Omron Techman Robot User guide

Safety Manual TECHMAN ROBOT Safety System 3.3i
Safety Manual
Original Instruction
TECHMAN ROBOT Safety System 3.3
1648-E-04

Safety Manual TECHMAN ROBOT Safety System 3.32
This Manual contains information of the Techman Robot product series (hereinafter referred to as the TM Robot). The
information contained herein is the property of Techman Robot Inc. (hereinafter referred to as the Corporation) and
shall not be reproduced in whole or in part without prior authorization from the Corporation. No information contained
herein shall be considered an offer or commitment. The information herein is subject to change without notice. The
document is periodically reviewed and revised. The Corporation assumes no responsibility for any errors or omissions
in the documentation.
logo is registered trademark of TECHMAN ROBOT INC. in Taiwan and other countries and the company
reserves the ownership of this manual and its copy and its copyrights.

Safety Manual TECHMAN ROBOT Safety System 3.33
Terms and Conditions Agreement
Warranty Limitations of Liability
Warranties
Exclusive Warranty
Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a
period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron).
Omron disclaims all other warranties, express or implied.
Limitations
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF
THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based
on infringement by the Products or otherwise of any intellectual property right.
Buyer Remedy
Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped
with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii)
repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the
non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity
or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or
inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before
shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of
Products in combination with any electrical or electronic components, circuits, system assemblies or any
other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.

Safety Manual TECHMAN ROBOT Safety System 3.34
Limitation of Liability; Etc
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which
liability is asserted.
Application Considerations
Suitability of Use
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply
to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron
will provide applicable third party certification documents identifying ratings and limitations of use which apply to
the Product. This information by itself is not sufficient for a complete determination of the suitability of the
Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely
responsible for determining appropriateness of the particular Product with respect to Buyer’s application,
product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Programmable Products
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any
consequence thereof.
Disclaimers
Performance Data
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user
in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test
conditions and the user must correlate it to actual application requirements. Actual performance is subject to
the Omron’s Warranty and Limitations of Liability.

Safety Manual TECHMAN ROBOT Safety System 3.35
Change in Specifications
Product specifications and accessories may be changed at any time based on improvements and other
reasons. It is our practice to change part numbers when published ratings or features are changed, or when
significant construction changes are made. However, some specifications of the Product may be changed
without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications
for your application. Please consult with your Omron representative at any time to confirm actual specifications
of purchased Product.
Errors and Omissions
Information presented by Omron Companies has been checked and is believed to be accurate; however, no
responsibility is assumed for clerical, typographical or proofreading errors or omissions.

Safety Manual TECHMAN ROBOT Safety System 3.36
Revision History Table.......................................................................................................................................................9
1. Comprehensive Information ........................................................................................................................................10
Overview ............................................................................................................................................................10
Applicable Product Version ................................................................................................................................10
Safety Warning Symbols....................................................................................................................................10
Safety Precautions............................................................................................................................................. 11
Validation and Responsibility .............................................................................................................................12
Limitation of Liability...........................................................................................................................................12
Overall Safety Warning ......................................................................................................................................12
Intended Use......................................................................................................................................................14
Risk Assessment................................................................................................................................................15
2. Safety Function ...........................................................................................................................................................17
2.1 Overview ............................................................................................................................................................17
2.2 General Information ...........................................................................................................................................17
2.2.1 Safety Function Definitions .........................................................................................................................17
2.2.2 Stopping Time and Stopping Distance in the Safety System......................................................................18
2.2.3 Software Safety Setting Permissions..........................................................................................................18
2.3 Explanation of Safety Functions ........................................................................................................................18
2.3.1 SF0 Robot Stick ESTOP and SF1 User Connected ESTOP Input .............................................................18
2.3.2 SF2 Encoder Standstill................................................................................................................................20
2.3.3 SF3 User Connected External Safeguard Input and SF9 User Connected External Safeguard Input for
Human-Machine Safety Settings..........................................................................................................................20
2.3.4 SF4~SF8 Defined Safety Functions............................................................................................................21
2.3.5 SF10~SF14 Safety Output Functions .........................................................................................................24
2.3.6 SF15 and SF16 Safety Input Functions ......................................................................................................27
2.3.7 SF17 Cartesian Limit A ...............................................................................................................................29
2.3.8 SF18 Cartesian Limit B ...............................................................................................................................29
2.3.9 Safety Checksum ........................................................................................................................................30
3. Safety Related Operation............................................................................................................................................31
Joint Movement without Drive Power ................................................................................................................31
During an Emergency Stop Procedure .......................................................................................................31
Extending the Robot from the Packing Pose ..............................................................................................31
Power Loss..................................................................................................................................................31
Operation Mode and Mode Switching................................................................................................................32
Auto Mode ...................................................................................................................................................32
Contents

Safety Manual TECHMAN ROBOT Safety System 3.37
Manual Mode...............................................................................................................................................32
Switch Between Modes...............................................................................................................................33
Hold to Run ........................................................................................................................................................33
Singularity Point .................................................................................................................................................34
Replacing the Robot Stick in Local Control .......................................................................................................39
4. Compliance of Safety Regulations..............................................................................................................................40
Compliance ........................................................................................................................................................40
Requirement of Enabling Device.................................................................................................................40
Access of Safety Setting .............................................................................................................................40
5. Declaration of Incorporation........................................................................................................................................41
Appendix A. Certificate of Compliance and Declaration of Incorporation .......................................................................44
Appendix B. Verifications of EMC Compliance ...............................................................................................................48
Appendix C. TM Robot Stopping Time and Distance for all Series Product Models ......................................................50
Tables
Table 1: Safety System Version........................................................................................................................10
Table 2: Safety Warning Symbols..................................................................................................................... 11
Table 3: Safety Function Definitions .................................................................................................................17
Table 4: Stop Category and Action of Fault Detection of SF0 and SF1 ...........................................................19
Table 5: Stop Category and Action of Fault Detection of SF3 and SF9 ...........................................................21
Table 6: SF4~SF8 Defined Safety Functions ...................................................................................................22
Table 7: Stop Category and Reaction of Fault Detection of SF4~SF8.............................................................22
Table 8: Output Signal and Action of Fault Detection of SF10~SF14...............................................................26
Table 9: Application example of Safety Output Function..................................................................................27
Table 10: Stop Category and Reaction of Fault Detection of SF15 and SF16.................................................28
Table 11: Stop Category and Reaction of Fault Detection of SF17..................................................................29
Table 12: Stop Category and Reaction of Fault Detection of SF18..................................................................30
Table 13: The Roffset values of each product series...........................................................................................34
Table 14: Control Methods in Respective Modes Summary.............................................................................39
Table 15: Declaration of Incorporation..............................................................................................................43
Table 16: Stopping Time and Distance for TM5-700 Series .............................................................................50
Table 17: Stopping Time and Distance for TM5-900 Series .............................................................................51
Table 18: Stopping Time and Distance for TM14 Series ..................................................................................52
Table 19: Stopping Time and Distance for TM12 Series ..................................................................................53
Figures
Figure 1: X, Y, & Z axes ....................................................................................................................................24

Safety Manual TECHMAN ROBOT Safety System 3.38
Figure 2: Checksum..........................................................................................................................................30
Figure 3: The Definition of Roffset. ......................................................................................................................35
Figure 4: Extensible Singularity Point in Space................................................................................................36
Figure 5: Wrist Singularity Point in Space ........................................................................................................36
Figure 6: The Solution when Encountering Singularity Point in Space (1/2)....................................................37
Figure 7: The Solution when Encountering Singularity Point in Space (2/2)....................................................38

Safety Manual TECHMAN ROBOT Safety System 3.39
Revision History Table
Revision Date Revised Content
01 December 2019 Original release
02 January 2020 Updated Appendix A
03 April 2020 Updated Chapter 4.1.2
04 August 2020 Updated info on Safety System 3.3 and Appendix A

Safety Manual TECHMAN ROBOT Safety System 3.310
1. Comprehensive Information
Overview
This chapter describes the comprehensive important safety information of TM Robot. The user and system
integrator of TM Robot must read and fully understand this chapter before using this robot.
Applicable Product Version
This document is only applicable to the combination of the following software and hardware versions of TM Robot.
Users can check the hardware version and software version on “Techman Robot Product Brief Information” sheet
in the control box carton, or through these methods: checking the hardware version on the product label on the
control box and checking the software version from the software information button in the UI of TMflow. If the
software version of the robot has been upgraded and is different from the original out-of-the-box one, users should
only check the software version from the UI of TMflow.
Safety System version: TECHMAN ROBOT Safety System 3.3*
Hardware version HW 3.2
Software version SW 1.80
*Within the scope of hardware and software combination above, the safety system
version remains the same as TECHMAN ROBOT Safety System 3.3
Table 1: Safety System Version
Users shall confirm whether the software and hardware version of the TM Robot is consistent with the applicable
product version of this Safety Manual. The Corporation is not responsible for any safety issues caused by referring
to the safety instruction of an incorrect version.
Safety Warning Symbols
The following table defines the levels of the safety warning symbols that are marked in each paragraph in this
Manual. Read carefully and comply with each paragraph to avoid harm to people or equipment.
DANGER:
Identifies an imminently hazardous situation which, if not avoided, is likely to result in serious
injury, and might result in death or severe property damage.
WARNING:
Identifies a potentially hazardous situation which, if not avoided, will result in minor or moderate
injury, and might result in serious injury, death, or significant property damage.
CAUTION:
Identifies a potentially hazardous situation which, if not avoided, might result in minor injury,
moderate injury, or property damage.

Safety Manual TECHMAN ROBOT Safety System 3.311
WARNING: ELECTROCUTION RISK
Identifies a hazardous electrical situation.
Table 2: Safety Warning Symbols
Safety Precautions
DANGER:
This product can cause serious injury or death, or damage to itself and other equipment, if the
following safety precautions are not observed.
All personnel who install, operate, teach, program, or maintain the system must read the Hardware
Installation Manual, Software Manual, and Safety Manual according to the software and hardware version of
this product, and complete a training course for their responsibilities concerning the robot.
All personnel who design the robot system must read the Hardware Installation Manual, Software Manual,
and Safety Manual according to the software and hardware version of this product, and must comply with all
local and national safety regulations of the location where the robot is installed.
Observe the “Intended Use” section in Safety Manual.
If the installation and application does not observe human-robot collaboration regulations of the safety
regulations, the user is responsible for providing safety barriers around the robot to prevent anyone from
accidentally coming into contact with the robot when it is in motion.
If any local or national electrical regulation requires, power to the robot and its power supply must be locked
out and tagged out, or have means to control hazardous energy or implement energy isolation before any
maintenance is performed.
Dispose of the product in accordance with the relevant rules and regulations of the country or area where
the product is used.
Read Manual and Impact Warning labels

Safety Manual TECHMAN ROBOT Safety System 3.312
Validation and Responsibility
The information provided in this Manual does not include how to design, install and operate a complete arm
application, nor does it include the peripheral devices that will affect the overall system safety. The design and
installation of the complete system must comply with the standards and regulations for safety requirements in the
country located. The robot integrator needs to understand safety laws and safety regulations in the local countries,
in order to avoid major risks existing in the entire system.
This includes but is not limited to:
Performing a risk assessment of the whole system
Adding other machines and additional risk reduction measures based on the results of the risk assessment
Using appropriate software safety features
Ensuring the user will not modify any safety measures
Ensuring all systems are correctly designed and installed
Specifying instructions for use
Clearly marking the contact information of the integrator that installed the robot
Making relevant documents accessible, including the risk assessment, and this manual
CAUTION:
This product is partly completed machinery. The design and installation of the complete
system must comply with the safety standards and regulations in the country of use. The user
and integrators of the robot should understand the safety laws and regulations in their
countries and prevent major hazards from occurring in the complete system.
Limitation of Liability
Even if the safety instructions are followed, any safety-related information in the manual shall not be considered as
a guarantee that the product will not cause any personal injury or damage.
Overall Safety Warning
These safety warnings are relevant for the entire manual.

Safety Manual TECHMAN ROBOT Safety System 3.313
DANGER:
1. Before transporting, installing, operating, maintaining and repairing this product, make sure to read the product
specification and operation manual in detail. Confirm that all the conditions comply with the requirements of the
specification and the Manual, to avoid unintended accidents (for example: improper operation or conditions of
use that exceed the product specification) that may result in injury to personnel.
2. Before installing and using this product, the integrator must perform a risk assessment and implement risk
reduction measures.
3. Users shall create procedures for emergency and abnormal situations.
4. Before using this product, make sure that the emergency stop device functions correctly.
WARNING:
1. Before disassembling or repairing this product, make sure that the power has been turned off and disconnected
before proceeding to avoid injury to people or damage to machinery caused by inadvertent short circuit or
electric shock.
2. When operating this product, the operator shall avoid wearing loose clothing or wearing other accessories (such
as: necklaces, ties, bracelets, etc.) to avoid injury caused by clothing or accessories becoming entangled in the
machine during operation.
3. If the product malfunctions, follow the established procedures of your organization to obtain repair of the product.
Do not attempt to repair the product yourself to avoid damage to the machinery.
4. Before the robot is in operation, make sure that each part has been completely mounted to avoid any possibility
of accidents.
5. Before starting the operation of the robot, confirm that there are no persons or obstacles that may intrude into
the operating area during operation. If the operating environment uses human-robot cooperative operation, be
sure to complete the due risk assessment before starting the operation.
6. It is forbidden for any unauthorized person to operate this product in order to avoid any possibility of injury to
personnel or damage to the machinery.
7. Do not install or operate this product in a hazardous area (for example: strong magnetic field, hazardous gas,
fire source, or flammable product) In order to prevent the machinery from causing danger during operation
because of external conditions.

Safety Manual TECHMAN ROBOT Safety System 3.314
CAUTION:
1. Before operating the robot, confirm the status of the machinery warning light.
2. After editing the task flow, operate the robot in the Manual Mode first, and confirm that all the movements in the
task flow are correct before switching the operation mode to Auto Mode.
3. During the operation of machinery, do not turn off the power supply to prevent possible damage to the system.
4. For the robot noise levels and related environmental conditions, refer to the Hardware Installation Manual for the
corresponding hardware version.
Intended Use
The TM Robot is designed so the hazards can be reduced to tolerable levels when installed as specified and
operated under normal and intended use.TM Robots have been designed and constructed in accordance with
relevant safety standards. TM Robots are intended for use in parts assembly and material handling for payloads
(including end-effector and workpiece) up to the “Maximum Payload” specification of each model.
The TM Robot focuses on the safety of human-robot cooperative operation by design, but the cooperative
operation is only for application procedures that have undergone a risk assessment including robots, related
peripheral equipment and working environment.
Any use or application should consider the risk assessment. If the use is different from the intended application,
The Corporation will not bear any responsibility. The Corporation clearly specifies that the following uses are not
suitable for the TM Robot. This is not a complete list.
•Use in a potentially hazardous environment
•Use in any applications that may threaten human lives
•Use in any application that may cause personal injuries
•Use before completion of the risk assessment and implementation of risk reduction measures
•Use for life support
•Use when the rated performance cannot be reached
•Use when the reaction time of safety functions is insufficient
•Use without appropriate parameters in operations
•Use in applications which may cause damage to the robot itself
•Restricted movement of persons
•Use without proper mounting of the robot
•Use involving excessive oscillations when moving
•Use without proper design of earthquake-prevention mounting when installed in earthquake zones

Safety Manual TECHMAN ROBOT Safety System 3.315
•Use without safe access to (or at/from) the work station
•Use in the presence of exhaust gases/lack of oxygen at the work position
•Use in the presence of flame (flammability of the cabinet, lack of extinguishing means)
•Use with mechanical hazards at the work position: a) rollover; b) fall of objects, penetration by objects; c)
break-up of parts moving at high speed; d) contact of persons with machine parts or tools (non-collaborative
machines)
•Use with insufficient visibility from the work positions
•Use with inadequate lighting
•Use with inadequate seating
•Use with insufficient means for escape or entrapment avoidance
•Use with inadequate location of manual controls
•Use with inadequate design of manual controls and their mode of operation
Risk Assessment
Before installing and using this product, the user must first perform a risk assessments based on the conditions of
use. Risk assessments can be in reference to the specifications of ISO 10218-2, ISO 12100 and ISO/TS 15066
documentations. The purpose of a risk assessment is to anticipate any accidents that may occur during the
operation process and by means of appropriate protective measures to reduce the occurrence of accidents or to
reduce the severity of injury to persons in the event of an accident. Therefore, the risk assessment needs to include
any operational actions of the machinery within the scope of the assessment. After the risk assessment is
completed, the user can use external related components (i.e. sensing components, emergency stop devices,
fences or railings, etc.) as well as the parameter settings of safety functions in the operating system, to reduce
possible occurrence of accidents. Additional safety-related components must be installed in accordance with the
manufacturer's specifications for the required risk reduction. For operating system safety settings and other safety
components usage, read and understand this manual, the Software Manual and the Hardware Installation Manual
of corresponding versions.
Potential hazards requiring additional risk reduction measures may include but are not limited to:
1. Finger(s) (especially in the case of hand guiding) caught between the rear end of the camera module and the
joint module(s).
2. The palm or finger injured by the motion of the robot or the hand guide teaching, if caught between the robot
end-effector (including the workpiece) and the robot body.
3. Being hit by a robot and injured.
4. Entrapment between a robot and a fixed surface.
5. Incorrect human-robot collaborative workspace setup, parameter settings or project operation.
6. TCP force may be estimated incorrectly when robot is passing the area near singularity point in space, due to

Safety Manual TECHMAN ROBOT Safety System 3.316
the nature of singularity.
WARNING:
Ensure compliance with all local and national safety and electrical codes for the installation and
operation of the robot system.
WARNING:
Provide appropriately sized Branch Circuit Protection and Lockout/Tagout Capability in
accordance with the National Electrical Code and any local codes.
WARNING: ELECTROCUTION RISK
It is necessary for a skilled and instructed person to perform AC power installation. During
installation, it is mandatory to prevent unauthorized third parties from turning on power with the
use of lockout/tagout measures.
Failure to use appropriate power can lead to malfunction or failures of the robot or hazardous
situations.

Safety Manual TECHMAN ROBOT Safety System 3.317
2. Safety Function
2.1 Overview
TM Robot incorporates multiple safety functions, and provides interfaces for additional external protective devices.
2.2 General Information
The following describes common information of the TM Robot system safety functions:
2.2.1 Safety Function Definitions
Safety Function Definitions of TM Robot System are listed in the following table:
Safety
Function
Number
Name Robot Stopping
Function
Structure
Category PL
SF0
Robot Stick ESTOP
Emergency Stop
Cat. 3
d
SF1
User Connected ESTOP Input
Emergency Stop
Cat. 3
d
SF2 Encoder Standstill Protective Stop Cat. 2 d
SF3 User Connected External Safeguard Input Protective Stop Cat. 2 d
SF4 Joint Torque Monitoring Protective Stop Cat. 2 d
SF5 Joint Position Limit Protective Stop Cat. 2 d
SF6 Joint Speed Limit Protective Stop Cat. 2 d
SF7 TCP Speed Limit Protective Stop Cat. 2 d
SF8 TCP Force Limit Protective Stop Cat. 2 d
SF9 User Connected External Safeguard Input for
Human-Machine Safety Settings
-- Cat. 2 d
SF10 Robot ESTOP Output -- Cat. 3 d
SF11 User Connected External Safeguard Output -- Cat. 3 d
SF12 User Connected External Safeguard Output for
Human-Machine Safety Settings
-- Cat. 3 d
SF13 Robot Internal Protective Stop Output -- Cat. 3 d
SF14 Robot Moving Output -- Cat. 2 d
SF15 User Connected Enabling Device Input Protective Stop Cat. 2 d
SF16 User Connected ESTOP Input without Robot
ESTOP Output
Emergency Stop Cat. 3 d
SF17 Cartesian Limit A Protective Stop Cat. 2 d
SF18 Cartesian Limit B -- Cat. 2 d
Table 3: Safety Function Definitions
Note:
1. The structure category according to ISO 13849-1:2015.
2. PL (Performance Level) in accordance with ISO 13849-1:2015.
3. Emergency stop and protective stop in accordance with ISO 10218-1:2011.
4. Stop categories in accordance with IEC 60204-1.

Safety Manual TECHMAN ROBOT Safety System 3.318
2.2.2 Stopping Time and Stopping Distance in the Safety System
Safe stopping time is the time required from when an emergency stop or protective device (i.e. internal or
external) is activated and motion stops. In this system, activating the emergency stop button will apply Cat.
1 safety stop. Activation of a safety function or external safety protective device will be a Cat. 2 stop. It may
be necessary for the user or the system integrator to take these stop times into consideration when
implementing risk reduction measures. The robot continues moving during this time, which can transmit
energy and present additional risk. Refer to Appendix C for stopping time and stopping distance.
2.2.3 Software Safety Setting Permissions
A change management process should be in place listing known acceptable settings and potential hazards.
Changes are made in the permissions management function. The authorized user must log in with
administrator’s privilege to set all levels of permissions appropriately. Cybersecurity measure should take
place when using a network connection. The Corporation is not liable for the possible harm caused by
malicious attacks or intrusion of the users’ network to modify the permissions management system or
safety setup.
2.3 Explanation of Safety Functions
2.3.1 SF0 Robot Stick ESTOP and SF1 User Connected ESTOP Input
The SF0 Robot Stick ESTOP refers to the built-in Emergency Switch on the Robot Stick of the TM Robot
control box, and the SF1 User Connected ESTOP Input refers to the Emergency Stop Port on the control
box, which is applicable to connect additional emergency switches.
Refer to the table below for the stop category and the reaction of the fault detection of the safety functions.
The functions come with discrepancy detection to maintain safety when detecting conflicting signals from
the dual channel input. When a discrepancy occurs, the system will enter and lock in a safety status. To
resume from the safety status, first check the input wiring, correct it, and let the dual inputs open and close
again, to enable the robot to the resume status of the safety function. When any fault other than
discrepancy in the safety functions is detected, the system performs a Cat. 0 stop. When Cat. 0 stop occurs,
reboot the robot system to recover from Cat.0 stop status.

Safety Manual TECHMAN ROBOT Safety System 3.319
Safety
Function
Number
Name Stop
Category
Action of
Fault Detection
SF0 Robot Stick ESTOP Cat. 1 stop Discrepancy: Cat.1 Stop
Others: Cat. 0 stop
SF1 User Connected
ESTOP Input
Cat. 1 stop Discrepancy: Cat.1 Stop
Others: Cat. 0 stop
Note: Stop categories in accordance with IEC 60204-1.
Table 4: Stop Category and Action of Fault Detection of SF0 and SF1
The user can stop movement by pressing the Emergency Stop button. After the movement of the robot has
ceased, the user must confirm that no hazardous conditions are present before manually releasing the
Emergency Stop button to allow reactivation of the robot. The Emergency Stop should be used only when a
critical condition occurs. To stop the movement of the robot under normal operation, use the Stop Button on
the Robot Stick.
If the risk assessment requires additional Emergency Stop devices, the selected device must comply with
the requirements of the IEC 60204-1. Any additional Emergency Stop Devices must be connected to the
User Connected ESTOP Input port (SF1), so they do not diminish the overall performance level of the
Emergency Stop.
Activation of an emergency stop initiates a Cat. 1 stop. The Indication Light Ring of the robot will not display
light and the three lights on the Robot Stick will be constantly blinking. The steps to reset the emergency
stop are as follows:
1. Rotate the Emergency Switch to the pop-up state. At this time, the robot arm will be re-powered. The
Indication Light Ring will have the light blue light on to indicate the Safe Start up Mode.
2. Press the Stop Button on the Robot Stick for about three seconds. The robot will perform the calibration
action of the start-up process and return to the previous operating mode.
WARNING:
The power of the robot arm will be cut and the joint brake will be activated, if the Emergency
Stop is triggered. The Indication Light Ring of robot’s end module will not show light and the
three lights from the robot stick will be constantly blinking. In this case, although each of the
joints will be automatically locked by their brakes, the robot body will still drop slightly, before it
completely stops. Pay attention to the risk that the end part of the robot may pinch the
operator or collide with other objects.

Safety Manual TECHMAN ROBOT Safety System 3.320
WARNING:
During an Emergency Stop, power to the end effector will be cut. If the system was integrated
with a power I/O enabled end effector, the emergency stop condition may cause the
workpiece to be dropped.
CAUTION:
Personnel should be outside of the robot’s operational space (areas that robot can reach)
when recovering from the emergency stop.
Clear off the loading at the tool end before recovering from the emergency stop.
CAUTION:
During the Joint Position Calibration period, each joint of the robot will perform a calibration
motion. Make sure the robot pose is in a clear space of at least 5 degrees per joint to perform
the calibration motion before starting the calibration. At the same time, make sure the TCP,
which may have a long distance to the robot flange, will not causing harm during the
calibration motion.
2.3.2 SF2 Encoder Standstill
This safety function is automatically activated after every Cat. 2 Stop. Encoders of each joint are monitored
continuously to check if there is any unintended motion until the user acknowledges and manually resets
the robot from the state of Cat. 2 Stop. If there is any unintended motion, this safety function will trigger a
Cat. 0 Stop. When any fault other than discrepancy is detected in the safety function, the system performs
a Cat. 0 stop. When a Cat. 0 stop occurs, reboot the robot system to recover from Cat. 0 stop status.
2.3.3 SF3 User Connected External Safeguard Input and SF9 User Connected External Safeguard Input for
Human-Machine Safety Settings
These two safety inputs are present on the Safeguard Port of the robot control box. For the related
connection and usage, refer to the Hardware Installation Manual. Resuming from the SF3 User Connected
External Safeguard Input protective stop and SF9 User Connected External Safeguard Input for
Human-Machine Safety Settings can be manual or auto. If manual resume is configured, press the PLAY
button to resume the original status. For the setting for manual or automatic resume, refer to the relevant
contents in the Software Manual.
Refer to the table below for the stop category and the reaction of fault detection of the safety functions. The
functions come with discrepancy detection to maintain the safety status when detecting conflicting signals
from a dual channel input. When a discrepancy occurs, the system will enter and lock in a safety status of
Cat. 1 stop. To resume from the safety status, first check the input wiring, correct it, and follow the steps
below to resume.
1. Let the dual inputs open and close again. At this time, the robot arm will be re-powered. The Indication