Openplan XPAND UP User manual

Tools Required
For additional assembly support, refer to www.openplan.com
or contact 844.OPS.OPS1
Cordless Drill
Philips bit with extension
for Work Surface screws
(XP-Screw-WS)
Measuring Tape
3/16 Hex drive bit
for XP-Screws
Level
XPAND UP
Height Adjustable Dual Station– Assembly
Instructions
www.openplan.com | 844.OPS.OPS1 | [e-mail]
Rubber Mallet

XPand Parts Used for Assembly
Item Part name Part
Description
Image
1 XP-HA-Base, leg Legs for XP-HA-
Base
2 XP-SB-Bracket Stretcher Bar
Bracket
3 XP-HA-LR-30 HA- Leg Rail, 30”
4 XP-HA-Base,
Frame support
Frame support
for HA-Base
5 XP-HA-LRC-30” Leg Rail Cover
30”
6 XP-HA-SB-XX Stretcher Bar, XX”
7 XP-CTA-XX Cable Tray
2
Item Part name Part
Description
Image
8 XP-CTC Cable Tray Clip
9 XP-CTCXX Cable Tray
Cover, XX”
10 HA-Base-Screw M6X14 Hex
screw
11 XP-Screw-WS 10-9X1 PH Pan
Head, ST P’bd
12 XP-Screw 5/16-18 x .5” Hex
Socket Cap
13 XP-HA--TXXXX HA Work Surface
XPand UP – Height Adjustable Dual Station

Step 1: Prepare a large floor space to put the XPand order together. Unpack the parts and check to see if all the XPand parts are present
as per the sales order pick list.
Step 2: Assemble the HA-Leg Rail (XP-
HA-LR-30) to the Height Adjustable
Leg using (2) XP-Screws.
3
Step 3: Assemble the other end of the
Leg Rail to another Height adjustable
leg using (2) XP-Screws.
Left leg
Right leg
Step 4: Assemble (2) Stretcher Bar Bracket (XP-SB-
Brackets) to the HA-Leg Rail using (2) XP-Screws per
Bracket. Make sure the Top Face of the Bracket
faces upwards. Figure A shows the Top Face of
the Bracket.
Bracket on top/rear
indicates “Top”.
Figure A
(XP-SB-Bracket)
XPand UP – Height Adjustable Dual Station

Step 5: Assemble the Stretcher Bar (XP-SB-XX) to the
Stretcher Bar Bracket (XP-SB-Bracket) using (3) XP-Screws
per Stretcher Bar.
Step 6: Repeat Step 1 to Step 6 to assemble the other end of
Height Adjustable Leg Assembly.
4
XPand UP – Height Adjustable Dual Station
Step 7: Slide (4) Cable Tray Clips onto each
cable tray.

www.openplan.com | 844.OPS.OPS1 | [e-mail]
5
Step 8: Snap on the assembled cable tray clips to the
Stretcher bar.
XPand UP – Height Adjustable Dual Station
Step 9: Using the HA-Base screws provided with the
HA-Base, assemble the Height Adjustable Frame to
the Legs.

www.openplan.com | 844.OPS.OPS1 | [e-mail]
6
Step 11: Assemble Cable Tray Cover (XP-CTC) to the Height Adjustable
Frame using (4) XP-Screws.
Step 12: Place the Work Surface (XP-HA-TXXXX) on the frame.
Center the Work Surface to the frame and secure the Work
Surface to the Frame using (6) XP-Screw-WS per each Work
Surface.
Note: If the Fabric Screen dividers are used on the Height Adjustable Stations, slide-in the
Screen Brackets (XP-SB-HA) into the covers before the Cable Tray Covers are assembled.
For thin Screens XP-SB-HA-T is used instead of XP-SB-HA.
(XP-SB-HA)
Figure CFigure B
(XP-SB-HA-T)
XPand UP – Height Adjustable Dual Station

Step 14: Level the HA-legs by turning the leveling feet.
www.openplan.com | 844.OPS.OPS1 | [e-mail]
7
Step 13: Snap on the Leg Rail Covers (XP-LRC-XX) to the Leg
Rails.
XPand UP – Height Adjustable Dual Station