Omron SYSDRIVE 3G3MV SERIES User manual

3G3MV
quick start guide
020 8450 8087
020 8450 0173
www.omron.co.uk
[email protected]
1 Apsley Way, Staples orner, London, NW2 7HF
Fax number
020 8233 1468
Factory automation technical support
24hr technical helpsheet/datasheet faxback service
020 8450 4646
General telephone enquiries and technical support
UK website
irect e-mail address for sales enquiries

M
L1
L2
L3
R/L1
S/L2
T/L3
3-phase 200 V A , single-phase
200 V AV or 3-phase 400 V A
(See Note 1)
Noise Filter lamp core
Braking Resister
(optional)
B1 B2
U/T1
V/T2
W/T3
S1
S2
S3
S4
S5
S6
S7
MA
MB
MC
NO
SC
FS
FR
FC
RP
P1
P2
PC
AM
ommon
Multi-function
photocoupler output 1
Multi-function
photocoupler ouput 2
Multi-function
photocoupler output
common
Multi-function analog output
common
Multi-function analog
output/Pulse monitor
output
1
2
3
CN2
onnector
Digital Operator
Multi-function analog voltage input
Multi-function analog current input
Analog input common
R+
R-
S+
S-
AC
(See Note 2)
}
Multi-function input 1
Multi-function input 2
Multi-function input 3
Multi-function input 4
Multi-function input 5
Multi-function input 6
Multi-function input 7
Sequence input common
Frequency reference power
supply 20mA at +12V
Frequency reference input
Frequency reference common
Pulse train input
3G3MV PFI
Multi-function contact output
NC
L1í
L2í
L3í
Note: onnector on N2 wiring side:
3G3MV P N- N2
RS-422
communications
RS-485 selection
Pulse
generator
External frequency
adjuster
(2 kΩ 1/4 W min.)
3G3IVPF00C/
Standard Connections
Note 1: onnect single-phase 200 V A to terminals R/L1 and S/L2 of the 3G3MV-AB.
Note 2: By using pin 2 of SW2, voltage input or current input can be selected as a frequency reference input.

Multi-function input 1 (Forward/Stop)
Multi-function input 2 (Reverse/ Stop)
Multi-function input 3 (External fault: Normally open)
Multi-function input 4 (Fault reset)
Multi-function input 5 (Multi-step speed reference 1)
Multi-function input 6 (Multi-step speed reference 2)
Multi-function input 7 (Inching frequency command)
Sequence input common
Frequency reference power supply output
Frequency reference input
Frequency reference common
Pulse train input
Multi-function contact output (Normally open: Fault)
Multi-function contact output (Normally closed: Fault)
Multi-function contact output common
Multi-function photocoupler output 1 (During Operation)
Multi-function photocoupler output 2 (At Speed)
Multi-function photocoupler output common
Multi-function analog output (Output Freq.)
Multi-function analog output common
Photocoupler 8mA at 24 V
D (See note 2,3)
20mA at 12 V D
0 to 10 V D (20W)
Response frequency:
0 to 33 kHz (30% to 70% ED)
H: 3.5 to 13.2 V
L: 0.8 V max.
Relay output
1A max. at 30 V D
1A max. at 250 V D
Open collector output
50mA max. at 48 V D
2mA max. at 0 to 10 V D
S1
S2
S3
S4
S5
S6
S7
S
FS
FR
F
RP
MA
MB
M
P1
P2
P
AM
A
Input
Output
Control Circuit Terminals
Symbol Name Specification
Note 1: Functions in parentheses are default settings
Note 2: To provide an external power supply and wire the terminals through a common positive line, set SW1 to
PNP and use a 24 V D + 10% power supply
Note 3: NPN is the default setting for these terminals. However by using SW1, NPN or PNP input can be
selected as shown below.
360
24V
SW1
GND
GND
S
S1 to 7
3.3k
0.1
µ
(Default setting)
GND
S
360
SW1
24V
S1 to 7
24 V D 3.3k
GND
(±10%)
0.1 µ
NPN PNP

L
169
169
174
174
169
169
174
304
W
71
111
144
175
111
111
144
184
H
45
50
50
50
45
45
50
56
X
156
156
161
161
156
156
161
288
Y
51
91
120
150
91
91
120
150
d
M5
M5
M5
M5
M5
M5
M5
M6
Model
3G3MV
AB001
AB002
AB004
AB007
AB015
AB022
AB040
A4002
A4004
A4007
A4015
A4022
A4030
A4040
A4055
A4075
Filter
3G3MV
PFI1010-E
PFI1020-E
PFI1030-E
PFI1040-E
PFI3005-E
PFI3010-E
PFI3020-E
PFI3030-E
Installation
imensions
Rated
Voltage
Model
3G3MV-
Supply Recommendations
Noise Filter Specifications
Y
W
X
d
H
L
D
8.5
Four, 5 dia.
H1 H
W1
W
H
128
128
128
128
128
128
128
128
128
128
128
128
128
128
260
260
H1
118
118
118
118
118
118
118
118
118
118
118
118
118
118
244
244
W
68
68
68
108
108
140
170
108
108
108
108
108
140
140
180
180
W1
56
56
56
96
96
128
158
96
96
96
96
96
128
128
164
164
76
76
131
140
156
163
180
92
110
140
156
156
143
143
170
170
AB001
AB002
AB004
AB007
AB015
AB022
AB040
A4002
A4004
A4007
A4015
A4022
A4030
A4040
A4055
A4075
Single Phase
200 VA
3-Phase
400 VA
MCCB (A)
5
5
10
20
20
40
50
5
5
5
10
10
20
20
30
30
Wire (mm2)
2
2
2
3.5
5.5
5.5
8
2
2
2
3.5
3.5
5.5
5.5
5.5
5.5

Displays relevant data items, such as frequency reference,
output frequency and parameter set values.
Sets the frequency reference within a range between 0Hz
and the maximum frequency.
The frequency reference can be monitored or set while this
indicator is lit.
The output frequency of the Inverter can be monitored or
set while this indicator is lit.
The output current of the inverter can be monitored while
this indicator is lit.
The values set in U01 through U18 are monitored while
this indicator is lit.
The direction of rotation can be selected while this indicator
is lit when operating the Inverter with the RUN Key.
The operation of the Inverter through the Digital Operator
or according to the set parameteres is selectable while this
indicator is lit.
Note: The status of this indicator can be only monitored
while the Inverter is in operation. Any RUN
command input is ignored while this indicator is lit.
The parameter in n01 through to n179 can be set or moni-
tored while this indicator is lit.
Note: While the Inverter is in operation, the parameters
can be only monitored and only some parameters
can be changed. Any RUN command input is
ignored while this indicator is lit.
Switches the setting and monitor item indicators in
sequence.
Parameter being set will be cancelled if this key is pressed
before entering the setting.
Increases multi-function monitor numbers, parameter num-
bers and parameter set values.
Decreases multi-function monitor numbers, parameter
numbers and parameter set values.
Enters multi-function monitor numbers, parameter numbers
and internal data values after they are set or changed.
Starts the Inverter running when the 3G3MV is in operation
with the Digital Operator.
Stops the Inverter unless parameter n007 is not set to
disable the STOP Key.
Data display
FREQ adjuster
FREF indicator
FOUT indicator
IOUT indicator
MNTR indicator
F/R indicator
LO/RE indicator
PRGM indicator
Mode Key
Increment Key
Decrement Key
Enter Key
RUN Key
STOP/RESET Key
Appearance Name Function
IGITAL OPERATOR
PJVOP 140
MIN MAX
FREQUENCY
FREF FOUT IOUT MNTR
F/R LO/RE PRGM
RUN
STOP
RESET
Data display
Keys
Indicators
(Setting/Monitor
item indicators) FREQ adjuster

Parameter Access:
1 - Limited Parameter access
4 - Full Parameter access
8 - Factory Parameter Initialise
RUN command selection:
0 - Stop/Reset key or Keypad enabled
1 - Multi-function terminal input is enabled
Freq. Ref. Selection:
0 - Digital Operator
1 - Speeds from Digital Inputs (n24 - n31)
2 - Analogue Freq. Ref. (0-10volt)
3 - Analogue Freq. Ref. (4-20mA)
5 - Pulse train Input
Maximum Frequency
Maximum Voltage
Maximum Voltage Frequency
Acceleration time 1
Deceleration time 1
Frequency Reference 1
"
Frequency Reference 8
Rated motor current
Multi-function input 1 (S1)
Multi-function input 2 (S2)
Multi-function input 3 (S3)
Multi-function input 4 (S4)
Multi-function input 5 (S5)
Multi-function input 6 (S6)
Multi-function input 7 (S7)
Multi-function output (MA-MB-M )
Multi-function output (P1-P )
Multi-function output (P2-P )
Multi-function analogue output
arrier Frequency
D Injection Braking urrent
D Injection Braking at Stop Time
D Injection Braking at Start Time
Stall pevention during deceleration:
0 = Stall prevention enabled
1 = Braking Resistor Effective
n001
n003
n004
n011
n012
n013
n019
n020
n024
"
n031
n036
n050
n051
n052
n053
n054
n055
n056
n057
n058
n059
n066
n080
n089
n090
n091
n092
0 to 9
0 to 5
0 to 9
50 to 400
0.1 to 255
(0.1 to 510)
0.2 to 400
0 to 6000
0 to 6000
0 to max. freq.
"
0 to max. freq.
0 to 150% of
rated Inverter
output current
1 to 25
1 to 25
1 to 25
1 to 25
1 to 25
1 to 25
1 to 25,34,35
0 to 19
0 to 19
0 to 19
0 to 5
1 to 4
0 to 100%
0 to 25.5s
0 to 25.5s
0 to 1
1
0
0
60
200
(400)
60
10
10
6
0
0
Varies with
Inverter
model
1
2
3
5
6
7
10
0
1
2
0
3
50%
0.5
0
0
3-12
5-2
5-11
5-12
5-7
5-7
5-7
5-25
5-25
5-18
5-18
5-18
5-5
5-7
5-30
5-30
5-30
5-30
5-30
5-30
5-30
5-34
5-34
5-34
5-36
6-26
6-29
6-29
6-29
6-31
Parameter No. escription Range efault Manual Ref. Page
Quick Start Parameter List (Refer to manual for complete list)

Power ON
Press the Mode Key repeatedly until the PRGM
indicator is lit.
Use the Increment or Decrement Key to set the
parameter number.
Press the Enter Key.
The data of the selected parameter number will be
displayed.
Use the Increment or Decrement Key to set the
data. At that time the display will flash.
Press the Enter Key so that the set value will be
entered and the data display will be lit. (see note 1)
The parameter number will be displayed.
In approx. 1s
Key sequence Indicator isplay example Explanation
Multi-function Inputs
Value Function
1 Forward/Stop
2 Reverse/Stop
3 External fault (NO)
4 External fault (N )
5 Fault reset
6 Multi-step speed reference 1
7 Multi-step speed reference 2
8 Multi-step speed reference 3
9 Multi-step speed reference 4
10 Inching command
12 External base block (NO)
13 External base block (N )
17 Local/Remote selection
Multi-function Outputs
Value Function
0 Fault output
1 During RUN
2 Frequency agree
6 Overtorque being monitored (NO)
12 RUN mode
13 Inverter ready
15 Undervoltage in progress
Analogue Output Functions
Value Function
0 Multi-step speed reference 3
1 Multi-step speed reference 4
2 Inching command
3 External base block (NO)
Note: Refer to Section 5-10/11 for full set value listings
Note 1: To cancel the set value, press the Mode Key instead. The parameter number will be displayed.
Note 2: There are parameteres that cannot be changed while the Inverter is in operation. Refer to the list of
parameters. When attempting to change such parameters, the data display will not change by pressing
the Increment or Decrement Key.
ancels
set data
In approximately 1s
Example of Parameter Settings

heck output for short circuit or ground fault.
The Load is too large, reduce it or use larger Inverter.
heck motor FLA rating compared to Inverter and V/F setting.
Load inertia is too large and the motor is regenerating.
Increase deceleration time (n020 or n022).
onnect an external braking resistor and set n092 to 1.
heck braking resistor and wiring.
heck mains power supply voltage and connections.
heck correct supply for Inverter being used.
Monitor for mains dips or interuptions.
Refer to manual for installation guidelines and recommendations.
heck cooling fan (if fitted).
heck V/F characteristic or reduce arrier frequency.
heck and reduce the load.
heck V/F characteristic (Vmax and Fmax).
Increase the running speed of the motor.
Increase acceleration/deceleration times.
heck your control terminal wiring.
A multi-functional digital input has been set to 3 or 4.
Run signal must be removed before this can be reset.
Inverter must be stopped when Local/Remote switching
attempted.
Inverter must be stopped when omms/Remote switching
attempted.
heck your control terminal wiring.
A multi-function digital input has been set to 12 or 13.
Forward and reverse run signal have been applied
simultaneously.
The values in n050 through n056 for multi-function inputs 1
through 7 have been duplicated - check and correct the values.
Overcurrent
Output current is higher than
250% of Inverter rated current.
Overvoltage
D bus voltage has exceeded
detection level.
Main circuit undervoltage
D bus voltage is below
detection level.
Unit overheated
Temperature inside the inverter
has exceeded 110° .
Motor overload
The Inverter is protecting the motor
from overload based on an internal
I≈T calculation using n036 setting.
External fault
An external fault has been input.
Sequence error
Sequence input when Inverter
running.
External baseblock
An external baseblock command
has been input.
Sequence error has occurred
Operation error
Parameter setting error.
OC
OV
uV1
OH
OL1
EF*
SER
(flashing)
bb
(flashing)
EF
(flashing)
oP1
(flashing)
Fault isplay Fault name and meaning Possible cause and remedy
Protective and iagnostic Functions
Note: Refer to Section 8-2 for full fault code listings
Improper procedures can result in personal injury or
equipment damage. Use the Quick Start Guide only if you
are familiar with standard safety precautions common to
variable speed drives. See Operation Manual I527 for
further details.