Omron STC-SBS312POE Installation instructions

No.16S019-05
1/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
GigE Vision Camera
CMOS Color / Monochrome
STC-SBS312POE (3.2M / Monochrome)
STC-SCS312POE (3.2M / Color)
STC-SBS500POE (5.0M / Monochrome)
STC-SCS500POE (5.0M / Color)
Product Specifications and User’s Guide
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
2/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
Table of Contents
1 Product Precautions ............................................................................................ 7
2 Warranty ................................................................................................................ 7
3 Introduction .......................................................................................................... 8
3.1 Features .................................................................................................................................... 8
3.2 Product Number Naming Method ........................................................................................... 8
4 Specifications ....................................................................................................... 9
4.1 Electronic Specifications ......................................................................................................... 9
STC-SBS312POE / STC-SCS312POE ............................................................................................... 9
STC-SBS500POE / STC-SCS500POE .............................................................................................. 11
4.2 Spectral Sensitivity Characteristics ..................................................................................... 13
STC-SBS312POE ............................................................................................................................. 13
STC-SCS312POE (without IR cut filter) ......................................................................................... 13
STC-SBS500POE ............................................................................................................................. 14
STC-SCS500POE (without IR cut filter) ......................................................................................... 14
IR Cut Filter (STC-SCS312POE / STC-SCS500POE) ...................................................................... 15
4.3 Mechanical Specifications ..................................................................................................... 16
STC-SBS312POE / STC-SCS312POE ............................................................................................. 16
STC-SBS500POE / STC-SCS500POE ............................................................................................. 16
4.4 Environmental Specifications ............................................................................................... 17
STC-SBS312POE / STC-SCS312POE ............................................................................................. 17
STC-SBS500POE / STC-SCS500POE ............................................................................................. 17
5 Connector Specifications .................................................................................. 19
5.1 RJ45 Connector ...................................................................................................................... 19
5.2 Power and Control Signal Connector ................................................................................... 20
Equivalent Circuit for the Input Pin of the I/O Connector ............................................................. 22
Typical Input Circuit ........................................................................................................................ 23
Typical Output Circuit ..................................................................................................................... 24
Input and Output Signal Timing (Hardware Trigger) ..................................................................... 25
Input and Output Signal Timing (Software Trigger) ...................................................................... 26
6 Dimensions ......................................................................................................... 27
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
3/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
6.1 STC-SBS312POE / STC-SBS500POE .................................................................................... 27
6.2 STC-SCS312POE / STC-SCS500POE .................................................................................... 28
7 Sensor information ............................................................................................ 29
7.1 Pixel Transferring Image ........................................................................................................ 29
8 Camera Operational Modes ............................................................................... 30
8.1 Normal Mode ........................................................................................................................... 30
8.2 Pulse width trigger mode....................................................................................................... 30
Timing .............................................................................................................................................. 30
Exposure Timing with the Positive Polarity Trigger Signal .......................................................... 31
Exposure Timing with the Negative Polarity Trigger Signal ........................................................ 31
8.3 Edge Preset Trigger Mode ..................................................................................................... 32
Timing .............................................................................................................................................. 32
Exposure Timing with the Positive Polarity Trigger Signal .......................................................... 33
Exposure Timing with the Negative Polarity Trigger signal ......................................................... 33
8.4 Edge Preset Trigger Mode (Trigger Input While the Image Is Out) ..................................... 34
Timing .............................................................................................................................................. 34
9 Camera Functions .............................................................................................. 35
9.1 ROI (Region of Interest) ......................................................................................................... 35
ROI (1 region) .................................................................................................................................. 35
9.2 Pixel Format ............................................................................................................................ 37
9.3 Decimation .............................................................................................................................. 37
9.4 Image Flip................................................................................................................................ 38
9.5 Gain ......................................................................................................................................... 40
Analog gain ..................................................................................................................................... 40
Digital gain ...................................................................................................................................... 40
9.6 Black level ............................................................................................................................... 40
9.7 ALC (Auto Light Control) ....................................................................................................... 41
ALC control method........................................................................................................................ 42
AGC (Auto Gain Contorl) ................................................................................................................ 42
Auto shutter .................................................................................................................................... 43
ALC settings procedure ................................................................................................................. 43
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
4/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
9.8 White balance (Only available for the color cameras) ........................................................ 44
White balance control methods ..................................................................................................... 44
OFF .................................................................................................................................................. 45
Auto white balance ......................................................................................................................... 45
Push to set white balance .............................................................................................................. 45
Preset white balance1 to 3 ............................................................................................................. 46
White balance calculate area setting ............................................................................................. 47
9.9 Gamma correction .................................................................................................................. 48
Gamma table writing ....................................................................................................................... 48
9.10 Save and load the camera setting data ............................................................................. 49
The camera settings saving ........................................................................................................ 49
The camera settings loading ....................................................................................................... 50
The camera settings loading when the camere power is on. ................................................... 50
The camera settings initialization ............................................................................................... 50
9.11 Trigger .................................................................................................................................. 51
Trigger signal processing procedure ......................................................................................... 51
9.12 The camera settings (GenICam parameters) control with SDK ....................................... 52
Integer type parameter control ................................................................................................... 52
Float type parameter control ....................................................................................................... 52
Enumeration type parameter control ......................................................................................... 52
String type paramter control ....................................................................................................... 53
Boolean type parameter control ................................................................................................. 53
Command type paramter control ................................................................................................ 53
9.13 GenICam Command List ..................................................................................................... 54
DeviceControl .............................................................................................................................. 54
ImageFormatControl.................................................................................................................... 54
AcquisitionControl ...................................................................................................................... 55
DigitalIOControl ........................................................................................................................... 55
CounterAndTimerControl ............................................................................................................ 56
EventControl ................................................................................................................................ 56
AnalogControl .............................................................................................................................. 56
TransportLayerControl ................................................................................................................ 57
UserSetControl ............................................................................................................................ 58
IPEngine ....................................................................................................................................... 58
SpecialFeatures ........................................................................................................................... 59
10 Revision History ................................................................................................. 61
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
5/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
Precautions for safe use
Please read carefully this “Precautions for safe use” before use the camera. Then the camera uses correctly with
agreeing with below notes.
In this “Precautions for safe use”, notes divides into “Warning” and “Caution” to use the camera safety and prevent to
harm and damage.
Warning This shows, assumption for possibility of serious accident leading death or
serious injury if ignore this note and camera uses incorrectly.
Caution This shows, assumption for possibility of bear the damage or physical
damage if ignore this note and camera uses incorrectly.
About Graphic
symbols This symbol shows general prohibition.
This symbol shows completion or instruction.
[Environment / condition]
Warning
Do not use flammable or explosiveness
atmospheres.
This will cause of personal injury or fire.
Do not use for “safety for human body” related
usage.
This camera is designed for use “do not harm
human body immediately” if by any chance the
camera has malfunction.
Caution
Use and store under specified environmental
conditions (Vibration, shock, temperature,
humidity) in the specifications for this camera.
This will cause of fire or damage the camera.
[Installation and cable wiring]
Warning
Do not use with out of power voltage range
that is specified in the specifications for this
camera.
This will cause of fire, electrification or
malfunction.
Do not wrong wiring.
This will cause of fire or malfunction.
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
6/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
Caution
The camera housing is not connecting to 0 V
line of camera inside circuit.
There is a risk of short circuit between camera
inside ciurcuit and frame ground through other
devices.
This will cause of malfunction.
It is necessary to wiring and mounting that is
specified in the specifications for this camera.
This will cause of fire or malfunction.
It is necessary to wiring with turn off the camera.
This will cause of electrification or malfunction.
It is necessary to mounting the camera without
stress for the cable.
This will case of electrification or fire.
[Usage instruction]
Warning
Do not touch the terminal and PCB board
While turn on the camera.
This will cause of electrification or accident
caused by malfunction.
Do not put combustibles near the camera.
This will cause of fire.
Do not use without usage that is specified in
the specifications for this camera.
This will cause of personal injury or malfunction.
Do not push metals including screw driver into
radiation holes.
This will cause of electrification or malfunction.
Caution
Do not push contamination into opening of
the camera.
This will cause of electrification or malfunction.
Do not block the radiation holes.
This will cause of fire due to increase the
camera inside temperature.
[Maintenance]
Caution
Do not disassemble or repair the camera.
This will cause of fire, electrification or
malfunction.
It is turn off the camera when maintaining or
inspecting the camera.
This will cause of electrification.
[Disposal]
Caution
It is necessary to dispose as industrial waste.
]
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
7/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
1 Product Precautions
 Do not give shock to the camera.
 Do not haul or damage the camera cable.
 Do not wrap the camera with any material while using the camera. This will cause the internal camera
temperature to increase.
 When the camera moving or using the place that temperature difference is extreme, countermeasure for
dew condensation (heat removal / cold removal) is necessary.
 While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting
in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.
・ In wet, moist, high humidity or dusty place
・ Under direct sunlight
・ In extreme high or low temperature place
・ Near an object that releases a strong magnetic or electric filed
・ Place with strong vibrations
 Apply the power that satisfies the specified in specifications for the camera.
 The defective pixels may appear due to the sensor characteristics.
 Use below recommend materials (or equivalent materials) to clean the surface of glass.
・ Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)
・ Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)
・ Non-woven: nikowipe clean room (NKB)
 Use a soft cloth to clean the camera.
2 Warranty
■Warranty period
One year after delivery (However, the camera had malfunction with camera uses correctly)
In below case for a fee even within warranty period.
・The malfunction caused by incorrect usage, incorrect modify or repair.
・The malfunction caused by external shock including the camera dropping after delivery the camera.
・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or
wrong voltage.
■Warranty coverage
Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
8/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
3 Introduction
This document describes the specification of the following cameras:
STC-SBS312POE / STC-SCS312POE
STC-SBS500POE / STC-SCS500POE
3.1 Features
 Support PoE (Power Over Ethernet)
 Maximum Frame Rate (Full Scanning): 33.3 fps @ 3.2M 8bits, 21 fps @ 5.0M 8bits
 CMOS (Global Shutter)
 Defective Pixel Correction up to 64 points
 8bits, 10bits or 12bits output
3.2 Product Number Naming Method
STC-SxS312POE
Sensor Manufacture
S: SONY
312: 3.2M, 1/1.8” sensor
500: 5.0M, 2/3” sensor
POE: PoE (Power over Ethernet GigE)
B: Monochrome
C: Color
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
9/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
4 Specifications
4.1 Electronic Specifications
STC-SBS312POE / STC-SCS312POE
Model Number STC-SBS312POE STC-SCS312POE
Image sensor 1/1.8” 3.2M Monochrome Progressive CMOS
(Sony: IMX265)
1/1.8” 3.2M Color Progressive CMOS
(Sony: IMX265)
Shutter Type Global Shutter
Active Picture Elements 2,048 (H) x 1,536 (V)
Cell Size 3.45 (H) x 3.45 (V) µm
Scanning System Progressive
Sync Method External trigger (Hardware / Software) / Free run
Maximum 8bits output 33.3 fps
Frame Rate 10bits output 16.6 fps
(at Full 10bits Packed output 22.2 fps
scanning) 12bits output 16.6 fps
12bits Packed output 22.2 fps
ADC bit depth 12bits
Image Output Format Mono8 / Mono10 / Mono10Packed /
Mono12 / Mono12Packed
BayerBG8 / BayerBG10 /
BayerBG10Packed /
BayerBG12 / BayerBG12Packed
Noise Level 8bits output Less than 3 digits (Gain 0 dB)
10bits / 10bits Packed output Less than 12 digits (Gain 0 dB)
12bits / 12bits Packed output Less than 48 digits (Gain 0 dB)
Sensitivity 300 Lux 780 Lux
Electronic 8bits output 1 µsecond to 16.777 seconds (Default: 29,613 µseconds)
Shutter 10bits / 10bits Packed output
12bits / 12bits Packed output
Gain Analog 0 to 20.8 dB (Default: 0 dB)
Digital x1 to x2 (Default: x1)
ROI Horizontal: 264 to 2,048 pixels / Vertical: 4 to 1,536 pixels (Default: 2,048 x 1,536)
Adjustable steps for the image size: 8 pixels in horizontal direction and 2 lines in vertical direction
Adjustable steps for the offset: 8 pixels in horizontal direction and 2 lines in vertical direction
Multi ROI N/A
Gamma Gamma 1.0 or uploadable gamma table (Default:1.0)
Binning Function N/A
Decimation Function Horizontal and Vertical decimation (2x2) / Off
Mirror image Horizontal / Vertical / Horizontal and vertical / Off
Pixel Blemish Correction Up to 64 points
Auto Image Auto Exposure Support Support
Control Auto Gain (AGC) Support Support
Auto White Balance N/A Support
Default: Bold
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
10/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
Model Number STC-SBS312POE STC-SCS312POE
Operational Mode Edge preset trigger /
Pulse width trigger (more than 13.3333 µseconds (8bits), 17.77778 µseconds (10bits,12bits)
active pulse) / Free run
Communication UART communication through Ethernet port
Interface IEEE802.3af CLASS2 (1000BASE-T)
Protocol GigE Vision 1.2 and GenICam Standard Version 2.1 (SFNC 1.4)
I/O One opt-isolated input and two open collector outputs (+3.3 V)
Power Input Voltage +10.8 to +26.4 Vdc (Power/IO connector) / Power Over Ethernet (IEEE802.3af)
Consumption +12 V: 2.9 W, +24 V:3.3 W, PoE: 3.5 W
Default: Bold
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
11/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
STC-SBS500POE / STC-SCS500POE
Model Number STC-SBS500POE STC-SCS500POE
Image Sensor 2/3” 5.0M Monochrome progressive CMOS
(Sony: IMX264)
2/3” 5.0M Color Progressive CMOS
(Sony: IMX264)
Shutter Type Global Shutter
Active Picture Elements 2,448 (H) x 2,048 (V)
Cell Size 3.45 (H) x 3.45 (V) µm
Scanning System Progressive
Sync Method External trigger (Hardware / Software) / Free run
Maximum 8bits output 21 fps
Frame Rate 10bits output 10.5 fps
(at Full 10bits Packed output 14 fps
scanning) 12bits output 10.5 fps
12bits Packed output 14 fps
ADC bit depth 12bit
Image Output Format Mono8 / Mono10 / Mono10Packed /
Mono12 / Mono12Packed
BayerBG8 / BayerBG10 /
BayerBG10Packed /
BayerBG12 / BayerBG12Packed
Noise Level 8bits output Less than 3 digits (Gain 0 dB)
10bits / 10bits Packed output Less than 12 digits (Gain 0 dB)
12bits / 12bits Packed output Less than 48 digits (Gain 0 dB)
Sensitivity 300 Lux 780 Lux
Electronic 8bits output 1 µsecond to 16.777 seconds (Default: 47,458 µseconds)
Shutter 10bits / 10bits Packed output
12bits / 12bits Packed output
Gain Analog 0 to 20.8 dB (Default: 0dB)
Digital 0 to 6 dB (Default: 0dB)
ROI Horizontal: 264 to 2,448 pixels / Vertical: 4 to 2,048 pixels (Default: 2,448 x 2,048)
Adjustable steps for the image size: 8 pixels in horizontal direction and 2 lines in vertical direction
Adjustable steps for the offset: 8 pixels in horizontal direction and 2 lines in vertical direction
Multi ROI N/A
Gamma Gamma 1.0 or uploadable gamma table (Default:1.0)
Binning Function N/A
Decimation Function Horizontal and Vertical decimation (2x2) / Off
Mirror image Horizontal / Vertical / Horizontal and vertical / Off
Pixel Blemish Correction Up to 64 points
Auto Image Auto Exposure Support Support
Control Auto Gain (AGC) Support Support
Auto White Balance N/A Support
Default: Bold
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
12/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
Model Number STC-SBS500POE STC-SCS500POE
Operational Mode Edge preset trigger /
Pulse width trigger (more than 15.75758 µseconds (8bits), 21.0101 µseconds (10bits,12bits)
active pulse) / Free run
Communication UART communication through Ethernet port
Interface IEEE802.3af CLASS2 (1000BASE-T)
Protocol GigE Vision 1.2 and GenICam Standard Version 2.1 (SFNC 1.4)
I/O One opt-isolated input and two open collector outputs
Power Input Voltage +10.8 to +26.4 Vdc (Power/IO connector) / Power Over Ethernet (IEEE802.3af)
Consumption +12V: 2.9 W, +24V:3.3 W, PoE: 3.5 W
Default: Bold
Precautions
(*1) The sensitivity is measuring the luminance when white level achieved 100 % in below conditions.
Camera Setting Environment
Parameter Setting Parameter Setting
Gain Up 0 dB Light Source Light Box (White)
AGC OFF Color temperature 5,100 K
White Balance Optimum
Electrical Shutter 1/30 seconds F on Lens F5.6
Black Level Optimum Target Luminance IM-600 (Topcon)
Gamma Factory Setting
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
13/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
4.2 Spectral Sensitivity Characteristics
STC-SBS312POE
STC-SCS312POE (without IR cut filter)
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
14/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
STC-SBS500POE
STC-SCS500POE (without IR cut filter)
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
15/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
IR Cut Filter (STC-SCS312POE / STC-SCS500POE)
Wave Length (nm)
Transmittance
(%)
Spectrum Transmittance (Reference)
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
16/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
4.3 Mechanical Specifications
STC-SBS312POE / STC-SCS312POE
Model Number STC-SBS312POE STC-SCS312POE
Dimensions 35 (W) x 35 (H) x 53.4 (D) mm (*1) 35 (W) x 35 (H) x 53.7 (D) mm (*1)
Optical Filter No Optical Filter IR cut filter
Optical Center Accuracy Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 2.0 deg.
Material Aluminum Alloy (AC)
Lens Mount C mount
Connectors Ethernet connector: RJ45 connector
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent
Camera Mount Screws Two 1/4” Tripod screw holes: (One on top and bottom plate)
Eight M4 screws holes: (Four on top and bottom plate)
Weight Approximately 120 g
(*1) Excluding connectors
(*2) Recommend lens: More than F2.8 (Close side)
STC-SBS500POE / STC-SCS500POE
Model Number STC-SBS500POE STC-SCS500POE
Dimensions 35 (W) x 35 (H) x 53.4 (D) mm (*1) 35 (W) x 35 (H) x 53.7 (D) mm (*1)
Optical Filter No Optical Filter IR cut filter
Optical Center Accuracy Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 2.0 deg.
Material Aluminum Alloy (AC)
Lens Mount (*2) C mount
Connectors Ethernet connector: RJ45 connector
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent
Camera Mount Screws Two 1/4” Tripod screw holes: (One on top and bottom plate)
Eight M4 screws holes: (Four on top and bottom plate)
Weight Approximately 120 g
(*1) Excluding connectors
(*2) Recommend lens: More than F2.8 (Close side)
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
17/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
4.4 Environmental Specifications
STC-SBS312POE / STC-SCS312POE
Model Number STC-SBS312POE STC-SCS312POE
Operational
Temperature / Humidity
Minimum Environmental Temperature: 0 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Maximum (*1) Camera housing temperature (top plate) shall not exceed 60 deg. C
(This corresponds to an environmental temperature of approximately 40 deg. C),
Environmental Humidity: 0 to 85 %RH (No condensation)
Storage Temperature / Humidity Environmental Temperature: -20 to +80 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Vibration 20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G,
XYZ 3 directions 30 min. each
Shock Acceleration 38 G, half amplitude 6 mseconds, XYZ 3 directions, 3 times each
Standard Compliancy EMS: EN61000-6-2, EMI: EN55011
RoHS RoHS Compliance
STC-SBS500POE / STC-SCS500POE
Model Number STC-SBS500POE STC-SCS500POE
Operational
Temperature / Humidity
Minimum Environmental Temperature: 0 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Maximum (*1) Camera housing temperature (top plate) shall not exceed +60 deg. C
(This corresponds to an environmental temperature of approximately +40 deg. C),
Environmental Humidity: 0 to 85 %RH (No condensation)
Storage Temperature / Humidity Environmental Temperature: -20 to +80 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Vibration 20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G,
XYZ 3 directions 30 min. each
Shock Acceleration 38 G, half amplitude 6 mseconds, XYZ 3 directions, 3 times each
Standard Compliancy EMS: EN61000-6-2, EMI: EN55011
RoHS RoHS Compliance
(*1) When the camera using under the condition that exceeds +40 deg. C environmental temperature, please insure the
camera installs with the appropriate heat dissipation to keep the housing temperature less than +60 deg. C.
If camera has a mounted lens and a tripod with an aluminum plate, this could decrease the camera housing
temperature for heat dissipation.
When the internal temperature sensor on the camera shows less than +65 deg. C, the camera housing temperature
(top plate) will be less than +60 deg. C.
Taking these steps will maintain the heat rating of the electronic components of the camera.
]
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
18/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
Upper side of camera
Measuring point
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
19/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
5 Connector Specifications
5.1 RJ45 Connector
This product is PoE compliant.
Please supply power (+10.8 to +26.4 Vdc) through the power-I/O connector when using non-PoE-compliant
NIC.
Pin Assignment LED
Pin No. Signal Name
1 TA+
2 TA-
3 TB+
4 TC+
5 TC-
6 TB-
7 TD+
8 TD-
Please use a 1GB supported NIC, Network Switcher and LAN cable. Check that the NIC and Network
Switcher being used is “1GB transferring”.
Green LED Yellow LED Status
Green Light ON Yellow Light ON Power ON (1GB NIC)
Green Light OFF Yellow Light OFF Power ON (100MB NIC)
Green Light ON Yellow Light Blinking 1Gb Transferring
Green Light OFF Yellow Light Blinking 100 Mb Transferring
Power-I/O Connector
RJ45 Connector
Camera is powered-on Green LED: ON
Yellow LED: Blinking
1 GB Transferring
Green LED: OFF
Yellow LED: Blinking
100 MB Transferring
Yellow LED
Green LED
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.

No.16S019-05
20/62
STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE
Product Specifications and User’s Guide
5.2 Power and Control Signal Connector
 HR10A-7R-6PB（Hirose）or equivalent
 This connector is for the power supply and input /output signals.
The power from this connector is priority power for the camera when the power supplies through this connector
and PoE at same time.
 Use HR10A-7P-6S (Hirose) or equivalent for the cable side.
Pin assignment
Pin No. Signal Name
IN /
OUT
Voltage
1 GND IN 0 V
2 I/O-1 OUT +3.3 V Open Collector
3 I/O-2 OUT +3.3 V Open Collector
4 TRG_In-
(Opt. Isolated -) IN Low: Smaller than +1.0 V
High: +3.0 to +26.4V
* potential difference between TRG_In-
and TRG_In+
5 TRG_In+
(Opt. Isolated +)
IN
6 POWER IN IN +10.8 to +26.4 Vdc
Configuration of I/O-1 (Pin No.2) and I/O-2 (Pin No.3)
Output pin can be assigned through register setting or GenICam Command.
GenICam command
I/O-1 (Pin No.2) / I/O-2 (Pin No.3)
1) FrameTriggerWait (initial setting for I/O-1)
2) UserOutput
3) ExposureActive (initial setting for I/O-2)
4) TriggerAuxiliary
5) TriggerInternal
6) SensorReadOut
7) StrobeSignal
For more information please contact Aegis Electronic Group, Inc. *[phone] *[email protected] *http://www.aegiselect.com
Aegis Electronic Group, Inc.