Osmio Duo Hydrogen User manual

Telephone: [phone]
Email: [email protected]
Osmio Duo Hydrogen Water Bottle
Instruction Manual

Important features
Proton Exchange Membrane (PEM) technology.
State of the art Solid Polymer Electrolysis (SPE) technology.
Works with all types of drinking water but the water used must be safe to
drink.
Separates and expels harmful by-products of Chlorine, Ozone and Oxides.
Use the bottle on a flat surface or table to allow the ozone gas release valve
to open.
High quality Platinum coated Titanium Electrode Plates.
Thank you for purchasing this product, please read this manual carefully
before using the system, and keep it for future reference. If you have any
questions after reading this manual , please call us on 0330 113 7181
Product specifications
Power
USB 5V / 2A Output: ≤10W
Bottle Capacity
400 ml
Water Type Required
Allpotable drinking water
Water Temperature Range 32°- 140 °F / 0°- 60°C
Dimensions 2.6” x 9” H 67 mm W 225 mm
Unit Net Weight
1.2 lbs / 544 g
Hydrogen Generation Range
1.2 -2.4 ppm (depends on working time)
ORP Range
-350 mv ~ -750 mv
Bottle Material
Borosilicate glass

List of components
Please ensure that you have everything in this diagram as well as the adaptor
lid for the breathing cannula and the cannula tube. If there is anything missing
please contact Osmio water for support.
Bottle Cap
Glass Bottle
Generator Cover
(Protect for Travel)
Silicone Plug
(Wet storage)
Generator Base
Generator Waste Chamber
USB Charge port (in rear)
Generator Timer/Power
Generator Waste Cap
Ozone Gas Release Valve
USB Power Cable
USB Power Plug
Bottle Adaptors
(2 sizes)
Spare washers x 3

DO NOT LET THE GENERATOR DRY OUT - DO NOT LEAVE IT UNCOVERED, ALWAYS LEAVE A
SMALL AMOUNT OF WATER IN THE BOTTOM TO KEEP THE ELECTRODE PLATES MOIST,
INSTALL THE SILICONE GENERATOR PLUG WHEN STORING OR TRAVELLING
DO NOT OVERCHARGE THE BATTERY ON THE UNIT - AS SOON AS THE RED LIGHT STOPS
BLINKING AND REMAINS ON REMOVE FROM THE CHARGER
THE PURER THE WATER USED THE MORE HYDROGEN WILL BE PRODUCED
CLEAN THE UNIT TWICE PER MONTH AS DIRECTED
ALWAYS PLACE THE UNIT ON A FLAT SURFACE WHEN IN USE
Important Notes

Setting up
1. Wash off the sanitisation liquid - remove the glass bottle from the generator and
remove the lid and wash with warm soapy water.
2. Remove the silicone generator plug which is sealing the generator and keep this is in
a safe place. It is used to keep the generator moist during shipment and storage.
3. Attach the clean dry glass bottle back on to the generator by twisting the
bottle onto the generator and hand tightening. Screw the lid back on the bottle.
4. Insert the charging cable into the charging port (this has a silicone cover flap). Then
insert the USB side of the cable into the power plug and plug into an outlet.
5. Charge the bottle for 2-3 hours until fully charged and then remove charger.
6. With the bottle attached rinse out the generator with warm water.
7. Fill the bottle with clean drinking water.
8. Now you are ready to start the electrolysis process.
Quick start up guide
IMPORTANT: DO NOT OVER-CHARGE, OVER-CHARGING
WILL LEAD TO SHORTENED BATTERY LIFE

1. To begin the electrolysis process press the power button. The working indicator light
will turn blue, making H2for 5 minutes.
Pressing the button for a second time will turn the working indicator light green,
making H2for 7 minutes. Pressing the button a third time will turn power off.
2. After a 5 or 7 minutes cycle the working indicator light will turn off, completing the
process. For a higher concentration of H2, use the 7 minute cycle.
3. You can drink the hydrogen water directly out of the bottle or pour it into another
container. It is best to drink water within one hour. Hydrogen will dissipate over time.
4. If the working indicator light flashes red, this means the battery power is low and
needs to be charged.
5. Do not cycle the bottle more than once when drinking the water.
6. Make sure to operate the unit on a table or flat surface to allow the opening of the
ozone gas release valve on bottom.
Blue indicates a 5 minute cycle Green indicates a 7 minute cycle
How to operate the bottle
IMPORTANT: DO NOT CYCLE THE BOTTLE MORE THAN
ONCE BEFORE DRINKING

The breathing cannula is an alternative to drinking water when drinking becomes
restricted during air or car travel or in the evenings when drinking water before bed
can interrupt sleep with necessary trips to the bathroom.
There is only so much water you can physically drink in a day, but you can breathe as
long as you want to.
H2Gas Flow: 10- 20ml/min approximately.
Instructions
1. To use the breathing cannula please use the second bottle lid provided, this has
a snorkel valve protruding in the centre.
2. Attach the cannula breathing tube to the lid.
3. Fill the bottle ¾ of the way full, with water and screw on the adapter-Lid to the
top of the bottle with the Cannula breathing tube attached.
4. Place the loop end of the Cannula tube over your head and the two breathing
prongs into each nostril.
5. Adjust the slack-bead behind your neck to be snug against the back of your
head. Begin cycling the bottle on a 7 minute cycle repeatedly to create enough
pressure to push Hydrogen gas up the cannula tube and into your nose.
6. Continue cycling until you no longer desire to inhale the gas.
7. If using for a longer than 7 cycles please replace the water.
How to use the Breathing Cannula

If you are attaching any other bottle to this device follow the steps below.
1. Choose a suitable adaptor to match the bottle neck (there are two different ones
supplied), then screw the adaptor onto the generator tightly. Use the generator
cover sideways to screw the adaptor onto the generator.
2. Screw the generator (with adapter attached ) on to your bottle of choice, make sure
this is fairly tight like a cap to avoid leaking.
3. Turn over and generate up into bottle.
How to use adaptors for other bottles
IMPORTANT: USE THE SILICONE GENERATOR PLUG WHEN
THERE IS NOT BOTTLE ATTACHED TO HELP
KEEP THE GENERATOR MOIST

Do not leave the bottle on charge for longer than 3 hours. Always ensure to use all the
battery before recharging again. The unit will stop charging when the LED light stops
blinking, when this happens remove the bottle from charge. Over charging will lead to
drastic deterioration of the battery.
Never operate the generator without water in the bottle. Do not soak or submerge the
generator unit under water. Do not place the generator unit in a refrigerator or cooler.
Never use any chemical cleaners on Generator unit. Do not pull cable from wire or plug
with wet hands.
Depending on the mineral oxide content in your drinking water, clean the electrolysis
plates by descaling once or twice a month.
After 3 or more cycles some waste water may accumulate in the bottom chamber, to
release this, unscrew the bottom chamber and drain the water. If no water is discharged
in the waste chamber, that is normal, the machine is controlling pressure adequately,
waste O3 and Chlorine are discharged as a gas.
Never let the generator dry out, to ensure this does not happen leave a small amount of
water in the bottom to keep the electrode plates moist.
Keep USB Port sealed by plugging its cover back in.
Operate only with clean and safe drinking water, filtered water is preferable but tap water
can also be used. Not for use with hot, carbonated or other beverages. Use room temper-
ature water. Never freeze or use ice.
Avoid direct sun light or heat that can dry out the plates.
We do not recommend drinking water that has been cycyled more than twice, release the
gas pressure at the lid if cycling more than twice (if you do not have the cannula
attached).
Keep away from children, Pets, Heat and Flames.
Important things to remember

Depending on the mineral oxide content in your drinking water, clean the electrolysis
plates by descaling once or twice a month.
Using reverse osmosis filtered water will prevent the need for descaling but this is a
good process to follow to clean and maintain the bottle.
To descale simply add 1 part either white vinegar, lemon juice or citric acid to 3 parts
water into the bottle and leave generator soaking in mix overnight. Discad and rinse
thoroughly with warm water before using the next day.
The main thing to remember is to not over-charge and to keep the generator moist so
that the elecrolysis plates do not dry out
Trouble shooting
No visible bubbles • Check power source
• Remove plug and obstacles
Light blinks when
operating unit
• Low battery indicator
• Charge Unit
Low PPM levels
when tested with
H
2
Blue Drops
• Allow 7 days to break
-
in
• Operate for 7 minutes (2nd cycle option)
Wetness in Generator
• Units are shipped wet
Battery not charging
• Check for defective Plug or cable.
Bottle has odour or
Unit makes less gas
• Clean and de-scale as needed
• Use different water source
Unit stopped working
• Contact For Support
Glass bottle broke
• Contact to order replacement
Machine is
Leaking water
• Check all seals, tighten lid
• Check or empty waste chamber
• Fill water to ½ of top rim
Descaling and Maintenance
If you have any other issues or queries please contact us on:
Telephone: [phone]
Email: [email protected]

Enjoy your bottle!
If you have any questions, issues or concerns about this products please contact
Osmio Water for support. You can do this by visiting
https://www.osmiowater.co.uk/ or using the below contact options
Telephone: [phone]
Email: [email protected]