Omron CoaXPress STC-LBGP251BCXP124 Installation instructions

No.20S062-00
1/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
CoaXPress
Monochrome / Color CMOS Camera
STC-LBGP251BCXP124
(25M / Monochrome / High speed / CXP-12x4 / Connector on rear)
STC-LCGP251BCXP124
(25M / Color / High speed / CXP-12x4 / Connector on rear)
STC-LBGP251BCXP124-T
(25M / Monochrome / High speed / CXP-12x4 / Connector on top)
STC-LCGP251BCXP124-T
(25M / Color / High speed / CXP-12x4 / Connector on top)
Product Specifications and User’s Guide

No.20S062-00
2/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
Table of Contents
1 Product Precautions ........................................................................................................................................................ 7
2 Product conformity / compliance ................................................................................................................................... 7
3 Warranty ........................................................................................................................................................................... 7
4 Overview ........................................................................................................................................................................... 8
4.1 Features ..................................................................................................................................................................... 8
4.2 Product Number Naming Method ............................................................................................................................... 8
5 Specifications .................................................................................................................................................................. 9
5.1 Electronic Specifications............................................................................................................................................. 9
5.2 Spectral Sensitivity Characteristics ...........................................................................................................................11
5.3 Mechanical Specifications ........................................................................................................................................ 12
5.4 Environmental Specifications ................................................................................................................................... 13
5.5 External Connector Specifications ........................................................................................................................... 14
5.5.1 Micro BNC connector ........................................................................................................................................ 14
5.5.2 Power/IO Connector .......................................................................................................................................... 15
5.5.3 Connector indicator lamp .................................................................................................................................. 17
6 Dimensions .................................................................................................................................................................... 18
6.1 STC-LBGP251BCXP124 / STC-LCGP251BCXP124 .............................................................................................. 18
6.2 STC-LBGP251BCXP124-T / STC-LCGP251BCXP124-T ........................................................................................ 19
7 Sensor Information ........................................................................................................................................................ 20
7.1 Pixel Transferring Image........................................................................................................................................... 20
8 Camera Operational Modes .......................................................................................................................................... 21
8.1 Normal Mode ............................................................................................................................................................ 21
8.2 Edge Preset Trigger Mode ....................................................................................................................................... 22
8.3 Pulse width trigger mode .......................................................................................................................................... 22
8.4 Frame rate ................................................................................................................................................................ 23
8.5 The interval of trigger input ....................................................................................................................................... 24
8.5.1 The interval of trigger input when trigger overlap is disabling ........................................................................... 24
8.6 Burst trigger .............................................................................................................................................................. 25
9 Camera Functions ......................................................................................................................................................... 26
9.1 CXP Configuration .................................................................................................................................................... 26
9.2 Device Indicator Mode .............................................................................................................................................. 26
9.3 Pixel Format ............................................................................................................................................................. 27
9.4 Frame rate ................................................................................................................................................................ 27
9.5 Exposure Time .......................................................................................................................................................... 27
9.6 Trigger ...................................................................................................................................................................... 28
9.7 Image Flip ................................................................................................................................................................. 28
9.8 Black Level ............................................................................................................................................................... 29
9.9 Gain .......................................................................................................................................................................... 29
9.9.1 Analog Gain ....................................................................................................................................................... 29
9.9.2 Digital Gain ........................................................................................................................................................ 29
9.10 White Balance (Only available for color model) ....................................................................................................... 30
9.10.1 Disable .............................................................................................................................................................. 30
9.10.2 Manual (Off) ...................................................................................................................................................... 30
9.10.3 Auto White Balance (Continuous) ..................................................................................................................... 30
9.10.4 Push to Set White Balance (Once) ................................................................................................................... 30
9.11 Binning (Only available for monochrome model) ..................................................................................................... 31
9.12 Decimation ................................................................................................................................................................ 32
9.13 ROI (Region of Interest) ........................................................................................................................................... 33
9.13.1 ROI (One Region) ............................................................................................................................................. 33

No.20S062-00
3/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
9.14 Multi ROI ................................................................................................................................................................... 34
9.15 Flat Field Correction Control .................................................................................................................................... 35
9.15.1 FFC function procedure .................................................................................................................................... 36
9.16 Gamma Table ........................................................................................................................................................... 37
9.17 Pixel Defect Correction ............................................................................................................................................. 38
9.18 Event Control ............................................................................................................................................................ 39
9.19 Save and load camera settings ................................................................................................................................ 40
9.19.1 Saving the Camera Settings ............................................................................................................................. 40
9.19.2 Loading Camera Settings .................................................................................................................................. 41
9.19.3 Loading Camera Settings when the Camera Power is on ................................................................................ 41
9.19.4 Camera Settings Initialization ............................................................................................................................ 41
10 IO Function ................................................................................................................................................................. 42
10.1 Input Port Function ................................................................................................................................................... 42
10.1.1 Trigger Input ...................................................................................................................................................... 42
10.1.2 Line Status ........................................................................................................................................................ 42
10.1.3 Line Debouncer ................................................................................................................................................. 43
10.1.4 Trigger Delay ..................................................................................................................................................... 43
10.2 Output Port Function ................................................................................................................................................ 44
10.2.1 Line Source ....................................................................................................................................................... 44
10.2.2 User Output ....................................................................................................................................................... 46
10.2.3 Line Status ........................................................................................................................................................ 46
10.2.4 Output signal duration setting and Pulse width setting ..................................................................................... 46
11 GenICam command list ............................................................................................................................................. 47
11.1 DeviceControl ........................................................................................................................................................... 47
11.2 ImageFormatControl ................................................................................................................................................. 48
11.3 AcquisitionControl ..................................................................................................................................................... 49
11.4 TransportLayerControl .............................................................................................................................................. 50
11.5 DigitalIOControl ........................................................................................................................................................ 50
11.6 AnalogControl ........................................................................................................................................................... 51
11.7 LUTControl ............................................................................................................................................................... 51
11.8 Event Control ............................................................................................................................................................ 52
11.9 UserSetControl ......................................................................................................................................................... 52
11.10 FlatFieldCorrectionControl ....................................................................................................................................... 53
12 Revision History ......................................................................................................................................................... 54

No.20S062-00
4/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
P
recautions for safety
Please read carefully this “Precautions for safety” before use the camera. Then the camera uses correctly with agreeing
with below notes.
I
n this
“
Precautions for safety
”,
notes divides into
“
Warning
”
and
“
Caution
”
to use the camera safety and prevent to
harm and damage.
Warning This shows, assumption for possibility of serious accident leading death or serious injury if ignore this note and camera uses incorrectly.
Caution This shows, assumption for possibility of bear the damage or physical
damage if ignore this note and camera uses incorrectly.
About Graphic
symbols This symbol shows general prohibition.
This symbol shows completion or instruction.
[Environment / condition]
Warning
Do not use flammable or explosiveness
atmospheres.
This will cause of personal injury or fire.
Do not use for “safety for human body” related
usage.
This camera is designed for use “do not harm
human body immediately” if by any chance the
camera has malfunction.
Caution
Use and store under specified environmental
conditions (Vibration, shock, temperature,
humidity) in the specifications for this camera.
This will cause of fire or damage the camera.
[Installation and cable wiring]
Warning
Do not use with out of power voltage range
that is specified in the specifications for this
camera.
This will cause of fire, electrification or
malfunction.
Do not wrong wiring.
This will cause of fire or malfunction.

No.20S062-00
5/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
Caution
Do not grounding DC power (+) of all devices
that are connect to the camera.
The camera housing is connecting to 0 V line of
camera inside circuit.
There is a risk of short circuit between camera
inside ciurcuit and frame ground.
This will cause of malfunction.
It is necessary to wiring and mounting that is
specified in the specifications for this camera.
This will cause of fire or malfunction.
It is necessary to wiring with turn off the camera.
This will cause of electrification or malfunction.
It is necessary to mounting the camera without
stress for the cable.
This will case of electrification or fire.
Do not use CoaXPress un-supported cable
and board.
There is a risk of malfunction if the camera
connects with wrong environment and turn on
the camera.
[Usage instruction]
Warning
Do not touch the terminal and PCB board
While turn on the camera.
This will cause of electrification or accident
caused by malfunction.
Do not put combustibles near the camera.
This will cause of fire.
Do not use without usage that is specified in
the specifications for this camera.
This will cause of personal injury or malfunction.
Do not push metals including screw driver into
radiation holes.
This will cause of electrification or malfunction.
Do not touch the camera housing while or
afterusing the camera.
There is a risk of get burned.
Caution
Do not push contamination into opening of
the camera.
This will cause of electrification or malfunction.
Do not block the radiation holes.
This will cause of fire due to increase the
camera inside temperature.
[Maintenance]
Caution
Do not disassemble or repair the camera.
This will cause of fire, electrification or
malfunction.
It is turn off the camera when maintaining or
inspecting the camera.
This will cause of electrification.

No.20S062-00
6/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
[Disposal]
Caution
It is necessary to dispose as industrial waste.
It is necessary to dispose of accordance with
WEEE directive.
[Security Measures, Anti-virus protection]
Warning
Install the latest commercial-quality antivirus
software on the computer connected to the
control system and maintain to keep the
software up-to-date.

No.20S062-00
7/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
1 Product Precautions
 Do not give shock to the camera.
 Do not haul or damage the camera cable.
 Do not wrap the camera with any material while using the camera. This will cause the internal camera
temperature to increase.
 When the camera moving or using the place that temperature difference is extreme, countermeasure for dew
condensation (heat removal / cold removal) is necessary.
 While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting
in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.
・ In wet, moist, high humidity or dusty place
・ Under direct sunlight
・ In extreme high or low temperature place
・ Near an object that releases a strong magnetic or electric filed
・ Place with strong vibrations
 Apply the power that satisfies the specified in specifications for the camera.
 The defective pixels may appear due to the sensor characteristics.
 Use below recommend materials (or equivalent materials) to clean the surface of glass.
・ Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)
・ Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)
・ Non-woven: nikowipe clean room (NKB)
 Use a soft cloth to clean the camera.
2 Product conformity / compliance
Please confirm regulation in each country by responsibility of exporter and importer when exporting this product from
Japan.
3 Warranty
■Warranty period
One year after delivery (However, the camera had malfunction with camera uses correctly)
In below case for a fee even within warranty period.
・The malfunction caused by incorrect usage, incorrect modify or repair.
・The malfunction caused by external shock including the camera dropping after delivery the camera.
・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or
wrong voltage.
■Warranty coverage
Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.

No.20S062-00
8/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
4 Overview
This document describes the specifications of the following cameras
STC-LBGP251BCXP124 / STC-LCGP251BCXP124
STC-LBGP251BCXP124-T / STC-LCGP251BCXP124-T
4.1 Features
・CoaXPress (CXP) Interface: CXP-12 / CXP-6 / CXP-3, 4 lane / 2 lane / 1 lane
・PoCXP (Power Over CoaXPress) support
・Maximum frame rate (Full resolution): 150 fps @ 25M 8bits
・CMOS (Global Shutter)
・Up to 2,048 Pixel Defect Correction (Default: ON)
・8bits, 10bits output
4.2 Product Number Naming Method
STC-LxGP251BCXP124-T
251B: 25M, 1.1” high speed sensor
B: Monochrome
C: Color
CXP12: CoaXPress 12.5Gbps (CXP-12)
4: 4 lane
GP: Gpixel CMOS sensor
(none): CXP connectors on rear
T: CXP connectors on top

No.20S062-00
9/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5 Specifications
5.1 Electronic Specifications
Bold: Default
Model Number STC-LBGP251BCXP124 /
S
TC
-
LBGP251BCXP124
-
T
STC-LCGP251BCXP124 /
S
TC
-
LCGP251BCXP124
-
T
Image Sensor 1.1” 25M Progressive Monochrome CMOS
(
Gpixel
:
GMAX0505
)
1.1” 25M Progressive Monochrome CMOS
(
Gpixel
:
GMAX0505
)
Shutter Type Global Shutter
Active Picture Elements 5,120 (H) x 5,120 (V)
Cell Size 2.5 (H) x 2.5 (V) µm
Scanning
System
Full scanning / ROI
Frame Rate
(Full
resolution)
CXP-12 4 Lane 8bits: 150 fps, 10bits: 141 fps
CXP-6 4 Lane 8bits: 86 fps, 10bits: 70 fps
CXP-3 4 Lane 8bits: 43 fps, 10bits: 35 fps
CXP-12 2 Lane 8bits: 86 fps, 10bits: 70 fps
CXP-6 2 Lane 8bits: 43 fps, 10bits: 35 fps
CXP-3 2 Lane 8bits: 21 fps, 10bits: 17 fps
CXP-12 1 Lane 8bits: 43 fps, 10bits: 35 fps
CXP-6 1 Lane 8bits: 21 fps, 10bits: 17 fps
CXP-3 1 Lane 8bits: 10 fps, 10bits: 8 fps
ADC bit width (*1) 10bits
Image Output Format (*1) (*2) Mono8 / Mono10 BayerRG8 / BayerRG10
CoaXPress Data Output CXP-12 (12.500 Gbps) 4 Lane / CXP-6 (6.250 Gbps) 4 Lane / CXP-3 (3.125 Gbps) 4 Lane
CXP-12 (12.500 Gbps) 2 Lane / CXP-6 (6.250 Gbps) 2 Lane / CXP-3 (3.125 Gbps) 2 Lane
CXP
-
12
(
12
.5
00
Gbps)
1
Lane
/
CXP
-
6
(6.25
0
Gbps)
1
Lane
/ CXP
-
3 (3.125 Gbps) 1 Lane
Noise Level 8bits output Less than 4 digits (Gain 0 dB)
10bits output Less than 16 digits (Gain 0 dB)
Sensitivity (*3) 500 Lux 1,000 Lux
Exposure Time 8 µseconds to 16.777 seconds (Default: 6.626 µseconds)
Gain Analog x1.5 / x2 / x2.5 (Default: x2.5)
Digital x1 to x7 (Default: x1)
Black Level 8bits: 0 to 31 digits (Default: 10)
10bits: 0 to 127 digits
White Balance Gain N/A 0 (Black Level) to x7.98 (Default: x1)
ROI Horizontal: 256 to 5,120 pixels / Vertical: 4 to 5,120 lines (Default: 5,120 x 5,120)
Adjustable Steps for size: 8 pixels in horizontal direction / 2 lines in vertical direction
Adjustable Steps for offset: 2 pixels in horizontal direction / 2 lines in vertical direction
Multi ROIs
Eight Regions (Horizontal 1 x Vertical 8 regions)
(Default: One region)
Gamma
Gamma
0.
0
1 to 4.0
0
(
Default
: 1
.0
0
)
Binning
2
x
2 /
Off
N/A
Decimation
1/2 x 1/2,
Off
Image Flip Horizontal / Vertical / Horizontal and Vertical / Off
FFC (Flat Field Correction) Support
Defective Pixel Correction Up to 2,048 points
Auto Image
Control
Auto Exposure
N/A
Auto Gain
N/A
Auto White Balance
N/A
Off / Once
/ Continuous / Disable
Operational Mode Edge Preset Trigger / Pulse Width Trigger / CXP Tigger Packet / Free Run
Interface CoaXPress
Protocol CoaXPress Standard Version 2.0 and GenICam SFNC 2.6 compliant
I/O 4 GPIOs
Power Input Voltage PoCXP (+18.5 to +26 Vdc) / External power (+18.5 to +26 Vdc)
Consumption Maximum: Less than 10.5 W, Typical: 9.3 W

No.20S062-00
10/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
Precautions
(*1) When Image Format is changed, ADC bits width also changes.
The ADC bits width cannot be changed.
Image Format ADC bits width
Mono8 / BayerRG8 -> 10bits
Mono10 / BayerRG10 -> 10bits
(*2) The pixel format (Bayer pattern) for color model is changed when image is flipping with image flip function.
The Bayer pattern in this document is Bayer pattern of image flip function Off.
(*3) The sensitivity is measuring the luminance when white level achieved 100 % in below conditions.
Camera Setting Environment
Parameter Setting Parameter Setting
Gain Up Factory Setting Light Source Light Box (White)
AGC Off Color temperature 5,100K
White Balance Optimum Lens
Electrical Shutter 1/30 seconds F on Lens F5.6
Black Level Optimum Target Luminance IM-600 (Topcon)
Gamma Factory Setting

No.20S062-00
11/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5.2 Spectral Sensitivity Characteristics

No.20S062-00
12/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5.3 Mechanical Specifications
(*1) Excluding connectors
Model Number STC-LBGP251BCXP124 /
S
TC
-
L
C
GP251BCXP124
STC-LBGP251BCXP124-T /
S
TC
-
LCGP251BCXP124
-
T
Dimensions 68 (W) x 68 (H) x 53.5 (D) mm (*1)
Optical Filter No Optical Filter
Optical Center Accuracy Positional accuracy in Horizontal and Vertical directions: +/- 0.5 mm
Rotational accuracy of Horizontal and Vertical: +/
-
1.5 deg.
Material Aluminum alloy
Lens Mount C Mount
Interface Connector CXP connector: Micro BNC, 75 Ohm x 4
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent x 1
Camera Mounting Twenty M4 screw holes
(Four on Front, top, bottom and both side plates)
Eighteen M4 screw holes
(Two on top, Four on Front, bottom and
both side plates)
Weight Approximately 460 g

No.20S062-00
13/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5.4 Environmental Specifications
(*1) Please insure the camera is installed with appropriate heat dissipation to keep camera housing temperature
(top plate) is less than +60 deg. C when camera using ambient temperature is exceeded +37 deg. C.
If the camera has a mounted lens and a tripod with an aluminum plate, this could decrease camera housing
temperature for heat dissipation.
When the internal temperature sensor (Device Temperature Selector = Sensor) on the camera shows less than
+65 deg. C, the camera housing temperature (top plate) will be less than +60 deg. C.
Upper side of camera
STC-LxGP251BCXP124 STC-LxGP251BCXP124-T
Model Number STC-LBGP251BCXP124
STC
-
LCGP251B
CXP
124
STC-LBGP251BCXP124-T
STC
-
L
C
GP251B
CXP
124
-
T
Operational
Temperature /
Humidity
Minimum Environmental Temperature: 0 deg. C,
Environmental Humidity: 20 to 85 %RH (No Condensation)
Maximum Environmental Temperature: +37 deg. C or
Camera housing temperature (top plate) shall not exceed +60 deg. C (*1)
Environmental Humidity: 20 to 85 %RH (No Condensation)
Storage Temperature /
Humidity
Environmental Temperature: -20 to +75 deg. C,
Environmental Humidity: 20 to 85%RH (No Condensation)
Vibration 20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10G, XYZ 3 directions 30 min. each
Shock Acceleration 38 G, half amplitude 6 mseconds, XYZ 3 directions 3 times each
Standard Compliancy EMS: EN61000-6-2:2005, EMI: EN61000-6-4:2007+A1:2011
RoHS RoHS Compliance
Measuring point

No.20S062-00
14/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5.5 External Connector Specifications
STC-LxGP251BCXP124 STC-LxGP251BCXP124-T
5.5.1 Micro BNC Connector
Micro BNC, 75 Ohm or equivalent x 4
This camera is PoCXP supported CoaXPress camera.
The CoaXPress frame grabber board is supplied power to camera through Micro BNC connector.
Please using CXP12 supported cable.
When CH1 was connected to Frame Grabber (FG), FG provides power to camera through PoCXP. Some FG
starts discovery CXP camera when CH1 was connected. If CH1 connecting first, camera may recognize as
CXP12, CXP6 or CXP3 (12.5Gbps, 6.25Gbps or 3.125Gbps) 1 Lane configuration.
To recognize as CXP12, CXP6 or CXP3 2 Lane or 4 Lane configurations, please connect CH1 after connected
from CH2 to CH4, or re-discovery after all CH is connected.
Micro BNC
Connector
Power/IO
Connector
Micro BNC
Connector
Power/IO
Connector

No.20S062-00
15/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5.5.2 Power/IO Connector
HR10A-7R-6PB (Hirose) or equivalent.
This connector is for external power supply and, input and output signals.
As for the cable part (Female connector), HR10A-7P-6S (Hirose) or equivalent can be used.
Pin assignment
Output signal selection for Line 0 to 3
The output signal can be selectable from below:
GenICam
Off
User Output
Trigger Out
Trigger Through Out
Exposure End Out
Frame End Out
Frame Trigger Wait
Transfer End Out
Sensor Read Out
Strobe Out
Exposure Active
Pin No. Signal Name IN/OUT Signal Voltage
1 GND IN 0 V
2 Line3 IN/OUT +3.3 V
3 Line2 IN/OUT +3.3 V
4 Line1 IN/OUT +3.3 V
5 Line0 IN/OUT +3.3 V
6 +24 V IN +24 V

No.20S062-00
16/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
● Block diagram of IO connector
Camera IO interface
3.3VLVCOMS or LVTTL
(FPGA SIDE)
dir cont
(input)
100
Ω
10k
Ω
3.3V 3.3V
or
Nch MOSFET
Open Drain
INPUT High Level : 2.0V
～
3.3V
INPUT Low Level : 0V
～
0.8V
(FPGA SIDE)
dir cont
(output)
100
Ω
10k
Ω
3.3V 3.3V
OUTPUT High min : 2.3V
OUTPUT Low max : 0.7V
3.3VLVCOMS or LVTTL
Recommended interface circuit

No.20S062-00
17/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
5.5.3 Connector indicator lamp
Connector indicator LED exists beside of Micro BNC connector.
LED informs status of communication. The detail of status is as following table.
Status
LED
Blinking
Pattern
No power Off
System booting Solid orange
Device / Host no connection When using PoCXP: : (No such case)
When using external power: : Slow flash red
Detecting Device / Host connection When using PoCXP: : Fast flash alternating green / orange
When using external power: : Fast flash orange
Device / Host connecting Failed When using PoCXP: : Slow flash alternating red / green
When using external power : Slow flash alternating red / orange
Device / Host connected,
but no data being transferred
Solid green
Device / Host connected,
waiting for trigger
Slow flash orange
Device / Host connected,
data being transferred
Fast flash green
Device / Host connected,
data transferring error
Solid red (500 mseconds)
Device / Host connected,
while sending Test Packet
Slow flash alternating green / orange
System Error Fast flash red

No.20S062-00
18/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
6 Dimensions
6.1 STC-LBGP251BCXP124 / STC-LCGP251BCXP124
Unit: mm

No.20S062-00
19/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
6.2 STC-LBGP251BCXP124-T / STC-LCGP251BCXP124-T
Unit: mm

No.20S062-00
20/55
STC-LBGP251BCXP124 / STC-LCGP251BCXP124 / STC-LBGP251BCXP124-T / STC-LCGP251BCXP-T
Product Specifications and User’s Guide
7 Sensor Information
7.1 Pixel Transferring Image
STC-LBGP251BCXP124 / STC-LBGP251BCXP124-T (Monochrome)
Pixel 1
of Data
Pixel 2
of Data
Pixel (n) of Data: nth pixel being transferred
STC-LCGP251BCXP124 / STC-LCGP251BCXP124-T (Color)
Pixel 21
of Data
Pixel 22
of Data
Pixel 11
of Data
Pixel 12
of Data
Pixel (m, n) of Data: nth pixel of mth line being transferred