opticis IPKVM-500-ED User manual

-1 -
4K HDMI IPKVM Extender
25-0595/95 - IPKVM-500-ED
User’s Manual
Doc No. : OIPKVM-D161129 / Rev1.2
WWW.OPTICIS.COM

-2 -
Index
1. Product Description.......................................................................................................................- 3 -
2. Main Features ...............................................................................................................................- 4 -
3. Supporting Video Resolutions for Input / Output ..........................................................................- 4 -
4. Shipping Group .............................................................................................................................- 4 -
5. Systems Requirements for Setup .................................................................................................- 5 -
6. Connector descriptions .................................................................................................................- 6 -
7. Setting Local / Remote Authority ..................................................................................................- 8 -
8. LED Indication...............................................................................................................................- 8 -
9. SW & Factory Reset .....................................................................................................................- 9 -
10. Connection ................................................................................................................................- 9 -
11. Remote Manager (PC Program) ............................................................................................ - 10 -
1) Download the PC program....................................................................................………. - 10 -
2) PC Program Installation .................................................................................................... - 10 -
3) Access to menu of PC Program........................................................................................ - 10 -
4) Device (Host /Client) setting: ............................................................................................ - 11 -
5) Advanced Setting: configuration of Bit rate, OSD display and Blocking........................... - 12 -
6) EDID read/write................................................................................................................. - 13 -
7) Update Firmware............................................................................................................... - 15 -
12. IPKVM-500ED Connection & Operation ................................................................................ - 17 -
1) GUI.................................................................................................................................... - 17 -
2) Connection & Operation.................................................................................................... - 17 -
3) Operation with Audio Port ................................................................................................. - 18 -
4) Multicast streaming and Blocking function........................................................................ - 19 -
5) OSD display ...................................................................................................................... - 19 -
13. Product Specifications............................................................................................................ - 20 -
14. External Local/Remote Authority Setting (Option) ................................................................. - 21 -
15. Power Rack (PR5V-16) General Specification ..................................................................... - 23 -
16. Trouble shooting..................................................................................................................... - 25 -
17. Warranty Information.................................................................................................................- 3 -

-3 -
1. Product Description
The OPTICIS 4K HDMI IPKVM Extender, IPKVM-500-ED is designed to distribute, control and
access video with data (USB, RS-232, DIO and audio) anywhere over the standard IP Network.
The transmitter, IPKVM-500-E (Encoder) connected to a HDMI source, encodes the video with data
and transmits it over Ethernet. The receiver, IPKVM-500-D (Decoder) connected to a display,
receives the encoded signal over network and decodes it to regenerates the video and data for users.
The provided PC program makes the transmitters and receivers units in the network can be
automatically or manually detected and configured to individual IP address and helps the any of
receivers can be connected simultaneously to any transmitter within the network to create a virtual
crosspoint matrix system of KVM as well as audio and video only system widely used in Pro-AV
installation.
[Connection diagram]

-4 -
2. Main Features
Extends HDMI/DVI, USB, RS-232, Audio, DIO over network
Supports resolution up to 4K (3840x2160 at 30Hz) or full HD 1080p at 60Hz
Any of transmitters in the network can be accessed by any receiver via provided PC program
Supports Multi-cast 1 x N (up to 200 receivers)
HDMI Loop out port on transmitter for local display
Offers EDID read and write function
Local, remote and console control switch on transmitter
Fast switching time and Low video latency
1 x USB ports for local Keyboard / Mouse (transmitter) and 2 x USB ports for remote
Keyboard / Mouse (Receiver)
Easy to use OSD GUI program and PC program
1U rack (OPSCR-1U) mountable (a quarter width of 19”)
Mounting bracket (OPSCB) complying with VESA 75, 100
♦Application
KVM / RCS / ROS / Video control room
3. Supporting Video Resolutions for Input / Output
1) HDMI 1.4 3840x2160p/24/25/30Hz
2) HDMI 1.4/HDTV up to 1920x1280p60Hz
3) VESA Digital up to 1920x1200p60Hz
Note: Some PC resolutions may not work properly.
4. Shipping Group
IPKVM-500-E: TX (Encoder) or IPKVM-500-D: RX (Decoder)
AC / DC power adaptor: One (1) unit of 5V / 2A
One (1) HDMI male to male cable (1.2m)
One (1) Mini-USB Cable for PC
User’s manual
As an option,
RS-232 cable: DB-9 male to 3Pin terminal block
Switch (TX): Console Switch & RJ11 male to 3Pin terminal block
Indicator (RX): Console Indicator & RJ11 male to 3Pin terminal block
Mounting bracket (OPSCB) complying with VESA 75, 100.
1U Rack (OPSCR-1U)
Power Rack (PR5V-16): Supply 5v DC power to Receiver (RX, Decoder). Refer to p.22.

-5 -
5. Systems Requirements for Setup
♦Hardware requirements
▶You must have a HDMI graphic controller or card having a HDMI or DVI port in your PC
or any other equipment being used.
▶It should support the maximum graphic resolution of displays to be connected.
▶No special requirements for memory size, CPU speed and chipsets, if you’ve already
properly installed your HDMI graphic controllers or cards.
♦Software requirements
▶You need to check OS version of your PC or any other equipment being used. [TBD]
♦Network requirements
▶You may need Ethernet switch as a switching hub or router for connecting multiple
IPKVM -500-EDs on Local LAN or Intranet. Because IP Video Wall Controller, IPKVM-
500-ED is based on multicast protocol for A/V streaming, the network switch has to
support Gigabit Ethernet, Jumbo frame, and IGMP snooping with L2 Switch and Gigabit
Ethernet, Jumbo frame, IGMP and multicasting protocol with L3 Switch.
Note: In some network switches, there may be a problem with video streaming because of
capacity performance, even though they support these functions.
* Opticis tested and confirmed the performance of L2 & L3 switches as below. So, opticis
recommends user to use the switches for easy set-up.
▶List of L2 switches
NO
Product Model
Description
Netgear
1
GS724T
10/100/1000 24Port + SFP 2Port, VLAN, jumbo frame, IGMP snooping
2
GS7224
10/100/1000 24Port + SFP 4Port, VLAN, jumbo frame, IGMP snooping,
3
GS7248
10/100/1000 48Port + SFP 4Port, Jumbo frame, IGMP snooping,
HP (3com)
1
HP 1620-8G
10/100/1000 8PORT (no SFP port), Jumbo frame, IGMP snooping, web management
2
HP 1620-24G
10/100/1000 24Port (no SFP port), Jumbo frame, IGMP snooping, web management
3
HP 1620-48G
10/100/1000 48Port (no SFP port), Jumbo frame, IGMP snooping, web management
4
HP 1910-48G
10/100/1000 48Port +2 SFP port, Jumbo frame, IGMP snooping, web management
Cisco SB
1
SG300-10
8-port 10/100/1000 Gigabit Switch + 2 COMBO Mini-GBIC / SFP port
IGMP snooping, Jumbo frame ( Bandwidth - 20G / throughput - 14.88M )
2
SG220-26
26-Port Gigabit Smart Plus Switch ( ACL , CLI )+ 2 COMBO Mini-GBIC / SFP port
jumbo frame, IGMP snooping, ( Bandwidth - 52G / throughput - 38.69 M )
3
SG220-50
50-Port Gigabit Smart Plus Switch ( ACL , CLI 지원) + 2 COMBO Mini-GBIC / SFP port
jumbo frame, IGMP snooping,, ( Bandwidth - 100G / throughput - 74.4 M )

-6 -
▶List of L3 Switches
(1) Cisco WS-C3560X-24(48)
(2) Alcatel-Lucent OS6850-24(/48)
(3) Huawei S5720-28(24/48)p
(4) 3com (HP) 3CR17254-91 (HP5500G-24(/48)G)
▶For more technical support including bandwidth design, network topology, and selection &
setup with Network Switch (L2/L3), visit Opticis web site, www.opticis.com, or contact
[email protected]
▶But, point-to-point connection between one pair of IPKVM-500-ED can be directly
connected (with CAT5e or CAT6) without network switch.
♦Control PC requirements
▶Provided PC program to manage user accounts, network information and connection of
IPKVM-500-EDs.
▶Requirements: Windows XP and Window7 (and its higher versions).
♦AC / DC Power Adapter Technical Advisory
▶The IPKVM-500-EDis designed to use mainly external +5V AC/ DC power adaptor. The
internal power supplied through a HDMI pin (#18) from the graphic source is used to
identify normal connection between a source and TX, IPKVM-500-E.
♦Connector descriptions
▶5V AC/ DC Power (TX& RX):
Connect the 5V AC / DC Power Adaptor to the connector of each device. When the 5V
AC/DC Power Adaptor is connected to the device, the power LED is turned on. For more
information on LEDs, see “LED indication”
▶HDMI IN (TX):
Connect a video source (such as a PC) to HDMI IN receptacle over HDMI cable.
▶HDMI OUT (RX):
Connect a digital display to HDMI OUT receptacle over HDMI cable.
▶Local Display (TX):
Connect a digital display to Local Display receptacle over HDMI cable.
▶RJ-45 (TX & RX):
Connect a RJ-45 network cable (CAT5e / CAT6) to this connector.
▶mini USB port (TX):
Connect a USB port in PC to this connector for HID mouse or Keyboard.
▶USB A Type (TX):
Connect a local mouse and/or a keyboard with 2 port USB hub.

-7 -
▶Dual USB A Type (RX):
Connect a mouse and/or a keyboard to these connectors.
▶RS-232 (TX & RX):
Optional - Connect a RS-232 cable to this terminal block for knob or controller (for control
an instrument or receiving data from an instrument).
▶DIO (TX & RX):
Optional - Connect a DIO cable to this terminal block for knob or console switch / console
indicator (set and display Local / Remote Authority).
Note1: If you change a video source to another one, you have to reset the power of all TXs
and RXs by re-plugging of the +5V power adaptor.
Note2: If you want to use the function of RS-232 & DIO, please contact s[email protected].
♦IPKVM-500-E, TX Back
♦IPKVM-500-E, TX Front
Mini USB
from PC
USB A for
Mouse / Keyboard
DIO / RS-232
(Terminal Block)
Power Jack
(5V, 3.5mm)
HDIM IN
(Source)
HDIM OUT
(Monitor)
RJ-45 Port
(LAN)
Line in
from PC

-8 -
♦IPKVM-500-D, RX Back
♦IPKVM-500-D, RX Front
7. Setting Local / Remote Authority on TX module
♦3-state Slide Switch
You can set user’s authority of keyboard and mouse to Local, Remote, or Console site
(L/R/C) by 3-state Slide Switch as above. “L” means Local state, “R” means Remote state,
and “C” means Console state. Console State can be selected to Local or Remote state by
external console switch. Refer to Page 21, “External Local/Remote Authority Setting”.
8. LED Indication
IPKVM-500-ED has two (2) LEDs for Power and Authority status located on the front panels.
♦Power status LED (Red)
The red LED will be turned on when 5V power applied.
USB A for
Mouse / Keyboard
DIO / RS-232
(Terminal Block)
Power Jack
(5V, 3.5mm)
HDIM OUT
(Monitor)
RJ-45 Port
(LAN)

-9 -
♦Link LED (Green)
If the green LED turns on at TX and RX, it is ready to operate as IPKVM Extenders.
9. SW & Factory Reset
♦SW Reset: Press the Reset switch on the back of devices shortly to reset
♦Factory Reset: To recover the Factory setting, press and hold the Reset switch on the back of
devices until the LED is turned off after blinking (approx.5sec).
▶DHCP IP mode
▶default values on device setup & system configuration
▶default values on HDMI EDID
10.Connection
Important: Please keep the installation procedure below. Improper or no operation may result if the
start-up sequence is not followed correctly.
Step 1
Carefully unpack the contents of the shipping group.
Step 2
Turn on the PC, display, and network server
Step 3
Connect HDMI IN port in IPKVM-500-E (TX) to the PC by supplied HDMI cable.
Step 4
Connect mini USB port in IPKVM-500-E (TX) to USB port in PC with supplied USB cable.
Step 5
Connect Local Display port in IPKVM-500-E (TX) to local HDMI display by HDMI cable.
Then, connect the local Keyboard and Mouse to two (2) USB ports using USB hub. You may
skip Step 5 if you don’t need local control.
Step 6
Connect LAN port (RJ-45) in IPKVM-500-E (TX) to LAN port in Network server with LAN cable.
Step 7
Connect HDMI OUT port in IPKVM-500-D (RX) to remote HDMI display by supplied HDMI
cable. Then, attach keyboard and mouse for remote control.
Step 8
Connect LAN port (RJ-45) in IPKVM-500-D (RX) to LAN port in Network server with LAN cable.
Step 9
Plug the +5V power adaptors to both IPKVM-500-E (TX) and IPKVM-500-D (RX).
Note: If you change an input source to another source, you have to reset the power of all TXs
and RXs by re-plugging of the +5V power adaptor.

-10 -
11.Remote Manager (PC Program)
Note: IPKVM-500-ED supports static fixed IP address, auto IP address and DHCP IP (Dynamic
Host Configuration Protocol: default) in IP network. Users can change auto IP to static IP
with host & client device setup of PC Program if there is no DHCP server.
Important: Without DHCP IP, Static IP ‘Class’of Control PC should be the same as IP ‘Class’of
network switch or devices (TX or RX).
1) Download the PC program
(1) Visit our website, www.opticis.com
(2) Click the PRODUCTS bar at the top of the page.
(3) Click IPKVM and IPKVM-500-ED step by step.
(4) Click and download the PC program file.
(5) To download it, please enter the password number: 0315.
2) PC Program Installation
Important: If you use IPKVM-500-EDs in intranet between routers, you need to check the IP
addresses, Gateway and Subnet Mask of the PC.
(1) Run the setup.exe in the Window Operating System.
(2) Follow on-screen instructions.
* To re-install or upgrade the PC Program, please delete the previous PC program on the
Control Panel of Window OS.
3) Access to menu of PC Program
(1) Run the PC program (Remote Manager)
(2) Four (4) menus: Device Setting, Advanced Setting, EDID read/write & Update Firmware.
Note: User can check the version of PC Program through the top of the menu bar. (Help 
About)
Important: Before connecting all TXs and RXs in the network that have default IP addresses,
please modify information of each TXs and RXs one by one by connecting it directly PC
with Remote Manager.

-11 -
4) Device (Host /Client) setting:
It helps to find all TXs and RXs in the network and register automatically. But please remind
that all TXs and RXs in the network should have different IP address. If you connect TXs and
RXs in the network for the first time, please do modify network information of each TXs and
RXs as below.
♦Modify IP address and device information on the network
(1) Click ‘Searching’button.
Then, Remote Manager detects connected devices and shows on left list window.
(2) To modify connected devices, select one of listed devices on the left list window. User
can modify IP address, gateway, and subnet mask of the devices on the right window.
(3) Add device name on the right window.
It supports up to 32 characters including numbers and English alphabets.
(4) Click ‘Sync’ button to save and use TX or RX information.

-12 -
♦ ‘Reboot’ button: Re-boot selected device on the network if it needs.
5) Advanced Setting: configuration of Bit rate, OSD display and Blocking
Default values are: Bit rate: 200(Mbps) / OSD: on / Blocking: disable/Jumbo frame enable
Important: It recommends that these advanced settings are applied to all hosts or clients
because all devices need to have same configuration for fast switching with bit rate
and blocking and EDID data.
♦Bit rate setup
It is able to choose bit rate between 50~200Mbps or Best, according to required image
quality and bandwidth limitation of the network (If best bit rate, IPVDS-500-EDs are in
‘Visually lossless compression’).

-13 -
(1) Select one between 50MHz~Best
(2) Click ‘Save & Reboot’ to save and apply to TXs (All hosts is recommended).
♦ODS on/off
(1) Select on or off.
(2) Click ‘Sync’ to save and apply to RXs. (Client All or selected client)
* For details, please refer to Page 19 to figure out OSD mode.
♦Blocking
(1) Select enable or disable.
(2) Click ‘Sync’ to save and apply to RXs. (Host & Client All is recommended)
* Blocking function is to give user an authority on a host which you already occupied on a
client and then, other user cannot access the host. If user set blocking ‘enabled’ mode, only
one client can access to one host and control a source of the host (1:1 unicast mode).
If user set blocking ‘disabled’ (default) mode, one audio/video source of a host can be
transmitted to display monitors of many clients and controlled with keyboard and mouse on
the network (1:N multicast mode, default).
For details, please refer to Page 18, Multicast streaming and blocking function.
- Available: These TXs are ready to connect with this receiver.
- Currently connected: The RX is already connected to TX.
- Not available, in use (Red color): these TXs are already connected to other RXs. This
status message will be shown with blocking function ‘disabled’ only.
♦Jumbo frame
Please set ‘Disable’, if L2/L3 network switch does not operate well with Jumbo frame ‘Enable’.
♦Network Interface Selection
Please set Ethernet or WiFi, if there are some problems with device searching.
6) EDID read/write
♦EDID read from a client (RX)
(1)Select one of a client (RX) on the list. Connect a display to HDMI OUT receptacle of the
selected RX over HDMI cable.
(2) Click ‘EDID Read’ button. Then, you can see the saved EDID data as below.
* If the RX isn’t connected with display monitor, you can see ‘Fail’ message.

-14 -
♦EDID read from a host (TX).
(1) Select one of a host (TX) on the list. Connect a display to HDMI OUT receptacle of the
selected TX over HDMI cable.
(2) Click ‘Read EDID’ button. Then, you can see the saved EDID data as below.
* The TX isn’t connected with display monitor, you can see ‘Fail’ message.
♦EDID write from a host or a client to all hosts (recommended)
After you read EDID data from a client or host, you can write the saved EDID data on the
clipboard to all TXs or selected one.
(1) Select all TXs ( all hosts recommended)
(2) Click ‘EDID write’ button.

-15 -
♦EDID write from default EDID data to all hosts (recommended)
After you check the default EDID data between HDMI and DVI on the top right, you can write
the default EDID data to all TXs or selected one.
Default EDID value is HDMI on the product.
(1) Select Default HDMI or Default DVI.
(2) Click ‘EDID write’ button (all hosts recommended).
7) Update Firmware
♦Update Firmware by PC Program (Remote Manager)
(1) Click ‘Search’ button to find devices to upgrade on the network or directly with PC
(2) Select a device to upgrade on the left list window.
Note: User can see the present Firmware version of the selected device on the right side
window.
(3) Please check the IP address and Gateway of the PC. It must have same IP class with the all
of TXs and RXs.
Note: If IP address class and Gateway of PC is different from the selected device, change IP
address and Gateway of PC on the control panel.
(4) Click ‘File Open’ button. Search and select a firmware file.
(5) Click ‘Upload’ button.
(6) Please wait until LED blinking stops and then the device will be rebooted.
Note: You can see a pop up message when it completes. It takes about 3 minutes for TX and
5 minutes for RX.

-16 -

-17 -
♦Update Firmware by USB
Note: Please keep this guide carefully to update the firmware without fail. Unplugging of DC
power during the uploading process will result failure of boot loader in TX and RX.
(1) Copy “IPKVM-500.bin” to an USB memory stick.
(2) Insert the USB memory stick to any USB A ports on the selected TX or RX.
(3) Unplug and plug the DC power to the power jack of selected device. (IPKVM-500-E or D)
(4) Please wait until LED blinking stops and the device is rebooted. It takes about 3 minutes for
TX and 5 minutes for RX. (Do not unplug DC power until it finished)
(5) Remove the USB memory stick from the device (IPKVM-350-E or D)
12. IPKVM-500-ED Connection & Operation
1) GUI
Connection can be managed on a GUI of each client (RX)
When TXs and RXs are in the TCP/IP network, you can see all hosts (TXs) with each IP
addresses and device information on the GUI of a client (RX).
▶Press a hotkey to enter into the GUI menu on the connected keyboard
- Ctrl + Alt + Shift + Backspace
- Ctrl (right) + Enter
- Ctrl (right) + ESC
▶Press a hotkey to exit from the GUI on the connected keyboard
- ESC key
♦IP Address/Device Information and status will be shown as below.
Note: You can select and connect to an available TX, but please remind that with blocking
function ‘disabled’ in multicast mode(1:N), many client may access to a host with a
keyboard and mouse at local and remote site. For details, please refer to Page 18,
multicast streaming and blocking function.
2) Connection & Operation
♦Connection
(1) Press ‘hotkey’to enter into a GUI of a client on the keyboard.
(2) Select an IP of available TX.
(3) Press [Enter] button on the keyboard or click [Connect] button on the GUI.
♦Switching to another host (TX)
(1) Press ‘hotkey’to enter into GUI menu if you want to connect another host.
(2) Select one of available hosts.
(3) Press [Enter] on the keyboard or click [Connect] button on the GUI.
(4) Press [ESC] key on the keyboard if you want to return to current image screen without
switching action.
♦Dis-connection
(1) Press ‘hotkey’to enter into a GUI of a client on the keyboard.
(2) Click [Disconnect] button on the GUI.

-18 -
♦Operation with HID KVM
IPKVM-500-ED provides HID with a keyboard and a mouse. If you first connect mini-USB port
of the host (TX) to USB port of PC source with USB cable, you are ready to use a keyboard
and mouse in HID mode on remote or local site.
▶HID KVM mode on remote site
After connecting between a host and a client over IP, you can use a keyboard and a mouse
in the HID KVM mode at the remote site.
▶HID KVM mode at the local site
You can also use a keyboard and a mouse in the HID KVM mode at the local site which
can be connected to USB interface of the host with 2-port USB hub.
(1) Connect USB hub for a keyboard and a mouse to USB A port of TX to use KVM on the
local site.
Important: You can select and connect to an available TX, but please remind that you
first check blocking function ‘enabled’ if you use HID KVM in unicast mode (1:1) in
application such as ROS. For details, please refer to Page 18, multicast streaming
and blocking function.
(2) Set ‘Local or Remote’ with the Console Switch.
3) Operation with Audio Port
Note: Select one of audio port available (Analog audio Line-in port or HDMI audio) to connect
to TX. But, regardless of port selection, user can get audio output at both of HDMI audio
and Analog Line-out at the RX (Dual output).
♦HDMI audio input port selected with HDMI interface
When user connect HDMI audio source to TX over HDMI cable, both HDMI audio output port
and Analog Line-out port operate at RX. And also, HDMI audio output operates at TX.
♦Audio input port Selected with DVI/Analog Line-in interface
When audio input port is connected by DVI/Analog line in to TX, both HDMI Audio port and
Analog Line-out port operate at RX.
Note: Some PC with HDMI audio and analog audio Line-in are connected simultaneously,
audio output port may not operate properly at the client (RX).
Note: If input port by DVI is connected, audio output port may not operate at TX.

-19 -
4) Multicast streaming and Blocking function
♦Multicast streaming (1: N) with blocking function ‘disabled’
Please set blocking function ‘disabled’ on PC Program (Remote Manager), and then you may
see status of hosts (TXs) on the GUI of a client (RX).
- Available: Hosts (TXs) are ready to connect with the client. (TX)
-Currently connected: this client (RX) is already connected to the host (TX).
Note: When IPKVM-500-ED works as multicast mode, many client users may connect to a host.
But first user who uses keyboard and mouse at first has priority. If the user does not use
the keyboard and mouse for three (3) seconds, priority can be changed to another user.
♦Unicast streaming (1:1) with blocking function ‘enabled’
Please set blocking function ‘enabled’ on PC Program (Remote Manager). You may see
status of hosts (TXs) on the GUI of a client (RX) as below.
- Available: The hosts (TXs) are ready to connect with the client.
-Currently connected: The client (RX) is already connected to the host.
- Not available, in use (Red color): These hosts are already connected to other clients (RXs)
individually, user cannot access to these hosts.
5) OSD display
Device information of TX and RX will be shown on the monitors for users or operators. You can
inserts up to 32 characters including numbers and English alphabets.
Note: If you don’t want to show it on display, please don’t insert information at the ‘Device
Setting’ menu, or set ‘OSD’ to off at the ‘Advanced Setting’ menu.
You can see OSD messages on the display of the client (RX) as below.
▶Device information of the host (TX): Source10
▶Device information of the client (RX): Place10

-20 -
13.Product Specifications
Item
Description
Network
100/1000 Base-T Ethernet: TCP/IP based wired network with CAT5e/ CAT6 Cables
Resolution
Up to 3840x2160@30Hz or 1080p@60Hz
Video Interface Standard
HDMI 1.4 and DVI1.0
HDCP
HDCP 1.4 and 2.2
Multicast streaming
1 to N (up to 200 RXs)
Video latency
< 1 frame
TX Video Interface
Input: 1 HDMI/DVI Input
Output: 1 HDMI/DVI Output (Loop-Through)
RX Video Interface
Output: 1 HDMI/DVI Output
Keyboard/Mouse (TX)
1 x mini USB B type to PC
1 x USB A type (for Local HID Keyboard/Mouse)
Keyboard /Mouse (RX)
2 x USB A type ( for Remote HID Keyboard/Mouse)
LAN Port
RJ-45 (TX/RX 1 port)
Audio Input (TX)
HDMI Audio, Analog Line-in & Line-out
Audio Output (RX)
HDMI Audio, Analog Line-Out (Dual output)
RS- 232 Port (optional)
3 Pin Terminal Block for Knob & alarm interface
3 Stage Slide Switch(TX)
Local/Remote/Console for Control Authority
Digital I/O Port (optional)
3 Pin Terminal block for Control Authority (Externally)
External Console Switch
(TX, Optional)
Terminal Block for Console Switch or Console Indicator
Reset Switch
SW reset & Factory reset
Configuration access
OSD GUI via Mouse/Keyboard for Connection & Status monitoring
PC Program (Remote Manager) for device setting, mode setting & etc
EDID
Built-in EDID & EDID Read/Write
Dimension
TX: 112 x 28 x 104mm (WHD), RX: 112 x 28 x 104mm (WHD)
Power
100-240VAC, 50-60Hz
5V/2AAdaptor
Power Consumption (TBD)
TX < 5W
RX < 5W
Operating Temperature
0 ~ 50°C
Storage Temperature
-20 ~ 60°C
Certification
FCC, CE