Ostar T210022 User manual

GEEVON
T210022 Atomic Wall Clock User Instructions
Thank you for purchasing T210022 Smart Atomic Luminous Clock.
Please take a moment to read this guide and store it for future reference.
The GEEVON Atomic Clock will receive daily WWVB updates. Daylight Savings Time also automatically updates so there is no need
to re-set the clock manually!
IMPORTANT: If the Atomic Clock does not receive the WWVB signal immediately, wait overnight and it
will be set in the morning.
The clock has a built-in receiver that automatically synchronizes itself with the WWVB radio signal broadcast by the US
Government's National Institute of Standards & Technology(NIST) in Fort Collins, Colorado.
QUICK START GUIDE
1. Choose your time zone [6] and DST [5](Daylight Savings Time) mode on the back of the clock.
2. Place 1 AA battery in the battery compartment. The clock hands will begin to move and the clock will start
searching for the signal.
3. In most areas, a signal can be received at night. If the clock doesn't receive the WWVB Atomic signal
immediately, wait overnight and it will be set in the morning.
Tips:
1. Please place the clock near the window to enhance the signal.
2. The Night Light Clock might run out of energy during a long day in the box, so we advise letting the
wall clock absorb light energy (sunshine or fluorescent lamp) more than 4 hours before installation when
receiving the products. (Please avoid direct sunlight.)

FEATURES
1. Reset
Press the RESET button once shortly, hour/minute/second hands will move to the 12 o’clock position and
clear all the internal information, and then re-enter the automatic radio signal reception status (the initial
state). The whole process takes 4~6 minutes.
2.REC(Force Receiving) BUTTON:
In normal mode, press and hold the REC button, and the hands will stop running and enter into Force
Receiving mode. It will start receiving the Atomic time signal within 10 minutes. At this time, the clock is
manually forced into the reception state and begins to receive the radio signals.
Once received the signal successfully, the clock hands will find the correct time and run normally.
Otherwise, it will return to the time before Force Receiving. If the Atomic signal is not received wait
overnight and it will be set in the morning.
3.M.SET (Manual Set) BUTTON:
In normal mode, keep pressing the M.Set button, and enter the manual setting, the minute hand will run
quickly (please note that the second cannot be adjusted). In the manual setting state, pressing the M.SET
button once, the minute hand will move forward one minute.
Once we release the M.SET button, the system will exit the manual time-adjusting state after 10 seconds
and keep running from the time we set (The clock has now exited the receiving state).
4. BATTERY INSTALLMENT
Insert one high-quality alkaline AA1.5V LR6 type battery into the battery slot correctly according to the
battery polarity instructions.
5. DST ON/OFF SWITCH:
Before inserting the battery, select the DST mode.
The clock has been programmed to automatically switch when daylight saving time is in effect.
6. TIME ZONE SWITCH:
Before inserting the battery, select the correct time zone. The default time zone is P(Pacific Time). If your
location is not in the Pacific, slide the time zone switch to M(Mountain Time) / C(Central Time) / E(Eastern
Time) zone.
7. RECEIVE RADIO SIGNALS AUTOMATICALLY EVERY DAY:
If the clock has not correctly received the radio signal on the same day, the signal shall be received at 8-time
points of the day: 2: 00', 3:00' / stop second, 4:00', 5:00', 14:00', 15:00', 16:00', 17:00'
1) To reduce the interference and facilitate the successful reception of radio signals, you should stop the
secondhand rotation is doing above reception, but the other needles should be normal.
2) If the clock is operated manually, the signals should be received seven times a day.
3) Each receiving time is about 3~12 minutes.
Need help? Please contact the seller on your order page or shoot an email to :
[e-mail].