Honeywell HWDT-620W User manual

Please read and retain these instructions.
HWDT-620W

CONTENTS
Thank you for purchasing the HWDT-620W. This manual will provide you with
safety information, instructions for optimal use, and proper care and maintenance
for your product. Please read this manual carefully before operating.
SAFETY INSTRUCTIONS...................................................................................................3
PRODUCT VIEW.................................................................................................................4
QUICK START GUIDE ........................................................................................................5
INSTALLATION ..................................................................................................................5
MACHINE MAINTENANCE............................................................................................... 6
TROUBLESHOOTING .......................................................................................................7
SPECIFICATIONS ..............................................................................................................7
WARRANTY.........................................................................................................................8
2

When using this appliance follow these safety precautions to reduce the risk of fire, electric shock, or injury.
Read & Fully Understand This Owner’s Manual Before Using This Machine.
WARNING
1. Keep this appliance away from high temperatures and in a dry and ventilated place.
2. Never install this appliance in the open air or under rain or direct sunlight.
3. For your safety, this appliance should be properly grounded on a level surface indoors.
4. The appliance should be placed near an electrical outlet so that the outlet is easily accessible.
5. Make sure the voltage meets the appliance’s electricity requirements (120-volt/ 60Hz).
6. Do not operate if the electrical plug or power cord is damaged.
7. Only plug the appliance into an exclusive properly installed-grounded three prong wall outlet.
8. Do not under any circumstances alter the electric plug.
9. Do not use an adapter plug or extension cord with this appliance.
10. To prevent accidental injury, the cord should be secured behind the appliance and not left exposed or
dangling.
11. Do not pull out the cable to unplug.
12. Do not turn this appliance on/off by connecting/disconnecting it from the source of electricity.
13. A full water bottle must be connected to the appliance prior to being turned on. (See Page 5).
14. Pour water from the hot water faucet before plugging and switching the appliance on to heat. If the
dispenser is turned on with an empty tank, it can be damaged.
15. To reduce the possibility of malfunction, let the water cooler stand upright for approximately 24 hours
before connecting the appliance to the power source.
16. This appliance best operates in an environmental temperature between 64°F -100F°(18°C -38°C).
17. Only use compatible sized water bottles (3 or 5 gallons).
18. Keep the ventilation openings at the back of the appliance uncovered and unobstructed. Allow a
minimum of 8 inches distance from the back of the unit to the wall.
19. Keep gasoline or any other flammable vapors and liquids away from the water cooler.
20. Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
21. Do not place other appliances inside the bottom storage compartment.
22. If you want to move the water cooler, do not tilt more than 45º to avoid damage to the compressor.
23. This water cooler dispenses hot water at a temperature up to 203°F (95°C) so use caution when
handling the hot water tap.
24. Supervision of children when using is advised.
25. Do not operate the machine for any other purpose other than its intended use.
SAFETY INSTRUCTIONS
3

PRODUCT VIEW
1. Bottle Supporter
2. Front Housing
3. LED Indicators
4. Water Taps
5. Drip Tray
6. Heating Switch
7. Cooling Switch
8. Cold Water Temperature Regulator
9. Power Cord
10. Drain Plug
1
2
3
4
5
6
7
8
9
10
4

BEFORE PLUGGING IN THE UNIT TO A POWER SOURCE
WARNING: Before plugging in the unit, make sure to have poured water from the hot water faucet. IF THE
DISPENSER IS TURNED ON WITH AN EMPTY WATER TANK IT CAN BE DAMAGED.
1. Let the appliance stand upright for about 24 hours. This will reduce the chance of malfunction in the
cooling system from possible mishandling during delivery.
WARNING: The drain cap on the back of the unit may become loose during shipping. Fasten the drain cap
tightly before you start to operate the unit. If the drain cap is loose, the unit may leak and cause floor
damage.
2. Insert water bottle vertically through the water funnel.
3. Place a container under the hot and cold water faucets then push down both buttons to test if water is
flowing through the unit. To use the hot water, first press the hot water safety button.
4. Insert the power plug into the wall socket.
5. First, turn the hot water switch on the back of the unit into the ON position. Next, turn the cold water
switch into the ON position. DO NOT TURN ON BOTH SWITCHES AT THE SAME TIME. Once this is
completed both cooling and heating indicator lights should light up.
NOTE: The appliance is designed to provide hot or cold water whenever you need it. It will automatically
turn on and off when hot and cold water reaches the desired temperatures.
When operating the water dispenser for the first time, you will need at least 15-30 minutes for the hot
water to reach the desired temperature and 1 hour for the cold water to reach the desired temperature.
The water dispenser has 3 indicator lights on the front panel.
•When the right (icon) indicator light is on, the unit is in the process of cooling water inside the cold
water tank.
•When the left (icon) indicator light is on, the water dispenser is heating water inside the hot water tank.
•When you plug the water dispenser in, the middle (icon) indicator will be turned on. This means that
room temperature water can be dispensed.
Using the water dispenser
•To dispense hot water, press the hot water safety button and then push the hot water button down.
•To dispense cold water, push the cold water button down.
•To dispense room temperature water, push the room temperature button down.
•To use the Cold Water Temperature Regulator, turn the knob clockwise to get colder water and turn the
knob counter-clockwise to get warmer water. The default temperature is 45˚F.
•It is recommended that if the hot water option is not used, the hot water button (red switch) be turned
OFF. This will help conserve energy.
SET-UP/PRODUCT OPERATION
5