Reset Shutter / Rolling Shutter)
Up to 2,048 Defective Pixel Correction (Default: ON)
8bits, 10bits, 12bits output
4.2 Naming Method
STC-MxS1242POE
B: Monochrome
C: Color
1242: 1/1.7”, 12.4M Sensor
POE: PoE (Power over Ethernet (Gigabit Ethernet))
Sensor Manufacture
S: SONY

No.18S052-02
11/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
5 Specifications
5.1 Electronic Specifications
Product
STC-MBS1242POE
STC-MCS1242POE
Image Sensor
1/1.7” 12.4M Progressive Monochrome CMOS
(SONY: IMX226)
1/1.7” 12.4M Progressive Color CMOS
(SONY: IMX226)
Shutter Type
Global Rest / Rolling Shutter
Active Picture Elements
4,000 (H) x 3,000 (V)
Cell Size
1.85 (H) x 1.85 (V) µm
Sync System
External trigger (Hardware / Software) / Free run
Scanning Mode
Full scanning (Full resolution) / ROI
Frame
rate
(at full
scanning)
Rolling shutter, free run
8bits: 9.2 fps / 10bits: 4.7 fps / 10bits Packed: 6.3 fps /
12bits: 4.7 fps / 12bits Packed: 6.3 fps / RGB8: 3.0 fps
Maximum frame rate: 352.7 fps @ 2 lines (8bits) (*1)
Rolling shutter, free run /
Global reset
8bits / 10bits / 10bitsPacked / 12bits / 12bitsPacked: 4.6 fps
RGB8: 3.0 fps
ADC bit depth
12bits
Image Output Format
Mono8 / Mono10 / Mono10Packed /
Mono12 / Mono12Packed
Mono8 / Mono10 / Mono10Packed /
Mono12 / Mono12Packed /
BayerRG8 / BayerRG10 / BayerRG10Packed /
BayerRG12 / BayerRG12Packed / RGB8
Noise
Level
8bits output
Less than 2.8 digits (Gain 0 dB)
10bits / 10bits Packed output
Less than 11.2 digits (Gain 0 dB)
12bits / 12bits Packed output
Less than 44.8 digits (Gain 0 dB)
Sensitivity (*2)
2,240 Lux
4,440 Lux
Exposure Time (*3)
213 µseconds to 16.777 seconds (Default: 107,488 µseconds)
Gain
Analog Gain
0 to 15 dB (Default: 0 dB)
Digital Gain
x1 to x3 (Default: x1)
ROI
Horizontal: 40 to 4,000 pixels, Vertical: 2 to 3,000 lines (Default: 4,000 x 3,000)
Adjustable steps for size: 40 pixels in horizontal direction and 2 lines in vertical direction
Adjustable steps for offset: 40 pixels in horizontal direction and 2 lines in vertical direction
Gamma
Gamma 0.1 to 4.0 (Default: 1.0)
Binning
N/A
Decimation Function
N/A
Image Flip
Vertical / Off (Un-support: Horizontal)
Defective Pixel Correction
Up to 2,048 points (Default: On)
Auto
Image
Control
Auto Exposure
Support (Default: OFF)
Auto Gain
Support (Default: OFF)
Auto White Balance
N/A
Auto / Manual / Push to Set
Operational Mode
Edge preset trigger / Pulse width trigger / Free run
Interface
PoE: IEEE802.3af CLASS2 (1000BASE-T)
Protocol
GigE Vision 2.1 and GenICam SFNC 2.4, IEEE1588 (PTP)
I/O
One opto-isolated input, one opto-isolated output and one open collector GPIO (Input or output)
Power
Input Voltage (*4)
+10.8 to +26.4 Vdc External power (via 6 pin connector) /
Power Over Ethernet (IEEE802.3af)
Consumption
+12 V / +24 V: 3.3 W, PoE: 4.0 W
Default: Bold

No.18S052-02
12/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
Precautions
(*1) Sensor Height minimum limitation setting
(*2) The sensitivity is measuring the luminance when white level achieved 100 % in below conditions.
(*3) The exposure time range for RGB8 pixel format is 423 μseconds to 16.777 seconds.
(*4) The camera operates with external power when power suppling by external power supply and PoE to camera
at same time.
Camera Setting
Environment
Parameter
Setting
Parameter
Setting
Gain Up
0 dB
Light Source
Light Box (White)
AGC
Off
Color temperature
5,100K
White Balance
Optimum
Lens
Electrical Shutter
1/30 seconds
F on Lens
F5.6
Black Level
Optimum
Target Luminance
IM-600 (Topcon)
Gamma
Factory Setting

No.18S052-02
13/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
5.2 Spectral Sensitivity Characteristics
STC-MBS1242POE
STC-MCS1242POE (without IR Cut Filter)

No.18S052-02
14/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
IR Cut Filter (STC-MCS1242POE)
5.3 Mechanical Specifications
Model Number
STC-MBS1242POE
STC-MCS1242POE
Dimensions
29 (W) x 29 (H) x 53 (D) mm (*1)
Optical Filter
No Optical Filter
IR Cut Filter
Optical Center Accuracy
Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 1.5 deg.
Material
Aluminum Alloy (AC)
Lens Mount
C mount
Interface Connectors
Ethernet connector: RJ45 connector
Power- I/O connector: HR10A-7R-6PB (Hirose) or equivalent
Camera Mounting
Six M3 screw holes (Two on top, four on bottom plate)
Weight
Approximately 65 g
(*1) Excluding the connectors

No.18S052-02
15/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
5.4 Environmental Specifications
Model Number
STC-MBS1242POE
STC-MCS1242POE
Operational
Temperature /
Humidity
Minimum
Environmental Temperature: 0 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Maximum
Environmental Temperature: +40 deg. C or
Camera housing temperature (top plate) shall not exceed +61 deg. C (*1)
Environmental Humidity: 0 to 85 %RH (No condensation)
Storage Temperature / Humidity
Environmental Temperature: -20 to +70 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Vibration
20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G, XYZ 3 directions, 30 min. each
Shock
Acceleration 38 G, half amplitude 6 ms, XYZ 3 directions, 3 times each
Standard Compliancy
EMS: EN61000-6-2, EMI: EN55011
RoHS
RoHS Compliance
(*1) Please insure the camera is installed with the appropriate heat dissipation. If camera has a mounted lens and a tripod
with an aluminum plate, this could decrease the camera housing temperature for heat dissipation. When the internal
temperature sensor on the camera shows less than 72 deg. C, the camera housing temperature (top plate) will be less than
61 deg. C.
Taking these steps will maintain the heat rating of the electronic components of the camera.
Upper side of camera
Measuring point

No.18S052-02
16/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
6 Connector Specifications
6.1 RJ45 Connector
This product is PoE compliant.
Please supply power (+10.8 to +26.4 Vdc) through the power-I/O connector when using non-PoE-compliant
NIC.
Pin Assignment LED
Pin No.
Signal Name
1
TA+
2
TA-
3
TB+
4
TC+
5
TC-
6
TB-
7
TD+
8
TD-
Please use a 1GB supported NIC, Network Switcher and Ethernet cable.
Check the setting of NIC and Network Switcher being used is “1GB transferring”.
Green LED
Yellow LED
Status
Green Light ON
Yellow Light OFF
Power ON (1GB NIC)
Green Light OFF
Yellow Light OFF
Power ON (100MB NIC)
Green Light ON
Yellow Light Blinking
1 GB Transferring
Green Light OFF
Yellow Light Blinking
100 MB Transferring
Camera is powered-on
Green light: ON
Yellow light: Blinking
1 GB Transferring
Green light: OFF
Yellow light: Blinking
100 MB Transferring
Power-I/O Connector
RJ45 Connector
Yellow LED
Green LED

No.18S052-02
17/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
6.2 Power and Control Signal Connector
HR10A-7R-6PB (Hirose) or equivalent
This connector is for the power supply and input / output signals.
The power from this connector is priority power for camera when power supplies through this connector and
PoE at same time.
Please use HR10A-7P-6S (Hirose) or equivalent for cable.
Pin assignment
Configuration of Line2 (Pin No.3) and Line1 (Pin No.4)
Output signal can be assign by GenICam command.
.
Pin No.
Signal Name
IN / OUT
Voltage
1
POWER IN
IN
+10.8 to +26.4 Vdc
2
Opto-isolated in
(Line0)
IN
Low: Smaller than +1.0 V
High: +3.0 to +26.4 V
* Potential difference between
TRG_in and Opt. Isolated Common
3
Open Collector
GPIO
(Line2)
IN / OUT
+3.0 to +26.4 V / Open Collector
4
Opto-isolated out
(Line1)
OUT
Open Collector
5
Opto-isolated
Common
IN
6
GND
IN
0 V
GenICam
1) Frame Trigger Wait (Default for all output)
2) Frame Trigger Internal
3) Exposure Active
4) Acquisition Trigger Wait
5) Acquisition Trigger Internal
6) Sensor Read Out
7) Debounced Line 0
8) Debounced Line 2
9) User Output 1
10) User Output 2
11) Timer 0 Active
12) Software Signal 0
13) Software Signal 1
14) Logic Block 0
15) Pulse Per Second
16) Flash Window

No.18S052-02
18/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
1) Frame Trigger Wait
The condition of camera operation with trigger signal can be check.
“LOW” state of signal is out between “start exposing” to “image out”.
2) Frame Trigger Internal
The input trigger signal with the trigger delay (camera internal process delay).
3) Exposure Active
While camera exposing, “HIGH” state of signal is out. The signal state will be “LOW” after finish
exposing.
4) Acquisition Trigger Wait
While image transferring from camera to PC, “Low” state of signal is out. The signal state will be
“High” after finish image transferring.
5) Acquisition Trigger Internal
The image transferring starts signal is out.
6) Sensor Read Out
FVAL (Frame valid, HIGH state) signal is out.
7) Debounced Line0
Debounced Line0 signal is out.
8) Debounced Line2
Debounced Line2 signal is out.
9) User Output 1 (User Output signal through Line 1)
Selected “HIGH” or “LOW” state of signal is out.
10) User Output 2 (User Output signal through Line 2)
Selected “HIGH” or “LOW” state of signal is out.
11) Timer 0 Active
Selected signal at “Timer Counter” is out.
When signal synchronizing with “Exposure Active” signal, signal can use for strobe control.
12) Software Signal 0
Selected signal for “Software Signal 0” at “Software Signal Control” is out.
13) Software Signal 1
Selected signal for “Software Signal 1” at “Software Signal Control” is out.
14) Logic Block 0
“Logic Block 0” signal is out.
15) Pulse Per Second
“Pulse / second” signal (50% Duty, 1 Hz interval) is out.

No.18S052-02
19/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
16) Flash Window
The external light source control signal is out.
This signal can be used to set active time of light source for rolling shutter to acquire acceptable
image.
Line0
Line1
Line2
LineN-1
LineN
Rolling shutter
Line0
Line1
Line2
LineN-1
LineN
Global Reset shutter

No.18S052-02
20/72
STC-MBS1242POE / STC-MCS1242POE
Product Specifications and User’s Guide
Opto-isolated input
The camera has current limiting circuit on camera. The current limiting resistor does not necessary.
Opto-isolated output
It is necessary to have current limiting resistor at outside of camera, to keep less than 50 mA.