opticis DPFX-300-TR User manual

Manual Contents
__________________________________________
Manual Contents
1-0
Welcome! Product Description
1-1
System Requirements for Setup
1-2
Installation
1-3
Troubleshooting, Maintenance, Technical Support, and Service
1-5
Product Specifications
1-6
Warranty Information
1-7
Certifications
1-8
Pictorials
Figure 1 –Overall Connection of DPFX-300-TR
1-1
Figure 2 –Position of the LED
1-3
Figure 3 –Connection of optical fiber
1-4
1-0 Manual Contents
User’s Manual for the
DPFX-300-TR
Doc No. : OE-DP190902 / V1.0
One (1) Fiber DisplayPort 1.2
Optical Detachable Extender

Welcome!
Congratulations on your purchase of the one (1) fiber DisplayPort extender,
DPFX-300-TR. This manual contains information that will assist you in
installing and operating the product.
Product Description
DisplayPort 1.2 one(1) fiber optical detachable extender, DPFX-300, extends
DisplayPort 1.2 signal up to 200m (656feet) and transmits 4K UHD
(4096x2160) at 60Hz over one(1) LC multi-mode fiber. Leading-edge
technology of Opticis allows long distance transmission of 4K signal without
any video/audio degradation.
DPFX-300-TR is designed compact enough to be fitted into various installation
environments. It gives slim, light, easy installation with perfect electrical
isolation, but without electrical hazard and interference.
Between Transmitter (DPFX-300-Tx) and receiver (DPFX-300-Rx), pure fiber
connection by single LC fiber connector gives clean, secure and easy
installation.
DPFX-300-TR can be operated by USB power without external DC power
adapter with plugging micro USB(DPFX-300 module side) –USB
(source/display devices side) cable which is supplied in shipping group.
Figure 1 –Overall Connection of DPFX-300-TR
1-1 Welcome, Product Description
System Requirements for Setup
□Hardware requirements
▪You have to have a DisplayPort source and display. It should
support the maximum graphic resolution feature of displays to
be connected.
▪No special requirements of memory size, CPU speed and
chipsets, if you’ve already properly installed your DisplayPort
systems or graphic cards.
▪Proper initial trial of the entire platform with its application using
a short length copper cable is recommended prior to installation
with the optical link.
□Software requirements
▪No special restrictions, if you’ve already properly installed your
DisplayPort systems.
□Power Technical Advisory
▪Enclosed Power Adaptors and USB cables supply power to both
Transmitter and Receiver.
□Connection Advisory
▪It is highly recommend that DisplayPort source is directly
connected into DisplayPort display output via DPFX-300-TR
without connection to incompatible distributor, switcher
and selector.
The Shipping Group of DPFX-300-TR;
One (1) Transmitter (Tx) and One (1) Receiver (Rx)
One (1) 0.2m Male to Female DisplayPort copper cable
Two (2) Micro USB to USB cables
Two (2) 5V 1A power adapter
User’s Manual
※Default connection is direct connection to both source (Tx side) and
display (RX side)
※If direct connection is impracticable, 0.2m DisplayPort copper cable
is strongly recommended to use on Tx(Display Source) side only
1-2 System Requirements for Setup

Installation
Important: Please keep the installation procedure below. Improper or no
operation may result if the start-up sequence is not correctly followed.
Step 1
Carefully unpack the contents in the shipping group.
Step 2
Power on the DisplayPort source and display. Both the transmitter and
receiver will be turned on by 3.3V from pin #20 of DisplayPort interface. The
USB power is recommend for the stable power supply for both the transmitter
and receiver.
Step 3
The Power LED will be turned on when DPFX-300-TR is connected to
DisplayPort interface of signal source and display and the Status LED will
blink three (3) times. Then the Status LED will blink again when the whole
connection is made.
Figure 2 –Position of the LED
Step 4
Connect one (1) LC optical fiber between the transmitter and the receiver.
Ensure the connectors are fully engaged and then, the top LED will begin to
blink regularly.
Note1: Please DO NOT look directly into the LC receptacles of the
Transmitter, while it is powered on, although this product is regulated strictly
enough to operate under the LASER Class I, classified by CDRH/FDA for eye
safety.
Note2: The maximum extension length by OM3 fiber is 200 meters (656ft.).
Note3: Be recommended NOT to use any intermediate cable or adapter
between them to avoid undesirable performance degradation.
1-3 Installation
Fig Figure 3 –Connection of optical fiber
Step 5
Connect the transmitter (DPFX-300-Tx) to the DisplayPort source.
Step 6
Connect the receiver (DPFX-300-Rx) to the DisplayPort display.
Note: If the connectors are fully engaged, the bottom LED will turn on.
Step 7
If the system does not work properly, go to the page 1-5 for trouble shooting.
1-4 Installation
Position of the LED

Troubleshooting
The display shows only black screen.
- Ensure that all plugs and jacks used by USB power supplies are firmly
connected. Ensure that the LED is ON.
- Ensure that the DisplayPort is firmly plugged in to the DisplayPort source and
display.
- Ensure that the transmitter and receiver modules plugged correctly to the source
and display, respectively.
- Check if the DisplayPort source and display are powered on and properly booted.
- Reset the system by de-plugging and re-plugging the transmitter DisplayPort or
receiver DisplayPort, or by de-plugging and re-plugging the USB power cables that
are plugged of the transmitter and receiver module
- Re-boot up the system while connecting the module.
Screen is distorted or displays noises.
- Check if the graphic resolution is properly set. Go to the display properties and
tap the settings. Ensure that the resolution sets less than WQUXGA (3840x2400)
at 60Hz refresh ratio.
- Reset the system
- Power down, disconnect and reconnect the optical system cable or USB power
adaptors, and power up
Maintenance
No special maintenance is required for the optical system cables and power
supplies. Ensure that the cables and power modules are stored or used in a
benign environment free from liquid or dirt contamination.
There are no user serviceable parts. Refer all service and repair issues to Opticis
or its authorized distributor.
Technical Support and Service
For commercial or general product support, contact your reseller. For technical
service, contact Opticis by email [e-mail] or visit its website at
www.opticis.com
1-5 Trouble Shooting, Maintenance, Technical Support and Service
Product Specifications
Compliance with DisplayPort standard: supports DisplayPort 1.2a
Extension limit: 200m (656feet) for 4K (4096x2160) at 60 Hz
refresh rate over one (1) LC OM3 fiber (50/125um).
Graphic Transmission Bandwidth: Supports total data rate
21.6Gbps (5.4Gbps per lane).
Supports Dual-mode DP (DP++)
Supports auxiliary /l²C channel over fiber
Support Multi-Stream Transport
Mechanical specifications of transmitter and receiver
Dimensions(WDH):22mm x 67mm x 14mm
Environmental Specifications
Operating temperature: 0°C to 50°C
Storage temperature: -30°C to 70°C
Humidity: 10% to 85%
AC/DC Power Adapter
Power Input: AC 100-240V, 50/60Hz.
Power Output: +5 V, 1A SMPS DC-power Adapter
.
1-6 Product Specifications

Warranty Information
1 (One) Year Warranty
Opticis warrants this optical DP module to be free from defects in workmanshi
p and materials, under normal use and service, for a period of one (1) year fro
m the date of purchase from Opticis or its authorized resellers.
If a product does not work as warranted during the applicable warranty period,
Opticis shall, at its option and expense, repair the defective product or part, d
eliver to customer an equivalent product or part to replace the defective item,
or refund to customer the purchase price paid for the defective product.
All products that are replaced will become the property of Opticis.
Replacement products may be new or reconditioned.
Any replaced or repaired product or part has a ninety (90) day warranty or the
reminder of the initial warranty period, whichever is longer.
Opticis shall not be responsible for any software, firmware, information, or me
mory data of customer contained in, stored on, or integrated with any product
s returned to Opticis for repair under warranty or not.
Warranty Limitation and Exclusion
Opticis shall have no further obligation under the foregoing limited warranty if
the product has been damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized modifications, tampering,
alterations, or service other than by Opticis or its authorized agents, causes
other than from ordinary use or failure to properly use the product in the
application for which said product is intended.
Dispose of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate systems)
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
1-7 Warranty Information
Certifications
CE / FCC, Class 1 Laser Eye Safety
Certification of Eye Safety
This laser product is inside implemented by using 850, 925, 930, 990nm LD
Transceivers, manufactured by Opticis Co., Ltd., which are all certified by
CDRH/FDA referred as classified in Laser Class 1 (IEC60825-1).
Caution –Use of controls or adjustments or performances of procedures
other than those specified herein may result in hazardous radiation exposure.
1-8 Certifications

© 2019 Opticis Co., Ltd. All Rights Reserved
Version 1.0 September 2019
Opticis Locations
OPTICIS HQ
Opticis Co., Ltd.
7F SPG Dream Building
166, Jeongjail-ro,
Bundang-gu,
Seongnam-si, Gyeonggi-do, 13558
South Korea
Tel: [phone]
Fax: [phone]
www.opticis.com
For order support, please contact your Distributor or Reseller.
For technical support, check with the Opticis web site www.opticis.com or
contact [e-mail]