OTS IES82162XMH-S-RP User manual

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES82162XMH-S-RP / version 1.0
Quick Installation Guide
IES82162XMH-S-RP
Product Overview
L3 Hardened Grade Managed 16-port 100/1000Base-SFP + 4-port 10GBase-SFP + 8-port
10/100/1000Base-SFP or 10/100/1000Base-TX Combo Optical Ethernet Switch. This switch is highly
flexible and anti-EMI. -40°～ 75°C operating temperature rang and 8KV Ethernet surge protection can
adapt to a harsh outdoor environment and ensure product reliability.
Product Features
➢16 x 100/1000Base-SFP + 4 x 10GBase-SFP + 8 x 10/100/1000Base-SFP or 10/100/1000Base-TX
Combo
➢Support Auto-MDIX, and Full/Half Duplex self-negotiation mode
➢Provide SC/FC/ST/LC interface fiber port, Support single/dual fiber transmission
➢Support 10K bytes jumbo frame, compatible with various extension protocols
➢8K MAC address table
➢Support IEEE802.3az Energy Efficient Ethernet technology
➢Electric 8KV surge protection, easy to use in outdoor environment
➢Complete status indicators, working state at a glance
➢Power input polarity protection design, no worry about wrong operation
➢Rugged metal housing, IP40 protection, fan-less design
➢Installation method: RACK
Package Content
⚫Managed Ethernet Switch x 1
⚫AC Power Cable x 1
⚫Mounting Accessory x 1

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES82162XMH-S-RP / version 1.0
⚫Quick Installation Guide x 1
LED indicator
All LED in the front panel of this series monitor the working status of the device, simplifying
troubleshooting. The indication of each LED is as below in the table:
System Status LED
LED
Status
Description
PWR1
Green on
Power1 normal
off
Power1 off
PWR2
Green on
Power2 normal
off
Power2 off
RUN
Blink
System run
off
System bad
ALM
Green on
System have alarm
off
System normal
FAIL (for PoE)
Green on
PoE out of control
off
PoE normal
MAX (for PoE)
Green on
PoE out total power max
off
PoE out total power normal
RING
Green on
RING run
off
RING off
RO
Green on
RING owner
off
Not RING owner
Ethernet Port
LNK
On
Ethernet port is connected
Blink
Data transmission enable
Off
Ethernet port is disconnected
SPEED
On
1000M
Off
NO 1000M
Installation Guide
Please use the associated devices for installation.
Installation:
1. Make sure output power of power adapter meets the requirements of switch showing in the label.

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES82162XMH-S-RP / version 1.0
Please install the switch by the following steps:
1. Place the switch on a sufficiently large and stable desktop or on solid rail.
2. Connect the switch to the power.
3. Connect the network devices with the corresponding port on the switch via network cable
Attention
1. Do not place heavy objects on the switch and ensure the switch always in good ventilation
environment.
2. Please power off before plug or remove power adapter.
Power On
Power on after connect switch to power. And then the switch will automatically initialize, the LED
indicator will have the following conditions:
1. After LED on and then off means that the system has reset successfully.
2. Power LED is on all the time.
Notice
If the initialization does not match instructions above, please check the power supply.
IP:192.168.0.5 (OOB) user: admin, password: admin;
IP:192.168.1.5 user: admin; password: admin;
General
To ensure trouble free transportation and storage, all OT Systems products must be thoroughly
inspected, tested and properly packed before delivery. Check the product upon receipt for any
visible damage which may have been caused during shipment.
-END-