oserio FTG-315 series User manual

www.oserio.com
Body Fat Monitor Instrucon Manual – FTG-315 series
Body Fat Monitor
Thank you for selecng oserio series of Health Management Products.
This Instrucon Manual will guide you through the setup procedures and outline the key features.
Please keep the instrucon manual at hand all the me for future reference.
Manufactured by:
Charder Electronic Co., Ltd.
No.103, Guozhong Rd., Dali Dist.,Taichung City, 412 Taiwan (R.O.C.)
PA-0051-V1.0

1
1
2
16
18
19
20
Table of Contents
Before Using the Monitor
1.1 Overview
1.2 Baery Installaon
1.3 Product Features
1.4 Introducon
1.5 Important Safety Notes
1.6 Used Symbol Descripon
1.7 EMC Guidance and
Manufacturer's Declaraon
1
2
3
4
5
8
9
Operang Instrucons
2.1 Measuring Body Composion
2.2 Error Message List
More Informaon
3.1 Care and Maintenance
3.2 Product Specificaon
FTG-315 series
Body Fat Monitor
Front Rear
Baery Cover
Feet
Plaorm
Bluetooth Indicator
LED display
Before Using the Monitor
1.1 Overview

NOTE:
Be sure that the polarity of the baery is set properly.
2
Please verify if the baeries are installed correctly
Install 4 ”AA” size baeries properly
Open the baery cover
Before Using the Monitor
1.2 Baery Installaon
Before Using the Monitor
1.3 Product Features
3
1. Measure weight, body fat, BMI, visceral fat, muscle rate and body age.
2. Data reference from Body fatness and risk for elevated blood pressure, total cholesterol, and serum
lipoprotein in children and adolescents American journal of public health. Aer compared measurement
value, indicator will shows “Low, Normal, High, Very High”
3. Large LCD display (76 x 36mm).
4. User friendly design with colorful and interesng face icons.
5. Compact design.
Body Fat References：Daniel P. Williams, Sco B. Going, Timothy G. Lohman, David W. Harsha, Satharnur R Srinivasan, Larry S.
Webber, Gerald S. Berenson, Body fatness and risk for elevated blood pressure, total cholesterol, and serum lipoprotein raons in
children and adolescents American journal of public health, March 1992, Vol. 82, No.3
21

45
Before Using the Monitor
1.4 Introducon
Product descripon: This unit is measuring the user’s body weight and to esmate the value of
the Bio-Impedance body composion.
Product use: Body Fat, Visceral Fat, BMI, Muscle Rate, Body Age and Body Weight.
Essenal Performance: To supply the accurate measuring results which defined at Product Specificaon
either by FTG-315 itself or via a compable smart phone.
Measuring Principle: Biological impedance Analysis (BIA) works together with such as gender,
height, weight, age, other relevant factors, conversion of the user’s body
composion to determine whether the body is obese.
(If input profile is incorrect, it would result in incorrect measurement values.)
Recommended Measurement Times: It is recommended to use this unit in the same
environment and daily circumstances.
1. People with an electronic medical implant, such as a pacemaker, should not use a Body Fat Monitor
as it passes a low-level electrical signal through the body, which may interfere with its operaon.
2. Pregnant women should use weight funcon only. All other funcons are not
intended for pregnant women.
3. Keep out of reach of young children.
4. Do not jumping on the unit plaorm.
5. Do not step on the edge of unit plaorm.
6. Person with disabilies or physically frail should be assisted by another
person when using this unit.
7. Do not disassemble or modify the unit.
8. Using the baeries specify by the product specificaons, polaries match
the polaries of the baery compartment as indicated.
1.5 Important Safety Notes
Before Using the Monitor

76
9. Remove the baeries if the unit not be used for three months or longer.
10. If the display not shows, check the baeries.
11. Do not mix old and new baeries or different types of baeries to extend the life of the unit.
12. Do not use the unit on slippery surfaces such as le floors or wet floors.
13. Place the unit in an area free from direct sunlight, heang equipment, high humidity or extreme
temperature change.
14. Avoid excessive impact or vibraon to the unit.
15. Never submerge in water. Use alcohol to clean the electrodes and glass cleaner (applied to a cloth first)
to keep them shiny.
16. Place the unit on a hard, flat surface where there is minimal vibraon
to ensure safe and accurate measurement.
1.5 Important Safety Notes
Before Using the Monitor
17. Always remove your socks or stockings, and be sure the soles of your feet are clean before stepping
on the measuring plaorm.
18. Properly dispose of baeries according to applicable local regulaons.
19. This unit is intended for home use only. It is not intended for professional use in hospitals or other
medical facilies.
20. These baeries should be kept away from small children.
If swallowed , promptly seek medical assistance.
21. Expected Service Life: 5 years

8 9
Before Using the Monitor
1.7 EMC Guidance and Manufacturer's Declaraon
Guidance and manufacturer’s declaraon-electromagnec emissions
The FTG-315 is intended for use in the electromagnec environment specified below. The customer or the user of the
FTG-315 should assure that it is used in such an environment.
Emission test Compliance Electromagnec environment-guidance
RF emissions
CISPR 11
RF emissions
CISPR 11
Group 1
Class B
The FTG-315 uses RF energy only for its internal funcon. Therefore, its
RF emissions are very low and are not likely to cause any interference in
nearby electronic equipment.
The FTG-315 is suitable for use in all establishments, including domesc
establishments and those directly connected to the public low-voltage
power supply network that supplies buildings used for domesc
purposes.
Harmonic
emissions
IEC 61000-3-2
Voltage
fluctuaons/flicker
emissions
IEC 61000-3-3
Not applicable
Not applicable
Before Using the Monitor
1.6 Used Symbol Descripon
Explanaon of the graphic symbols:
SN-135-00001
Designaon of the serial number of every device,
applied at the device.
(Number as an example)
“Please note the accompanying documents“ or
“Observe operang instrucons”
Idenficaon of manufacturer of medical product
including address
Charder Electronic Co., Ltd.
No.103, Guozhong Rd.,
Dali Dist.,Taichung City,
412 Taiwan (R.O.C.)
“Electro-medical appliance“ with aachment for
type BF
Carefully read this operaon manual before
setup and commissioning, even if you are
already familiar with oserio scales.
Dispose of old appliances separately from your
household waste!Instead, take them to
communal collecon points.
Transport and storage temperature limit
indicang the upper and the lower limit.
(Transport and storage temperature on
packaging)
+60˚C
-20˚C

10 11
Before Using the Monitor
1.7 EMC Guidance and Manufacturer's Declaraon
The FTG-315 is intended for use in the electromagnec environment specified below. The customer or the user of the
FTG-315 should assure that it is used in such an environment.
Guidance and manufacturer’s declaraon-electromagnec immunity Guidance and manufacturer’s declaraon-electromagnec immunity
Immunity test IEC 60601 test level Compliance level Electromagnec environment-guidance
Immunity test IEC 60601 test level Compliance level Electromagnec environment-guidance
Electrostac
discharge(ESD)
IEC 61000-4-2
Electrical fast
transient/burst
IEC 61000-4-4
± 6 kV contact
± 8 kV air
± 6 kV contact
± 8 kV air
Floors should be wood, concrete or ceramic
le. If floors are covered with synthec
material, the relave humidity should be at
least 30%.
± 2kV for power supply
lines + 1kV for
input/output lines
± 2kV for power
supply lines
Not applicable
Mains power quality should be that of a
typical commercial or hospital environment.
Surge
IEC 61000-4-5
± 1kV line(s) to line(s)
± 2kV line(s) to earth
± 1kV differenal
mode
Not applicable
Mains power quality should be that of a
typical commercial or hospital environment.
Voltage Dips,
short interrupt-
ions and voltage
variaons on
power supply
input lines
IEC 61000-4-11
<5% UT(>95% dip in UT)
for 0.5 cycle
40% UT(60% dip in UT)
for 5 cycles
70% UT(30% dip in UT)
for 25 cycles
<5% UT(>95% dip in UT)
for 5 s
Mains power quality should be that of a
typical commercial or hospital environment.
If the user of the FTG-315, requires
connued operaon during power mains
interrupons, it is recommended that the
FTG-315 be powered from an uninterrupble
power supply or a baery.
Not applicable
Not applicable
Not applicable
Not applicable
Power frequency
(50/60 Hz)
magnec field
IEC 61000-4-8
3 A/m 3 A/m The FTG-315 power frequency magnec
fields should be at levels characterisc of a
typical locaon in a typical commercial or
hospital environment.
NOTE: UT is the a.c. mains voltage prior to applicaon of the test level.

12 13
Before Using the Monitor
1.7 EMC Guidance and Manufacturer's Declaraon
Guidance and manufacturer’s declaraon-electromagnec immunity
Immunity test IEC 60601 test level Compliance level Electromagnec environment-guidance
Conducted RF
IEC 61000-4-6
3 Vrms
150 KHz to 80 MHz
Not applicable Portable and mobile RF communicaons equipment should be
used no closer to any part of the FTG-315 including cables, than
the recommended separaon distance calculated from the
equaon applicable to the frequency of the transmier.
NOTE1:
At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE2:
These guidelines may not apply in all situaons.
Electromagnec propagaon is affected by absorpon and
reflecon from structures, objects and people.
Field strengths from fixed transmiers, such as base
staons for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast
and TV broadcast cannot be predicted theorecally with
accuracy. To assess the electromagnec environment due
to fixed RF transmiers, an electromagnec site survey
should be considered. If the measured field strength in the
locaon in which the FTG-315 should be observed to
verify normal operaon. If abnormal performance is
observed, addional measures my be necessary, such as
re-orienng or relocang the FTG-315.Over the frequency
range 150 kHz to 80 MHz, field strengths should be les
than 3 V/m.
A.
B.
Radiated RF
IEC 61000-4-3
3 V/m
80MHz to 2.5 GHz
3 V/m
Where P is the maximum output power rang of the transmier in
was (W) according to the transmier manufacturer and d is the
recommended separaon distance in metres (m).
Interference may occur in the vicinity of
equipment marked with the following symbol:
Field strengths from fixed RF transmiers, as determined by an
electromagnec site survey , should be less than the compliance level in
each frequency range .
b
a
Recommended separaon distance:
d = 1.2 P
d = 1.2 P 80MHz to 800 MHz
d = 2.3 P 800MHz to 2.5 GHz

14 15
Before Using the Monitor
1.7 EMC Guidance and Manufacturer's Declaraon
0.01 0.12
0.38
1.2
3.8
12
0.23
0.73
2.3
7.3
23
N/A
N/A
N/A
N/A
N/A
0.1
1
10
100
Recommended separaon distance between portable and mobile RF communicaons equipment and the FTG-315
The FTG-315 is intended for use in an electromagnec environment in which radiated RF disturbances are controlled. The customer or
the user of the FTG-315 can help prevent electromagnec interference by maintaining a minimum distance between portable and
mobile RF communicaons equipment (transmiers) and the FTG-315 as recommended below, according to the maximum output
power of the communicaons equipment.
Rated maximum output
power of transmier
(W)
For transmiers rated at a maximum output power not listed above, the recommended separaon distance d in meters (m) can be
esmated using the equaon applicable to the frequency of the transmier, where p is the maximum output power rang of the
transmier in was (W) according to the transmier manufacturer.
NOTE1:
At 80 MHz and 800 MHz, the separaon distance for the higher frequency range applies.
NOTE2:
These guidelines may not apply in all situaons. Electromagnec propagaon is affected by absorpon and reflecon from
structures, objects and people.
Separaon distance according to frequency of transmier
(m)
150 kHz to 80 MHz
d =1.2 P
80 MHz to 800 MHz
d =1.2 P
800 MHz to 2.5 GHz
d =2.3 P

6. LED bar running during connecng with App.5. The measurement completed. (show weight reading)
7. Turning off automacally aer transming .
Operang Instrucons
Note:
The unit will shut down automacally if the weighing data can’t be transmied in 30 seconds .
1. Place the unit on a hard, flat surface .
3. Step on the scale, LED bar will flash twice then
display user’s weight.
2. Run o’care APP and enter “ ” bubble .
4. Measuring Body Composion .
2.1 Measuring Body Composion
Note:
If you didn’t step on the scale but LED bar is flashing , please await ll the LED turn off or re-install the baeries. Such occasional display
might be caused by the interference of environment; however, it won’t cause the FTG-315 permanently damage / malfuncon and, is no
related with the basic safety.
Place the unit on a hard, flat surface to avoid inaccurate measurement.
16 17
5
66
5 SEC. OFF
---
kcal
--- kcal
---
LV
--- %
---
kg
Today
Weight
2
1 3
STEP ON
4

Operang Instrucons
2.7 Error Message List
The product is low power but sll
workable while “LO” flickers.
Connecng error.
Please try again or contact our service line .
Connecng error.
Please try again or contact our service line .
Replace baeries immediately while
“LO” appears.
Overloading or loading is unbalanced
within 1 minute. Please stand sll
during measurement.
1918
More Informaon
3.1 Care and Maintenance
1. Store the unit in a safe and dry locaon.
2. Avoid place on the aisle, to avoid accidentally tripped over
pedestrians.
3. Never submerge in water.
4. Do not expose the unit to direct sunlight, extreme hot or cold temperatures
or high humidity.
5. Avoid contact with corrosive chemicals or gas.
6. Clean the unit with a so dry cloth for daily use.
7. Wipe the plaorm and display using clean so cloth.
8. Do not use benzene, detergents or gasoline to clean the unit.
9. Avoid rough, scking cloth, to prevent scratching the plaorm and screen panels.
10. Prevent water infiltraon affecng the measurement accuracy.

0~40kg：±0.4 kg , 40~150kg：±1%
More Informaon
3.2 Product Specificaon
Model Body Fat Monitor FTG-315
Note: 1. Body fat measurement is for users age 10~80.
2. Specificaons may be changed without prior noce.
External Dimensions Main unit: 320mm(d) x 320mm(w) x 39mm(h) LCD: 76mm(d) x 36mm(w)
Weight Accuracy
Seng Range Age:10~80 Gender: Male/Female Height: 100~199.5cm
Power Supply Weight Approx. 1.8kg4 AA baeries
Operang Environment
Limit
Storage Environment
Limit
Temperature 5˚C to 35˚C
Humidity 30% to 85% RH
Temperature -20˚C to 60˚C
Humidity 10% to 95% RH
Maximum atmospheric
pressure range
Maximum operaon
altude
1013hpa – 800hpa 2000m
Scale Display Content
APP Display Content
Weight: 5 ~ 150kg, Graduaon: 0.1kg
Body Fat: 5.0 ~ 50.0%, Graduaon: 0.1%
Accessories
20
Body Fat Status Category: Low/Normal/High/Very High
Visceral Fat Status Category: 1~3(Normal)/4~6(High)/7~9(Very High)
BMI: 0.0~150.0, Graduaon: 0.1
Muscle Rate: 0.0~100.0%, Graduaon: 0.1%
Body Age: 18~80
Visceral Fat Level: Level 1~9 with 1 level increment
Manual, Warranty card, Connecng instrucons
Health conscious‧Professional‧Innovave