Omron STC-MBS163POE User manual

No.18S109-02
1/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
GigE Vision
Monochrome / Color CMOS PoE Camera
STC-MBS163POE (1.6M / Monochrome)
STC-MCS163POE (1.6M / Color)
Product Specifications and User’s Guide

No.18S109-02
2/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
Table of Contents
1 Product Precautions ............................................................................................ 8
2 Warranty ................................................................................................................ 8
3 Software Licensing .............................................................................................. 9
3.1 LWIP TCP/IP Licensing ............................................................................................................ 9
4 Introduction ........................................................................................................ 10
4.1 Features .................................................................................................................................. 10
4.2 Naming Method ...................................................................................................................... 10
5 Specifications ...................................................................................................... 11
5.1 Electronic Specifications ....................................................................................................... 11
5.2 Spectral Sensitivity Characteristics ..................................................................................... 13
STC-MBS163POE ............................................................................................................................ 13
STC-MCS163POE (without IR Cut Filter) ....................................................................................... 13
IR Cut Filter (STC-MCS163POE) ..................................................................................................... 14
5.3 Mechanical Specifications ..................................................................................................... 14
5.4 Environmental Specifications ............................................................................................... 15
6 Connector Specifications .................................................................................. 16
6.1 RJ45 Connector ...................................................................................................................... 16
6.2 Power and Control Signal Connector ................................................................................... 17
Opto-isolated input ......................................................................................................................... 19
Opto-isolated output ....................................................................................................................... 19
Open Collector GPIO ...................................................................................................................... 20
Input and Output Signal Timing (Hardware Trigger) ..................................................................... 21
Input and Output Signal Timing (Software Trigger) ...................................................................... 22
External Hardware Trigger Input Delay.......................................................................................... 23
6.2.6.1 External Trigger Signal Delay (Positive polarity trigger signal)................................................ 23
6.2.6.2 External Trigger Signal Delay (Negative polarity trigger signal) .............................................. 23
6.2.6.3 Measured External Trigger Signal Delay through Opt-Isolated Port (Line 0) ........................... 24
6.2.6.4 Measured External Trigger Signal Delay through Open Collector GPIO Port (Line 2) ............ 25

No.18S109-02
3/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
7 Dimensions ......................................................................................................... 26
7.1 STC-MBS163POE ................................................................................................................... 26
7.2 STC-MCS163POE ................................................................................................................... 27
8 Sensor Information ............................................................................................ 28
8.1 Pixel Transferring Image ........................................................................................................ 28
9 Camera Operational Modes ............................................................................... 29
9.1 Normal Mode ........................................................................................................................... 29
9.2 Pulse width trigger mode....................................................................................................... 30
Timing .............................................................................................................................................. 30
Exposure Timing with Positive Polarity Trigger Signal ................................................................ 31
Exposure Timing with Negative Polarity Trigger Signal ............................................................... 32
9.3 Edge Preset Trigger Mode ..................................................................................................... 33
Timing .............................................................................................................................................. 33
Exposure Timing with Positive Polarity Trigger Signal ................................................................ 34
Exposure Timing with the Negative Polarity Trigger signal ......................................................... 34
9.4 Edge Preset Trigger Mode (Trigger input while image is out) ............................................ 35
Timing .............................................................................................................................................. 35
10 Camera Functions .............................................................................................. 36
10.1 Save and load the camera settings .................................................................................... 36
Saving Camera Settings .............................................................................................................. 36
Loading Camera Settings ............................................................................................................ 37
Loading Camera Settings when Camera Power is on ............................................................... 37
Camera Settings Initialization ..................................................................................................... 37
10.2 Frame rate ............................................................................................................................ 38
10.3 Gain ...................................................................................................................................... 38
Analog Gain ................................................................................................................................. 38
Digital Gain ................................................................................................................................... 38
10.4 Exposure Time ..................................................................................................................... 39
10.5 Black Level ........................................................................................................................... 39
10.6 ALC (Auto Light Control) .................................................................................................... 40

No.18S109-02
4/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
ALC control method .................................................................................................................... 41
AGC (Auto Gain Contorl) ............................................................................................................. 42
Auto shutter ................................................................................................................................. 43
ALC settings procedure .............................................................................................................. 43
10.7 White balance (Only available for color camera) .............................................................. 44
White balance control methods .................................................................................................. 44
White balance control method selection .................................................................................... 44
White balance calculate region setting ...................................................................................... 46
10.8 Gamma correction ............................................................................................................... 47
10.9 ROI (Region of Interest) ...................................................................................................... 47
10.10 Pixel Format ...................................................................................................................... 48
10.11 Binning (Only STC-MBS163POE) ....................................................................................... 48
10.12 Decimation ........................................................................................................................ 49
10.13 Trigger ............................................................................................................................... 50
Trigger signal processing procedure ......................................................................................... 50
10.14 Image Flip .......................................................................................................................... 51
10.15 LUT Control ....................................................................................................................... 51
10.16 Defective pixel correction ................................................................................................ 52
10.17 Counter And Timer Control ............................................................................................. 53
10.18 Event Control .................................................................................................................... 54
10.19 Chunk Control .................................................................................................................. 55
10.20 Action Control .................................................................................................................. 55
10.21 IEEE1588 ........................................................................................................................... 56
11 GenICam command ............................................................................................ 58
11.1 DeviceControl ...................................................................................................................... 58
11.2 ImageFormatControl ........................................................................................................... 60
11.3 AcquisitionControl .............................................................................................................. 61
11.4 AnalogControl ..................................................................................................................... 62
11.5 LUTControl ........................................................................................................................... 63

No.18S109-02
5/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
11.6 DigitalIOControl ................................................................................................................... 63
11.7 LogicBlockControl .............................................................................................................. 64
11.8 SoftwareSignalControl ........................................................................................................ 64
11.9 CounterAndTimerControl ................................................................................................... 64
11.10 EventControl ........................................................................................................................ 65
11.11 UserSetControl .................................................................................................................... 65
11.12 ChunkDataControl ............................................................................................................... 66
11.13 ActionControl ...................................................................................................................... 66
11.14 FileAccessControl ............................................................................................................... 67
11.15 Test Control ......................................................................................................................... 67
11.16 TransportLayerControl ....................................................................................................... 68
12 Revision History ................................................................................................. 70

No.18S109-02
6/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
Precautions for safe use
Please read carefully this “Precautions for safe use” before use the camera. Then the camera uses correctly with
agreeing with below notes.
In this “Precautions for safe use”, notes divides into “Warning” and “Caution” to use the camera safety and prevent to
harm and damage.
Warning This shows, assumption for possibility of serious accident leading death or
serious injury if ignore this note and camera uses incorrectly.
Caution This shows, assumption for possibility of bear the damage or physical
damage if ignore this note and camera uses incorrectly.
About Graphic
symbols This symbol shows general prohibition.
This symbol shows completion or instruction.
[Environment / condition]
Warning
Do not use flammable or explosiveness
atmospheres.
This will cause of personal injury or fire.
Do not use for “safety for human body” related
usage.
This camera is designed for use “do not harm
human body immediately” if by any chance the
camera has malfunction.
Caution
Use and store under specified environmental
conditions (Vibration, shock, temperature,
humidity) in the specifications for this camera.
This will cause of fire or damage the camera.
[Installation and cable wiring]
Warning
Do not use with out of power voltage range
that is specified in the specifications for this
camera.
This will cause of fire, electrification or
malfunction.
Do not wrong wiring.
This will cause of fire or malfunction.

No.18S109-02
7/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
Caution
The camera housing and 0 V line of camera
inside circuit are isolated.
There is a risk of short circuit between camera
inside ciurcuit and frame ground through other
devices.
This will cause of malfunction.
It is necessary to wiring and mounting that is
specified in the specifications for this camera.
This will cause of fire or malfunction.
It is necessary to wiring with turn off the camera.
This will cause of electrification or malfunction.
It is necessary to mounting the camera without
stress for the cable.
This will case of electrification or fire.
[Usage instruction]
Warning
Do not touch the terminal and PCB board
While turn on the camera.
This will cause of electrification or accident
caused by malfunction.
Do not put combustibles near the camera.
This will cause of fire.
Do not use without usage that is specified in
the specifications for this camera.
This will cause of personal injury or malfunction.
Do not push metals including screw driver into
radiation holes.
This will cause of electrification or malfunction.
Do not touch the camera housing while or
afterusing the camera.
There is a risk of get burned.
Caution
Do not push contamination into opening of
the camera.
This will cause of electrification or malfunction.
Do not block the radiation holes.
This will cause of fire due to increase the
camera inside temperature.
[Maintenance]
Caution
Do not disassemble or repair the camera.
This will cause of fire, electrification or
malfunction.
It is turn off the camera when maintaining or
inspecting the camera.
This will cause of electrification.
[Disposal]
Caution
It is necessary to dispose as industrial waste.
]

No.18S109-02
8/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
1 Product Precautions
 Do not give shock to the camera.
 Do not haul or damage the camera cable.
 Do not wrap the camera with any material while using the camera. This will cause the internal camera
temperature to increase.
 When the camera moving or using the place that temperature difference is extreme, countermeasure for dew
condensation (heat removal / cold removal) is necessary.
 While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting
in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.
・ In wet, moist, high humidity or dusty place
・ Under direct sunlight
・ In extreme high or low temperature place
・ Near an object that releases a strong magnetic or electric filed
・ Place with strong vibrations
 Apply the power that satisfies the specified in specifications for the camera.
 The defective pixels may appear due to the sensor characteristics.
 Use below recommend materials (or equivalent materials) to clean the surface of glass.
・ Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)
・ Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)
・ Non-woven: nikowipe clean room (NKB)
 Use a soft cloth to clean the camera.
2 Warranty
■Warranty period
One year after delivery (However, the camera had malfunction with camera uses correctly)
In below case for a fee even within warranty period.
・The malfunction caused by incorrect usage, incorrect modify or repair.
・The malfunction caused by external shock including the camera dropping after delivery the camera.
・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or
wrong voltage.
■Warranty coverage
Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.

No.18S109-02
9/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
3 Software Licensing
3.1 LWIP TCP/IP Licensing
The software in this camera includes LWIP TCP/IP implementation.
The copyright information is
Copyright (c) 2001-2004 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.

No.18S109-02
10/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
4 Introduction
This document describes the specification of the following cameras:
STC-MBS163POE / STC-MCS163POE
4.1 Features
 GigE Interface
 Support PoE (Power over Ethernet)
 Small robust camera housing
 Maximum frame rate (Full resolution): 70.7 fps @ 1.6M 8bits
 CMOS (Global Shutter)
 Up to 2,048 Defective Pixel Correction (Default: ON)
 8bits, 10bits, 12bits output
4.2 Naming Method
STC-MxS163POE
B: Monochrome
C: Color
POE: PoE (Power over Ethernet (Gigabit Ethernet))
Sensor Manufacture
S: SONY
163: 1/2.9”, 1.6M Sensor

No.18S109-02
11/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
5 Specifications
5.1 Electronic Specifications
Product STC-MBS163POE STC-MCS163POE
Image Sensor 1/2.9” 1.6M Progressive Monochrome CMOS
(SONY: IMX273)
1/2.9” 1.6M Progressive Color CMOS
(SONY: IMX273)
Shutter Type Global Shutter
Active Picture Elements 1,440 (H) x 1,088 (V)
Cell Size 3.45 (H) x 3.45 (V) µm
Sync System External trigger (Hardware / Software) / Free run
Scanning Mode Full scanning (Full resolution) / ROI
Frame rate (at full scanning) 8bits: 70.7 fps / 10bits: 35.3 fps / 10bits Packed: 47.1 fps /
12bits: 35.3 fps / 12bits Packed: 47.1 fps / RGB8: 23.5 fps
Maximum frame rate: 1,762.82 fps @ 4 lines (8bits)
ADC bit depth 12bits
Image Output Format Mono8 / Mono10 / Mono10Packed /
Mono12 / Mono12Packed
Mono8 / Mono10 / Mono10Packed /
Mono12 / Mono12Packed /
BayerRG8 / BayerRG10 / BayerRG10Packed /
BayerRG12 / BayerRG12Packed / RGB8
Noise
Level
8bits output Less than 2.8 digits (Gain 0 dB)
10bits / 10bits Packed output Less than 11.2 digits (Gain 0 dB)
12bits / 12bits Packed output Less than 44.8 digits (Gain 0 dB)
Sensitivity (*1) 365 Lux 460 Lux
Exposure Time 1 µseconds to 16.777 seconds (Default: 13,936 µseconds)
Gain Analog Gain 0 to 20.8 dB (Default: 0 dB)
Digital Gain x1 to x3 (Default: x1)
ROI Horizontal: 264 to 1,440 pixels, Vertical: 4 to 1,080 lines (Default: 1,440 x 1,080)
Adjustable steps for size: 8 pixels in horizontal direction and 4 lines in vertical direction
Adjustable steps for offset: 8 pixels in horizontal direction and 4 lines in vertical direction
Gamma Gamma 0.1 to 4.0 (Default: 1.0)
Binning Horizontal and Vertical binning (2x2) / Off N/A
Decimation Horizontal and Vertical decimation (2x2) / Off
Image Flip Horizontal / Vertical / Horizontal and Vertical / Off
Defective Pixel Correction Up to 2,048 points (Default: On)
Auto
Image
Control
Auto Exposure Support (Default: OFF)
Auto Gain Support (Default: OFF)
Auto White Balance N/A Auto / Manual / Push to Set
Operational Mode Edge preset trigger / Pulse width trigger / Free run
Interface PoE: IEEE802.3af CLASS2 (1000BASE-T)
Protocol GigE Vision 2.1 and GenICam SFNC 2.4, IEEE1588 (PTP)
I/O One opto-isolated input, one opto-isolated output and one open collector GPIO (Input or output)
Power Input Voltage (*2) +10.8 to +26.4 Vdc External power (via 6 pin connector) /
Power Over Ethernet (IEEE802.3af)
Consumption +12 V / +24 V: 3.6 W, PoE: 4.4 W
Default: Bold

No.18S109-02
12/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
Precautions
(*1) The sensitivity is measuring the luminance when white level achieved 100 % in below conditions.
(*2) The camera operates with external power when power suppling by external power supply and PoE to camera
at same time.
Camera Setting Environment
Parameter Setting Parameter Setting
Gain Up 0 dB Light Source Light Box (White)
AGC Off Color temperature 5,100K
White Balance Optimum Lens
Electrical Shutter 1/30 seconds F on Lens F5.6
Black Level Optimum Target Luminance IM-600 (Topcon)
Gamma Factory Setting

No.18S109-02
13/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
5.2 Spectral Sensitivity Characteristics
STC-MBS163POE
STC-MCS163POE (without IR Cut Filter)

No.18S109-02
14/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
IR Cut Filter (STC-MCS163POE)
5.3 Mechanical Specifications
Model Number STC-MBS163POE STC-MCS163POE
Dimensions 29 (W) x 29 (H) x 53 (D) mm (*1)
Optical Filter No Optical Filter IR Cut Filter
Optical Center Accuracy Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 1.5 deg.
Material Aluminum Alloy (AC)
Lens Mount C mount
Interface Connectors Ethernet connector: RJ45 connector
Power- I/O connector: HR10A-7R-6PB (Hirose) or equivalent
Camera Mounting Six M3 screw holes (Two on top, four on bottom plate)
Weight Approximately 65 g
(*1) Excluding the connectors

No.18S109-02
15/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
5.4 Environmental Specifications
Model Number STC-MBS163POE STC-MCS163POE
Operational
Temperature /
Humidity
Minimum Environmental Temperature: 0 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Maximum Environmental Temperature: +39 deg. C or
Camera housing temperature (top plate) shall not exceed +64 deg. C (*1)
Environmental Humidity: 0 to 85 %RH (No condensation)
Storage Temperature / Humidity Environmental Temperature: -20 to +70 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation)
Vibration 20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G, XYZ 3 directions, 30 min. each
Shock Acceleration 38 G, half amplitude 6 ms, XYZ 3 directions, 3 times each
Standard Compliancy EMS: EN61000-6-2, EMI: EN55011
RoHS RoHS Compliance
(*1) Please insure the camera is installed with the appropriate heat dissipation. If camera has a mounted lens and a tripod
with an aluminum plate, this could decrease the camera housing temperature for heat dissipation. When the internal
temperature sensor on the camera shows less than 74 deg. C, the camera housing temperature (top plate) will be less than
64 deg. C.
Taking these steps will maintain the heat rating of the electronic components of the camera.
Upper side of camera
Measuring point

No.18S109-02
16/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
6 Connector Specifications
6.1 RJ45 Connector
This product is PoE compliant.
Please supply power (+10.8 to +26.4 Vdc) through the power-I/O connector when using non-PoE-compliant
NIC.
Pin Assignment LED
Pin No. Signal Name
1 TA+
2 TA-
3 TB+
4 TC+
5 TC-
6 TB-
7 TD+
8 TD-
Please use a 1GB supported NIC, Network Switcher and Ethernet cable.
Check the setting of NIC and Network Switcher being used is “1GB transferring”.
Green LED Yellow LED Status
Green Light ON Yellow Light OFF Power ON (1GB NIC)
Green Light OFF Yellow Light OFF Power ON (100MB NIC)
Green Light ON Yellow Light Blinking 1 GB Transferring
Green Light OFF Yellow Light Blinking 100 MB Transferring
Camera is powered-on Green light: ON
Yellow light: Blinking
1 GB Transferring
Green light: OFF
Yellow light: Blinking
100 MB Transferring
Power-I/O Connector
RJ45 Connector
Yellow LED Green LED

No.18S109-02
17/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
6.2 Power and Control Signal Connector
HR10A-7R-6PB (Hirose) or equivalent
This connector is for the power supply and input / output signals.
The power from this connector is priority power for camera when power supplies through this connector and
PoE at same time.
Please use HR10A-7P-6S (Hirose) or equivalent for cable.
Pin assignment
Configuration of Line2 (Pin No.3) and Line1 (Pin No.4)
Output signal can be assign by GenICam command.
.
Pin No. Signal Name IN / OUT Voltage
1 POWER IN IN +10.8 to +26.4 Vdc
2 Opto-isolated in
(Line0)
IN Low: Smaller than +1.0 V
High: +3.0 to +26.4 V
* Potential difference between
TRG_in and Opt. Isolated Common
3 Open Collector
GPIO
(Line2)
IN / OUT +3.0 to +26.4 V / Open Collector
4 Opto-isolated out
(Line1)
OUT Open Collector
5 Opto-isolated
Common
IN
6 GND IN 0 V
GenICam
1) Frame Trigger Wait (Default for all output)
2) Frame Trigger Internal
3) Exposure Active
4) Acquisition Trigger Wait
5) Acquisition Trigger Internal
6) Sensor Read Out
7) Debounced Line 0
8) Debounced Line 2
9) User Output 1
10) User Output 2
11) Timer 0 Active
12) Software Signal 0
13) Software Signal 1
14) Logic Block 0
15) Pulse Per Second

No.18S109-02
18/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
1) Frame Trigger Wait
The condition of camera operation with trigger signal can be check.
“LOW” state of signal is out between “start exposing” to “image out”.
2) Frame Trigger Internal
The input trigger signal with the trigger delay (camera internal process delay).
3) Exposure Active
While camera exposing, “HIGH” state of signal is out. The signal state will be “LOW” after finish
exposing.
4) Acquisition Trigger Wait
While image transferring from camera to PC, “Low” state of signal is out. The signal state will be
“High” after finish image transferring.
5) Acquisition Trigger Internal
The image transferring starts signal is out.
6) Sensor Read Out
FVAL (Frame valid, HIGH state) signal is out.
7) Debounced Line0
Debounced Line0 signal is out.
8) Debounced Line2
Debounced Line2 signal is out.
9) User Output 1 (User Output signal through Line 1)
Selected “HIGH” or “LOW” state of signal is out.
10) User Output 2 (User Output signal through Line 2)
Selected “HIGH” or “LOW” state of signal is out.
11) Timer 0 Active
Selected signal at “Timer Counter” is out.
When signal synchronizing with “Exposure Active” signal, signal can use for strobe control.
12) Software Signal 0
Selected signal for “Software Signal 0” at “Software Signal Control” is out.
13) Software Signal 1
Selected signal for “Software Signal 1” at “Software Signal Control” is out.
14) Logic Block 0
“Logic Block 0” signal is out.
15) Pulse Per Second
“Pulse / second” signal (50% Duty, 1 Hz interval) is out.

No.18S109-02
19/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
Opto-isolated input
The camera has current limiting circuit on camera. The current limiting resistor does not necessary.
Opto-isolated output
It is necessary to have current limiting resistor at outside of camera, to keep less than 50 mA.

No.18S109-02
20/71
STC-MBS163POE / STC-MCS163POE
Product Specifications and User’s Guide
Open Collector GPIO
This GPIO can be used for input or output.
When using as output, it is necessary to have current limiting resistor at outside of camera, to keep current
less than 50 mA.
When using as input, current limiting resistor does not necessary. However, camera does not have current
limiting circuit on camera. The camera inside circuit may get damage if accidentally uses as output without
current limiting resistor. For safety, please add current limiting resistor even use as input.
a) Open Collector GPIO uses as output
b) Open Collector GIPO uses as input