OS SEP Series User manual

1
SE113Z24E
SEP
SET
■ Please kindly read this instruction manual carefully and use the product properly. This manual
should be kept for future reference.
Electric Screen
Index
SafetyPrecautions ・・・・・・・・・・・・2～3
Accessories ・・・・・・・・・・・・・・・・4
Aboutfabric ・・・・・・・・・・・・・・・・5
How to use ・・・・・・・・・・・・・・・・・6
Preparation of the remote controller ・・・・・・・6
How to use (IRremote) ・・・・・・・・・・・・7
How to use (Wall switch) ・・・・・・・・・・・8
How to use (Operation) ・・・・・・・・・・・8～9
Maintenance ・・・・・・・・・・・・・・・・10
FAQ ・・・・・・・ ・・・・・・・・・・・・10
Instruction Manual
Thank you forpurchasing OS product.
The installation of the device requires technical knowledge
and please do not installit on your own.
● Please contact the installer or the distributor for
installation.
● To installers: After installation, please hand over the
manualto the user.
SEP/ P Selection
SET/ T Selection
*Outlet plug is not included in terminal model.

2
SE113Z24E
This icon warns that it may cause death or casualty if not following
the instruction closely.
This icon indicates that it may cause injury or damage to the
property.
SafetyPrecautions
Please strictlycomplywith the following for safety
This instruction manual is intended to prevent any danger to the user and the third parties, or any damage to the
property. The following indicators are to remind users to strictly observe the instructions.
■ Throughout our explanation, the possible damage which may be caused by any negligence or disregard of the
safety precaution is classified to different levels according to the severity.
This icon suggests that the action is strictly prohibited.
This icon suggests that thisis the necessary procedure to follow.
Forlongperiodusagepleaseensurethattheinstallationpositioniswithadequatestrength.
If the supportis not strong enough, the screen mayfalldown after long-period use.
The installation or dismantling should only be handled by more than one professional
technician.
Assemble thescreenbytwo or more people. It might fall off causing damages andharms.
Pull out the power plug, when smoke, heat, smell or strange noise happens.
The continuoususemaycauseafireandan electricshock.
●Stop using it,andconsult with the dealer or distributor.
Take off the dust, etc. of the power plug regularly.
It cau
ses an insulation failure due to moisture etc. when dust is piled up on the power plug, and
mightcauseafire.
● Pleasepullout thepowerplug, andwipewithadrycloth.
Make sure the power plug is inserted tightly.
When insertion is not enough, it may cause afirebythe electric shock and heat..
Take the power plug to connect, not the power cable.
Itmaydamagethepowercable andcauseafireandan electricshock.
■ For the precautions we recommend users to notice, we explain by
using the following
different categories (The following
are
just example
s
)

3
SE113Z24E
Do not connect the plug to power until the installation is finished.
Itmaycauseanelectricshock.
■ OS Screenwouldnotbe responsiblefordamagecausedbyimproperinstallationornaturaldisasterfactors.
D
o not operate the power plug with a wet hand.
Itmaycauseanelectricshock.
Stop using, when anything
like metal, water, or liquid goes into the screen, and pull out
the power plug.
Thecontinuous usemaycause afireand anelectricshock.
● Stop usingit,andconsult with thedealer or distributor.
Pull out the power plug, when the screenis not used for long.
The leak maycauseafire.
Donothanganyobjectstothescreen
Thismaycausedamagetothescreenandresultindanger.
Donotforciblypulloutthescreen.
This mayresult in damagetothe structureor the screen materials
.
Do not damage the power cable and plug.
It causes the electric shock, theshort, and a fire whenused with damage.
Donotalterthedesignordismantle
Itmaycausemajor failures.
● Contactthedealerordistributorfor repairs .
Do not touch the power plug when thundering.
Itmaycauseanelectricshock.
Withintheexpandedreachofthescreen,donotplaceanyobjectstoblockthescreenorobjectsthatareeasilybreakable.
Thismaycausedamagetothescreenortotheotherpropertiesinuse.
Donotplacesharpobjectsnearthescreen
Itmaycausedamagetothescreen .
Exchange the same twonew batteries.
When an oldbatteryis mixed, it may cause heat, liquid leakageand the explosion.
Do not use the screen near thestove and other heat sources.
Becausethe screenfabriceasilygetsburned, it mightcausefire.
Restorethescreentothecaseafteruse.
Hanging the screen for longtime maycause the fabric fallout.

4
SE113Z24E
■ Pleaseconfirmthe accessories before installation.
・ Accessories change according to the operation methods.
Operation methods Other accessories, screws etc.
Ｒ：
Ｒ：Ｒ：
Ｒ： Infraredremotecontrol
・ Infraredremotecontroller ×1
・Infraredreceiver ×1
・AAAdrybatteries×2
・Sticker(spare) ×1
・holder ×1
SEP(80～
～ ～
～150 inch)
Sliding bracket
×2
Screw A
Crossrecess
Truss tapping screw (4×40)×6
Screw B
Crossrecess
Truss tapping screw
(4×12)×4
Ｗ：
Ｗ：Ｗ：
Ｗ： Wall switch
Wall switch ×1 Relay box ×1
Ｓ：
Ｓ：Ｓ：
Ｓ： Set
Infraredreceiver
×1
Infraredremotecontroller Wall switch Relay box
×1 ×1 ×1
・AAA drybatteries×2
Holder ×1 ・Sticker(spare) ×1
SET(80～
～ ～
～150inch)
Screw A
crossrecess
Truss tapping screw (4×40)×6
※ The aluminum ceiling plate is not equipped with SET series. The SET series can be combined with
OS aluminum ceiling plate and/or the aluminum box. Please contact the dealer or the distributor for
details.
※ For the details of the accessories of the aluminum box, please refer to the installation manual of the
aluminum box.
Accessories

5
SE113Z24E
■Howto maintain “WG White“
The dust onthe surface should be brushed off with a soft cloth or brush.
When the dust cannot be taken off, use the soft adhesive tape to rip off, or clean with the wet cloth
(tightly
squeezed)and then with dry cloth.
This cleaningmethods are only for“WGWhite”. Do not apply the same to other surfaces.
Cautions in handling
The surface of the screen is speciallyprocessed to enhance projection image. The
contamination or damage mayresultin poorprojection image. Pay close attention to the
followings when handling this product.
Do not touch the screen surface.
Do not drawanything on the screen surface.
Do not rub or scratch the surface with anything hard.
Gentlywipe the dust off the surface with the softdrycloth or remove witha softbrush.
■ Th
e screen surface may have an odor at first. Please ventilate enough by opening the window.
Any such odor will gradually fade. When the odor is strong, please keep the screen pulled out,
evennot in use.
■ Be careful in repeating the screen going up and dow
n. The continuous use of the up and down
operations may cause the heat prevention circuitry work, and stop the screen. When this
happens, please operate after some time (15 – 20 minutes) for cooling off. (※
This is not the
breakdown.)
Neveruse a moist cloth orchemicals such as benzene, thinner etc.
It maycause the poorprojection image.
About fabric
Thescreensurfacemayhave anodoratfirst.Pleaseventilateenoughbyopeningthewindow.A
nysuchodor will
graduallyfade.
（
When the odor is strong, please keep the screen pulled out, even not in use. It might take several days till the
screendoesnot haveanodoranymore.)
Moreover, the rise of the temperature and humidity causes the odor. Ventilate it conti
nuously, when the odor is
strong in the summer time.
■Howto maintain “WF Pure Mat”
If the screen is dusty or dirty, brush away dust or dirt softly using an electrostatic brush or a fresh face
brush.
This cleaningmethods are only for“WF Pure Mat”. Do not apply the same to other surfaces.
A special processing is applied to the surface.
Do not fold or bend it in cleaning.
It mayruin the projection effects.
“WF Pure Mat” is textile fabric.
Do not rub, fold orbend it duringcleaning.
It mayruin the projection effects.

6
SE113Z24E
■ Operatingthe screen
Please refer to the operations in the manuals (Remote Controller S-R1 and wall switch S-R2).
■ Applyingtension to the screen
If the screen fabric is less tensionedaround the weight bar area after use, adjust the tension using the
tension adjustment mechanism.
※ Turn the knobs 3 timesclock-wise orcounter clock-wise atmaximum.
※ When tensioned too much, turn the knob counter clock-wise
to loosen the fabric. After leaving the screen for 2-3 days,
turn the knob to tighten again.
Please pull out the backpanel of the remote controller, and puttwo dry batteries
(size AAA).
Clock-wise：to tension
Counterclock-wise：toloosen
How to use
Dry batteries

Change the two batteries to the new ones
when the signalis weak.

Take out all the batteries when you do not
use it for long to avoid the liquid leakage
damage
Do not use rechargeable batteries.
The operationrange of IRremotecontroller
IRreceiver
Remote controller
Do not drop, throw away, or put water on it, or
it
may causethe breakdown.
Handle the remote controller carefully.

Please operate it to the direction of the infrared
receiver
Preparation of the remote controller

7
SE113Z24E
How to use (IR remote)
■ Storing the screen
When the screen is deployed, push theＵＰ
button of the
remote controller.
The screen is rolled up and stored, and it stops
automatically.
■ Stoppingthe screen
Pleasepush theＳＴＯＰbutton wheneveryou
want to stop
the operation.
■ Deploying the screen
Please confirm the screen is stored, and push theＤＯＷＮ
button of the remote controller. The screen is deployed to
a prescribed projection position, and it stopsautomatically.
UPbutton
(Thescreenmovesup.)
STOPbutton
(Thescreenstops.)
DOWNbutton
(Thescreenmovesdown.)

8
SE113Z24E
The projection position can be changed as desired.
●
●●
● To lift up the projetion positon
①
①①
① Stop at the desired position
UseＵＰ&ＤＯＷＮbuttons and push
ＳＴＯＰbutton at the desired position.
How to use (Wall switch)
■ Storing the screen
When the screen is deployed, push theＵＰ
button of the
wall switch.
The screen is rolled up and stored, and it stops
automatically.
■ Stoppingthe screen
Pleasepush theＳＴＯＰ
button wheneveryou want to stop
the operation.
■ Deploying the screen
Please confirm the screen is stored, and push theＤＯＷＮ
button of the wall switch
. The screen is deployed to a
prescribedprojection position, and it stops automatically.
ＵＰ button
(Thescreenmovesup.)
ＳＴＯＰ button
(Thescreenstops.)
ＤＯＷＮ button
(Thescreenmovesdown.)
How to use (Operation)

9
SE113Z24E
②
②②
② Memorizing the position
1. At the desired position, pushＳＴＯＰbutton
for5-6 seconds, and then push
ＤＯＷＮbutton within 2 seconds.
2. Upon receivingthe command, the screen
moves up approx. 10cm, and then
stops atthe preset position.
●
●●
● To lift down the projection position
①
①①
① Deploythe screen
Push ＤＯＷＮ button for5-6 seconds
and the screen starts to come down from
the preset position.
Push ＳＴＯＰbutton.
②
②②
② Stop at the desired position
Use ＵＰ& ＤＯＷＮbuttonsand push
ＳＴＯＰ button at the desired position.
③
③③
③ Memorizing the position
1. At the desired position, pushＳＴＯＰbutton
for5-6 seconds, and then push
ＤＯＷＮbutton within 2 seconds
2. Upon receivingthe command,the screen
movesup approx. 10cm,and then
stops atthe preset position.
※ NOTICE If the ＤＯＷＮbutton is pushed for some
time and leftas it is, the screen comes to
the factorydefaultposition, and stops.
The screen cannotbe lower than this
position.

10
SE113Z24E
● The replacement of the fabric
・When the screen fabric is damaged, the fabric can be replaced.
・For details, please contact the dealer or distributor.
・For details on replacing the fabric, please refer to the attached manual of the replacement
fabric.
Symptom Check Remedy
The projected image
becomes inclined. Is the screen mounted horizontally? Check the mounting holes.
Is powerplugfixedto the mains
correctly? Fixthe plugtightly.
Is the remote controllerdirected
to the receiver? Direct the remote controller to the receiver.
Anything blockingbetween the
remote and receiver? Take off the blockingitem, or change the receiver position.
Is the sun or lightsreflected on
the receiver? Change the position of the receiver.
Batteriesof remote low? Change the two batteries in the
remote.(AAA type)
Is the heat prevention circuitry
on? Cool off the motor and operate again after 10-20 minutes.
Is the receiver cable extended?
If the receiver cableisextended, it
is easily affected by the noises.
Anymodifications on the productor
the accessories would be subject to
non-warranty.
The screen does not work.
Is wrongstop position defined? Push ＤＯＷＮ button for5-6
seconds and the screen starts to
come down from the preset position.
Maintenance
FAQ

11
SE113Z24E
OSI CO., LTD.
Room1605, 16/F, SeaviewCentre, 139Hoi BunRoad,
KwunTong, Kowloon, Hong Kong
PHONE :[phone] FAX: [phone]
E-mail:[e-mail]
URL :http://www.os-worldwide.com